ARMY MIL-DTL-3628 148-1996 DETAIL SPECIFICATION SHEET nBADGE IDENTIFICATION REFUGE OFFICER U S FISH AND WILDLIFE《美国鱼类和野生动物服务组织保护官员身份挂牌》.pdf

《ARMY MIL-DTL-3628 148-1996 DETAIL SPECIFICATION SHEET nBADGE IDENTIFICATION REFUGE OFFICER U S FISH AND WILDLIFE《美国鱼类和野生动物服务组织保护官员身份挂牌》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-3628 148-1996 DETAIL SPECIFICATION SHEET nBADGE IDENTIFICATION REFUGE OFFICER U S FISH AND WILDLIFE《美国鱼类和野生动物服务组织保护官员身份挂牌》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-DTL-3b2/L48 9999906 2025135 897 = NOT MEASUREMENT SENSITIVE MIL-DTL-3628/148 - SUPERSEDING 21 September 1994 MIL-B-41809/40B DETAIL SPECIFICATION SHEET BADGE, IDENTIFICATION, REFUGE OFFICER, U.S. FISH AND WILDLIFE This specification is approved for use by all Departments and Agencies of the Depa

2、rtment of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the issue of MIL-DTL-3628 listed in that issue of the Department of Defense Index of Specifications and Standards (DODISS) specified in the solicitation. MATERIAL: Gilding Met

3、al FINISH: Hard Enameled, Gold Plated, Matte Finish, Polished Highlights? and shall match TIOH Metal Finish Chip Number 8. DIMENSIONS: HEIGHT (Overall) : 2-5/8 inches (6.67 cm) (REF) WIDTH (Overall) : 1-13/16 inches (4.60 cm) (REF) THICKNESS (At Thickest Point): 0.085 inch k 0.010 inch (0.215 cm k 0

4、.025 cm) AMSC N/A FSC 8455 J7ISTRIBTION STATRMENT 4 . Approved for public release; distribution is unlimited. 1 of 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3b28/148 = 9Ob 2025336 723 MIL-DTL-3628/148 NOTES : Government furnished hub

5、or die. 1. The term (REF) refers to the measurements taken from the 2. Piercing shall be as indicated. 3. Enameled areas shall be as indicated. The color shall conform to the TIOH chip numbers listed below or the standard sample. . :OLOR Blue Black !2uuamm 18 (Backgrounds & “US”) 26 (Numbers) 4. Epo

6、xy resin (stoning epoxy) may be used in lieu of hard enamel at the option of the manufacturer. 5. Attaching device shall be of the following styles as specified in the procurement document. a. Money clip: The clip shall be 1-1/2 inch k 1/64 inch (3.81 cm k 0.04 cm) long and 5/8 inch f 1/64 inch (1.5

7、9 cm f 0.04 cm) wide with the top of the clip located at the top edge of the shield and hard soldered on the vertical center line of the reverse side of the badge. b. Pin and catch type: The pin shall be 1-3/4 inch k 1/32 inch (4.45 cm & 0.08 cm) long with a heavy duty top opening catch. The joint s

8、hall be located on the vertical center line 1/2 inch & 1/64 inch (1.27 cm - + 0.04 cm) down from the top of the badge. 6. The badge shall be numbered consecutively with the numbers specified in the procurement document. Numbers shall be 1/8 inch f 1/64 inch 40.32 cm f 0.04 cm) high, equally spaced,

9、and alignedin an arc within the area not embossed provided on the lower obverse side. Numbers shall be filled with chip number 26 black enamel. 7. A full forcer shall be used to bring up the details of the design . CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with,respect to the previous issue due to the extent of the changes. Custodian: Army - IH Preparing activity: Army - IH Review activities: DLA - CT (Project NO. 8455-0866) 2 of 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-