ARMY MIL-DTL-14824 C (3)-2008 PROJECTILE 155MM HE METAL PARTS ASSEMBLY M107《155毫米HE炮弹的金属零件组件M107》.pdf
《ARMY MIL-DTL-14824 C (3)-2008 PROJECTILE 155MM HE METAL PARTS ASSEMBLY M107《155毫米HE炮弹的金属零件组件M107》.pdf》由会员分享,可在线阅读,更多相关《ARMY MIL-DTL-14824 C (3)-2008 PROJECTILE 155MM HE METAL PARTS ASSEMBLY M107《155毫米HE炮弹的金属零件组件M107》.pdf(32页珍藏版)》请在麦多课文档分享上搜索。
1、 INCH-POUND MIL-DTL-14824C(AR) w/AMENDMENT 3 5 September 2008 SUPERSEDING MIL-DTL-14824C(AR) w/AMENDMENT 2 27 March 2008 DETAIL SPECIFICATION PROJECTILE 155MM, HE, METAL PARTS ASSEMBLY, M107 This specification is approved for use by the U.S. Army Armament Research Development and Engineering Center
2、(ARDEC), and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers requirements for the manufacturing and assembly of the metal parts for Projectile, 155MM, HE, M107 (see 6.1). AMSC N/A FSC 1320 DISTRIBUTION STATEMENT A. Appr
3、oved for public release; distribution is unlimited. Comments, suggestions, or questions on this document should be addressed to the Commander, U.S. Army ARDEC, ATTN: AMSRD-AAR-QES-E, Picatinny, NJ 07806-5000 or emailed to ardecstdznconus.army.mil. Since contact information can change, you may want t
4、o verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. Inactive for new design after 3 February 1997 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14824C(AR) w/Amendment 3 22. APPLIC
5、ABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made t
6、o assure the completeness of this list, document users are cautioned that they must meet all requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards and handbooks. The following specifications,
7、standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. FEDERAL SPECIFICATIONS TT-C-490 - Chemical Conversion Coatings and Pretreatments for Ferrous Surfaces (Base
8、for Organic Coatings) DEPARTMENT OF DEFENSE STANDARDS MIL-STD-1168 - Ammunition Lot Numbering and Ammunition Data Card MIL-STD-1916 - DoD Preferred Methods for Acceptance of Product (Unless otherwise indicated, Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/
9、or http:/assist.daps.dla.mil from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings and publications. The following other Government documents, drawings and publications form a part of this document to t
10、he extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation or contract. US ARMY ARMAMENT RESEARCH, DEVELOPMENT AND ENGINEERING CENTER (ARDEC) DRAWINGS 10535925 - Projectile, 155MM, HE, M107 Metal Parts Assembly Provided by IHSNot for ResaleNo reproduction
11、or networking permitted without license from IHS-,-,-MIL-DTL-14824C(AR) w/Amendment 3 310535926 Body Assembly 10535927 Body 7548993 - Blank, Rotating Band 9280419 - Envelope Drawing, Ultrasonic Inspection Equipment, 155MM, M107 9280420 - Ultrasonic Test Calibration Standard 155MM, M107 Projectile 92
12、80429 - Rotating Band Seat Tester. (Copies of these drawings may be requested online at Pica.drawing.requestconus.army.mil or from U.S. Army ARDEC, ATTN: AMSRD-AAR-AIS-TD, Picatinny, NJ 07806-5000.) 2.3 Non-Government Publications. The following documents form a part of this document to the extent s
13、pecified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. ASTM INTERNATIONAL (ASTM) ASTM B117 - Standard Practice for Operating Salt Spray (Fog) Apparatus ASTM E8 - Standard Test Method for Tension Testing of Metallic Materials ASTM E
14、10 - Standard Test Method for Brinell hardness of Metallic Materials ASTM E103 - Standard Test Method for Rapid Indentation Hardness Testing of Metallic Materials (Copies of ASTM standards are available online at http:/www.astm.org or from American Society for Testing and materials, 100 Barr Harbor
15、Drive, West Conshohocken, PA 19428-2959) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific
16、exemption has been obtained. 3. REQUIREMENTS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14824C(AR) w/Amendment 3 43.1 First article inspection. When specified(see 6.2) a sample shall be subjected to first article inspection in accordance
17、 with 4.2. 3.2 Components and assemblies. The components and assemblies shall comply with all requirements specified on drawing 10535925. 3.2.1 Body prior to nosing. The materials, components and assemblies shall be in accordance with dwg. 10535927. 3.2.2 Body Machined (prior to band seat machining
18、and threading nose). The materials, components and assemblies shall be in accordance with dwg. 10535927. 3.2.3 Body. The materials, components and assemblies shall be in accordance with dwg. 10535927. 3.2.4 Body Assembly. The materials, components and assemblies shall be in accordance with dwg. 1053
19、5926. 3.2.5 Projectile, HE, 155MM,M107 Metal Parts Assy. The materials, components and assemblies shall be in accordance with dwg. 10535925. 3.2.6 Projectile, 155MM, HE, M107 Metal Parts Assembly Destructive Lot Acceptance. The materials, components and assemblies shall be in accordance with dwg. 10
20、535925. 3.3 Ammunition lot numbering. Ammunition lot numbers shall be assigned in accordance with MIL-STD-1168. 3.4 Mechanical properties. Heat treatment or stress relief applied shall be uniform throughout each lot of projectiles and shall be so performed and controlled as to produce in the project
21、ile the mechanical properties specified in 10535927. 3.4.1 Rotating Band. After application and subsequent removal the rotating band shall have the following mechanical properties: a.Tensile Strength -30,000 lbs per square inch (PSI) minimum b. Elongation 25 percent in one inch of gage length, minim
22、um 3.5 Projectile material defects. 3.5.1 Projectile cavity. The projectile cavity shall be free from scale, fins, burrs, draw marks, laminations, imbedded foreign matter and pits. Surface discontinuities which have a fillet or corner radius smaller than .03 inch shall be rejected. (see 6.5). Provid
23、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14824C(AR) w/Amendment 3 53.5.2 Projectile. The Projectile, including the cavity, shall be free from cracks, splits, bursts, cold shuts, pipe, porosity, inclusions, folds, seams, and other metal defec
24、ts. 3.6 Rotating band. 3.6.1 Foreign matter on band seat. Prior to banding, the band seat shall be free from oil, grease, dirt, rust or other foreign matter. 3.6.2 Application. 3.6.2.1 Destructive. The rotating band shall be applied after final heat treatment of the body, by carefully pressing the b
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ARMYMILDTL14824C32008PROJECTILE155MMHEMETALPARTSASSEMBLYM107155 毫米 HE 炮弹 金属 零件 组件 M107PDF
链接地址:http://www.mydoc123.com/p-443432.html