ARMY MIL-DTL-11589 140 E-2010 RIBBON SUPERIOR CADET AWARD ROTC (JUNIOR DIVISION)《勋表 预备役军官训练营(ROTC)(初级部)优秀学生奖》.pdf

《ARMY MIL-DTL-11589 140 E-2010 RIBBON SUPERIOR CADET AWARD ROTC (JUNIOR DIVISION)《勋表 预备役军官训练营(ROTC)(初级部)优秀学生奖》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-11589 140 E-2010 RIBBON SUPERIOR CADET AWARD ROTC (JUNIOR DIVISION)《勋表 预备役军官训练营(ROTC)(初级部)优秀学生奖》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A Page 1 of 2 FSC 8455 DETAIL SPECIFICATION SHEET RIBBON, SUPERIOR CADET AWARD, ROTC (JUNIOR DIVISION) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specifi

2、cation sheet and the latest issue of MIL-DTL-11589. RIBBON SIZE: Regular WIDTH: 1-3/8 inches + 1/16 inch - 0 (35.0mm + 1.6mm - 0) TOTAL WARP ENDS (Minimum): 448 PICKS PER INCH (Minimum): 40 (2 threads single shot) WEIGHT PER LINEAR YARD: 0.0175 pound LINEAR BREAKING STRENGTH FULL WIDTH (Minimum): 10

3、0 pounds COLOR PATTERN: REGULAR SIZE FINISH: MOIR TOTAL WIDTH OF STRIPES FUNCTION COLOR & CABLE NUMBER WIDTH INCHES & METRIC OF STRIPES STRIPES FILLING YARN 3/16 4.8mm * See Note Below White HA 67101 Scarlet HL 67111 1-3/8” White 1 25.4mm Solid Ground Ultramarine Blue HS 67118 (35.0mm) HA 67101 3/16

4、 4.8mm * See Note Below White HA 67101 Scarlet HL 67111 *NOTE: The warp and horizontal stripes shall be alternating, one (1) White HA 67101 end and one (1) Scarlet HL 67111 end throughout. The weave for the White HA 67101 and Scarlet HL 67111 will be 3/3 resulting in five (5) alternate White HA 6710

5、1 and Scarlet HL 67111 stripes in each 3/8 inch (9.5mm) length of ribbon. The selvage shall have a catch cord for firmness, designed so as to eliminate any looping of the filling yarn. The color of the catch cord shall be White HA 67101. INCH-POUND MIL-DTL-11589/140E 9 June 2010 SUPERSEDING MIL-DTL-

6、11589/140D 15 September 1995 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-11589/140E Page 2 of 2 CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous issu

7、e were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and rela

8、tionship to the last previous issue. Custodian: Preparing activity: Army - IH Army - IH Review activity: (Project No. 8455-2010-291) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-