ARMY MIL-DTL-11484 26 E-2008 LAPEL BUTTON CAPTAIN ROBERT DEXTER CONRAD AWARD FOR SCIENTIFIC ACHIEVEMENT NAVY《海军罗伯特·德克斯特·康拉德(ROBERT DEXTER CONRAD)舰长科研成就襟章》.pdf

《ARMY MIL-DTL-11484 26 E-2008 LAPEL BUTTON CAPTAIN ROBERT DEXTER CONRAD AWARD FOR SCIENTIFIC ACHIEVEMENT NAVY《海军罗伯特·德克斯特·康拉德(ROBERT DEXTER CONRAD)舰长科研成就襟章》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-11484 26 E-2008 LAPEL BUTTON CAPTAIN ROBERT DEXTER CONRAD AWARD FOR SCIENTIFIC ACHIEVEMENT NAVY《海军罗伯特·德克斯特·康拉德(ROBERT DEXTER CONRAD)舰长科研成就襟章》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND MIL-DTL-11484/26E 29 August 2008 SUPERSEDING MIL-DTL-11484/26D 27 September 1996 DETAIL SPECIFICATION SHEET LAPEL BUTTON, CAPTAIN ROBERT DEXTER CONRAD AWARD FOR SCIENTIFIC ACHIEVEMENT, NAVY This specification is approved for use by all Departments and Agencies of the Department of Defense

2、. The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-11484. MATERIAL: Gilding Medal DIMENSIONS: HEIGHT (overall): 9/64 inch (REF) WIDTH (overall): 21/32 inch (REF) THICKNESS (at edge): 0.065 inch + 0.005 inch FINISH:

3、Hard Enameled, Gold Plated, Mirror-like Polished and shall match The Institute of Heraldry (TIOH) Metal Finish Chip Number 6. AMSC N/A Page 1 of 2 FSC 8455 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-11484/26E Page 2 of 2 NOTES: 1. The te

4、rm (REF) refers to the measurements taken from the Government furnished hub or die. 2. Enameled/epoxied areas shall be as shown. Epoxy resin (stoning epoxy) may be at the option of the manufacturer. When hard enamel is used, the material requirement shall be gilding metal. When epoxy is used, the ma

5、terial requirement shall be either red brass or gilding material. Colors shall conform to TIOH Hard Enamel Color Chip Numbers listed below: COLOR CHIP NO. Yellow 8 Blue 20 White 28 3. Attaching device shall be prong with pick and wing type clutch. The prong shall be centered on the reverse side and

6、fused or soldered to the lapel button. CHANGES FROM PREVIOUS ISSUE: The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracie

7、s in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodian: Preparing activity: Army - IH Army - IH Navy NU (Project No. 8455-2008-

8、167) Review activities: DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-