ARMY MIL-DTL-11132 26 H-2013 INSIGNIA GRADE CADET STAFF SERGEANT JROTC U S AIR FORCE.pdf

《ARMY MIL-DTL-11132 26 H-2013 INSIGNIA GRADE CADET STAFF SERGEANT JROTC U S AIR FORCE.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-DTL-11132 26 H-2013 INSIGNIA GRADE CADET STAFF SERGEANT JROTC U S AIR FORCE.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A Page 1 of 3 FSC 8455 INCH - POUND MIL-DTL-11132/26H 4 March 2013 SUPERSEDING MIL-DTL-11132/26G 20 November 1998 DETAIL SPECIFICATION SHEET INSIGNIA, GRADE, CADET, STAFF SERGEANT JROTC, U.S. AIR FORCE This specification is approved for use by all Departments and Agencies of the Department o

2、f Defense The requirements for acquiring the product described herein shall consist of this specification sheet and the latest issue of MIL-DTL-11132. MATERIAL: Red Brass 85/15 (UNS Alloy No. C-230) FINISH: BASE: Epoxy resin (Stoning epoxy), Nickel Plated, Mirror-like Polished and shall match The In

3、stitute of Heraldry (TIOH) Metal Finish Chip Number 16. DEVICE: Epoxy resin, 24K Gold Plated, Mirror-like Polished and shall match TIOH Metal Chip Number 6. DIMENSIONS: BASE: HEIGHT (Overall): 15/16 inch (REF) WIDTH (Overall): 1-1/16 inches (REF) THICKNESS (Edge): 0.065 inch + 0.005 inch Provided by

4、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-11132/26H Page 2 of 3 DEVICE: HEIGHT (Overall): 1/2 inch (REF) WIDTH (Overall): 1/8 inch (REF) THICKNESS (Edge): 0.085 inch + 0.005 inch ASSEMBLED (Thickest Point): 0.150 inch + 0.010 inch EPOXY: Epoxy res

5、in shall be applied to the insignia grade as indicated above, and shall match TIOH Hard Enamel Color Chip Numbers listed below. Hard cloisonn enamel may be used in lieu of epoxy. If hard cloisonn enamel is used, the required base material shall be Gilding Metal 95/5 (UNS Alloy C-210). TIOH HARD ENAM

6、EL COLOR CHIPS COLOR CHIP NUMBER Blue #18 Red #1 Light Blue #30 ATTACHING DEVICE: 1. The device shall be secured to the base by two solid brass rivets 0.035 inch minimum in diameter located on the vertical center line of the device. 2. Attaching device shall be prong and clutch type. 3. Prongs shall

7、 be attached on the horizontal center line, equidistant from each side and 7/8 inch + 1/32 inch apart. NOTES: 1. The term (REF) refers to the measurements taken from the obverse Government furnished hub or die. 2. The base may be rhodium plated with mirror-like polished finish at the option of the m

8、anufacturer. 3. Acid test for the gold plated device shall not apply. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking perm

9、itted without license from IHS-,-,-MIL-DTL-11132/26H Page 3 of 3 Custodians: Preparing activity: Army - IH Army - IH Air Force - 11 Review activity: (Project No. 8455-2013-128) DLA - CT NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-