ARMY MIL-C-70734-1987 CONTAINER AMMUNITION METAL PA113 FOR CANISTER VOLCANO MINE M87 M88《M87 M88火山地雷用PA113型金属弹药集装箱》.pdf

《ARMY MIL-C-70734-1987 CONTAINER AMMUNITION METAL PA113 FOR CANISTER VOLCANO MINE M87 M88《M87 M88火山地雷用PA113型金属弹药集装箱》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-70734-1987 CONTAINER AMMUNITION METAL PA113 FOR CANISTER VOLCANO MINE M87 M88《M87 M88火山地雷用PA113型金属弹药集装箱》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-70734 (AR) 6 October 1987 NIE I TARY SPEC TFI CATI ON CONTAINER, AMMUNITION, METAL, PA113, FOR CANISTER, . VOLCANO MINE M87/M88 This specification is approved for use within the U.S. Army Armament Muiiitions anCi Chemical Command (AMCCOM) , and is available foi: use by all Departments and Agen

2、cies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements, quality assurance provisions and packaging for one type of metal container used for M87/M88 VOLCANO Mine Canisters. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and stanards.

3、The following specifications and standards form a part of this specification to the extent specified herein, Unless otherwise specified, the issues of these documents shall be those listed in the issues of the Department of Defense Index of Specifications and Standards CDoDISS) and supplement theret

4、o, cited in the solicitation. SPECIFICATIONS FEDERAL TT-C-490 -Cleaning Methods for Ferrous Surfaces and pretreatments for Organic Coatings. MIL I TARY MIL -W- 12 3 3 2 -Welding Resistance, Spot, Seam and Proauction, for Fabricating Assemblies of Low-Carbon Steel MIL-A-48078 -Ammuni tion, Standard Q

5、uality Assurance Provisions, General Specification For Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in Improving this document should be addressed to: Commander, U.S. Army Armament,Munitions and Chemical Command, Attn. AMSMC-QA. Picatinny Ars

6、enal, New Jersey 07806-5000 by using the self-addressed Standardiza- tion Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FCC 8140 DISTRIBUTION STATEMENT A. #on is n-imi ted . -_- THIS DOCUMENT CONTAINS 30 PAGES. - i - -_ -c_ - - cl Licensed

7、by Information Handling ServicesMIL-C-70734 1 W 9777706 0289525 5 W 9 ,S MIL-C-70734 (AR) STANDARDS MILITARY MIL -STD- 1 O 5 -Sampling Procedures and Tables for MIL-STD- 171 -Finishing of Metal and Wood MIL-STD- 119 O -Minimum Guidelines for Level C Preservation, MIL-STD- 12 3 5 Inspect ion by At t

8、r i butes Surf aces Packing, and Mar king Procedures and Table for Inspection by Attributes. -Single-and-Multi Level Continuous Sampling 2.1.2 Other Government documents, drawings, and publications, The following other Government documents, drawings, and publications form a part of this specificatio

9、n to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. DRAWINGS (see 6.3) US ARMY ARMAMENT RESEARCH, DEVELOPMENT AND ENGINEERING CENTER (ARDEC) 9390404 -Container, Ammo, Metal, PA113, for Canister Mine: M87 and Canister Mine

10、, Practice: M88 (Copies of specifications, standards, handbooks, drawings, publications and other Government documents required by contractors in connections with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity). 2.2 Other pu

11、blications. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues o

12、f documents not listed in the DODISS shall be the issue of the nongovernment documents which is current on the date of the solicitation. Licensed by Information Handling ServicesMIL-C-70734 81 9999906 0289526 7 = ?-+- Tz: 9 a MIL-C-70734 (AR) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM-D4

13、 12 ASTM-D2240 ASTM-E8 ASTM-E18 (Application for copies should be -Rubber Properties in Tension, Test Methods for -Rubber Property-Durometer Hardness, Test Method for -Tension Testing of Metallic Materials, Standard Method of -Rockwell Hardness and Rockwell Superficial Hardness of Metallic Materials

14、, Test for addressed to the American Society for: Testing and Materials, 1916 Race Street, Philadelphia, PA the text f this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall. supersede applicable laws an

15、d regulations unless a specific exemption has been obtained. 19103) 2.3 Order of precedence. In the event of a conflict between 3. REQUIREMENTS 3.1 Materials. Materials and parts shall be in accordance with 3.2 Containezs. The containers shall comply with all applicable drawings and specifications.

16、requirements specified on drawing 9390404 and associated drawinss and with all requirements specified in applicable specifications and standards. 3.3 Welding. The welding shall comply with the requirements of MIL-W-12332. 3.3.1 Tensile strength. When tested as specified in 4.5.1, the tensile strengt

17、h of the body material shall be in accordance with .drawing 12630901 and the tensile strength of the longitudinal body weld shall be not less than 65 percent of the tensile strength of body material. 3.4 Painted surface. The painted surface of the container shall comply with the requirements of TT-6

18、-490. However, the film thickness and salt spray requirements of TT-C-490 shall not apply to the interior surfaces, welded spots, sharp corners and crevices of the exterior surface of the container. Bare spots permissible on all bearing cur f aces . 3 Licensed by Information Handling Services-_ - _

19、- 2 I. * MIL-C-70734 81 m 7777706 0287527 7 m MIL-C-70734 (AR) 3.5 Cover assembly. Upon assembly of the cover assembly to the body weldment (body assembly) , the cover assembly shall freely engage and rotate within the body wedment. is rotated with the iiYi handle in the open position, the “Y“ handl

20、e shaft ends shal freely engage into the respective bayonet slots of the rim. When the “Y“ handle is in the closed position (rotated 1800), the spring clip shall engage and lock the handle in place and a 0.06 inch diameter pin shall pass through the handle and shaft support holes. When the spring cl

21、ip is disengaged and the handle rotated to the open position, the cover assembly shall disengage from the body weldment. or purchase order, a sample shall be subjected to First Article Inspection (see 4.3). As the cover assembly 3.6 First article inspection. When specified in the contract 3.7 Wor km

22、ansli ip. 3.7.1 Containers. The containers shall be regular, smooth, and free from wrinkles, pin holes, cracks, rough spots, burrs, sharp edges and any other defect that might affect the serviceability, durability, safety or appearance of the container. 3.7.2 Paint coating. The paint coating shall b

23、e in accordance with applicable drawings and comply with instructions in MIL-STD-171. 3.7.3 Parts. All parts shall be free of chips, dirt, grease, rust and foreign material. The cieaiiing method used shall not be injurious to any of the parts nor shail any of the parts be contaminated by the cleanin

24、g agents used. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. bxcept as otherwise specified in the contract or purch

25、ase order, the contractor may use his own or any other facilities suitable for the performance 02 the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspecti

26、ons are deemed necessary to assure supplies and services conform to prescribed requirements. Licensed by Information Handling ServicesI_ - - NIL-C-7073V 81 9999906 0289528 O M . . MIL-C-70734 (AR) 4.1.1 Responsibility for compliance. ASS items must meet all requirements of sections 3 and 5. Theinspe

27、ction set forth in this specification shall become a part of the contractors overall inspection system or quality program. requirements in this specification shall not relieve the. contractor of the responsibility of assuring that all products or supplies submitted to the Government ?sr acceptance c

28、omply with all requirements of the contract- Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. The absence of any inspection 4.2 Classification of inspections.

29、The following types of - -_I inspection shall be conducted on this item: a. First article inspection. (see 4.3) b. Quality conformance inspection. (see 4.4) 4,3 First article inspection. 4.3.1 Submission. The contractor shall submit a first article sample as designated by the Contracting Officer for

30、 evaluation in accordance with provisions of 4.3.2. be in accordance with Table I. The first article sample shall 4.3.2 Inspections to be performed. See MIL-A-48078 and Table I specified herein. 4.3.3 Rejection. See MIL-A-48078. - . 5 Licensed by Information Handling Servicescu dIJ E oi MIL-C-70734

31、81 m 779970b 0287527 2 m rn in rl rl cu cv(v di dim -Y *-Y I . . I. . O M rl rl rl curl cum cu di -Fin dim di die didi . . cu (vcu NN m mm M mm mm * . cu NN .I O O O in rlm in din rlM 6 Licensed by Information Handling ServicesiiL-C-70734 81 m 797770b 0287530 7 i P 4J 111 & .rl h N 8 N E B rn .U C a

32、l c O c4 U 5 C (d m al .rt 4 a 111 U1 .-E $ 4 Y. a_ c si. a,Kl a, 7 Licensed by Information Handling Servicesl_ - - MIL-C-7073LI 81 a 797990b 0289531 O a MIL-C-70734 (AR) 4.4 Qualit2 - - -.- - conformance I- - wII- inspection. 4.4.1 inspection - lot formation. inspection lots shall comply with the l

33、ot formation provisions of MIL-A-48078. inspection lots of containers shall contain material from lots with the same interfix number from one manufacturer. 4.4.2 Examination. See MIL-A-48078. Unless otherwise specified in the Classification of Deects and Test Tables, sampling plans and procedures fo

34、r major and minor defects shall. be in accordance with MIL-STD-105, Inspection Level. II. Continuously sampling plan in accordance with MIL-STD-1235 may be used if approved by the Government. In addition, 8 Licensed by Information Handling Servicese k P H 2 8 - MIL-C-70734 81 m 9999306 0289532 2 m r

35、l 8 rl E H m C I :pi -KI 8 E x Erl i“ ttainted =$gbneb- assembly. Subject the container assembly te, %he interrial air pressure, specified in the applicable containeic assembly drawing, for one of the test times specified. Observation shall be made for any evidence of leakage exceeding the requireme

36、nt for the corresponding test time (as specified in %he applicable dlraving) A container assembly, whish exceeds the requiemen%, shall be classed defective. 4.5.7.2 -emiyofxinted cpntainer assemblies. Randomly interchange th cover assemblies with container body weldments while positioning %he cover

37、assembly in a random orientation and perform the air PKSSU test DE 4.5.7.1. Failure to meet ihe applicable reguiremnt shail be cause for rejection of the 1o.fi. 4.5.8 Covermetest. Upon assembly of the body weldment and cover assembly, the cover shall freely engage and - rotate wikhin the body we%dme

38、n%. The Y-handle shaft ends shall engage into the respective bayonet slots of the rim without interference an a (3.06 inch diameter pin shall pass through the cover assembly holes when in the clamping position. The spring clip shal engage and Lock the handle when in this position. The Y-handle, when

39、 disengaged and in the open position, shall Cisengage the COVK from the body. Any assembly which fails to meet: this ci-iteria shall be classed defective. 4.5.9 -que task. The minimum applicable torque shall be applied to the SCKW. Any evidence of motion of the screw before reaching the minimum acce

40、ptable torque shall be cause for rejection of the container assembly being teated. Any container assembly whish fails the screw %orque teat may be reworked and returned to the lot after passing the screw torque test. 2“ -=e- 1_1_ Licensed by Information Handling Services- MIL-C-70734 81 777970b 0287

41、553 T s MIL-C-70734 5. PACKAGING 5.1 Packaging requirements. None required. 5.2 Packing. Packing shail be Level C. Metal ammunition containers and components shall be prepared in accordance with the requirements of MIL-STD-1190. 5.3 Marking. Shipping marking shall comply with MIL-STD-1190 and the fo

42、llowing additional instructions. No shipping marking shall be placed directly on the containers. Commercial shipping tags attached with wire shall be used on the containers unless otherwise specified. The following information shall be shown: Item name and model number (if applicable), part number a

43、nd revision, contract number, lot number and date, name and address of manufacturer. If containers or components are bundled, boxed or palletized, the gross weight and quantity shall be included. The above information may be placed on pallets or boxes by labeling or stenciling . 6. NOTES 6.1 Intende

44、d use. The container is intended for use in the M87/M88 VOLCANO Mine Canister. 6.2 Orderinq data. See MIL-A-48078. 6.3 Drawings. Drawings listed in Section 2 of this specification under the heading US Army Armament Research, Development and Engineering Center (ARDEC) may also include drawings prepar

45、ed by and identified as US Army Armament Research and Development Command (ARRADCOM), Edgewood-Arsenal, Frankford Arsenal, Rock Island Arsenal or Picatinny Arsenal drawings. Technical data originally prepared by these activities is now under the cognizance ARDEC. 6.4 Submission of inspection equipme

46、nt design for approvals. See MIL-A-48078. Submit designs as required to: Commander, US Army Armament Research, Development and Engineering Center (ARDEC), ATTN: AMSMC-QAT-I, Picatinny Arsenal, New Jersey 07806-5000. This address will be specified on the Contract Data Requirements List, DD Form 1423.

47、 Unless otherwise specified, data item DI-R-1714 will apply. 6.5 Subject term (key word) listinq. Ammunition Mine Can ist er Container Metal * U.S. GOVERNMENT PRINTING OFFICE: 1987-505-033/75758 Cu st od i an : Army-AR Preparing activity: ( Pro j ec t 814 O -A7 50 ) Army-AR i : 30 Licensed by Information Handling Services