ARMY MIL-C-70509 (5)-1993 CARTRIDGE 9MM TEST HIGH PRESSURE XM905《XM882型9MM测试高压炮弹》.pdf

《ARMY MIL-C-70509 (5)-1993 CARTRIDGE 9MM TEST HIGH PRESSURE XM905《XM882型9MM测试高压炮弹》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-70509 (5)-1993 CARTRIDGE 9MM TEST HIGH PRESSURE XM905《XM882型9MM测试高压炮弹》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-70509 (5) 9999906 L854L20 538 I INCH-POUND I MIL-C-70509 (AR) AMENDMENT 5 18 IlARCH 1993 SUPERSEDING AMENDMENT 4 5 April 1991 MILITARY SPECIFICATION CARTRIDGE, 9MM, TEST, HIGH PRESSURE, XM905 This Amendment forms a part of MIL-C-70509(AR), dated 7 February 1985, and is approved for use by the

2、US Army Armament, Munitions and Chemical Command and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 Title: Add, (M905 ) II after 11XM90511. 1.1, Last line: Add II(M905)“ after 11XM90511. PAGE 2 0 Delete paragraph number 112. 2. lV1 and Substitute It2. 1.2“.

3、 2.2.1, under Drawing 9378265: Add I(M905)“ after “XM90511. 2.2.1, Delete: “9378266 - packaging and Marking, Cartridges, 9mm, Test, High Pressure, XM905, Cartons, Box, Ammunition, M2A1, Box Wirebound“ and substitute, “9396206 - Packing and Marking for Box, Wirebound, for Cartridges, Small Caliber1.

4、PAGE 3 Delete paragraph I13.6l1 in its entirety and substitute: “3.6 Chamber pressure. The average peak chamber pressure at the mid-case position shall be 48,000 pounds per square inch (psi) plus or minus 2,500 psi when conditioned and fired at +70F. not exceed 3,200 psi. +lOOF, the average peak cha

5、mber pressure at each temperature shall not vary by more than plus or minus 3,000 psi from the average pressure obtained at +70F. I The standard deviation of the chamber pressure shall When conditioned and fired at +32F and AMSC N/A FSC 1305 1 of 2 DISTRIBUTION STATEMENT A. Approved for public relea

6、se; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-e MIL-C-70507 (5) = 7777706 3854121 474 MIL-C-70509(AR) AMENDMENT 5 PAGE 7 4.4.2.1: * Delete: “3. No primer 100% 3.3 Visual 4. Cocked primer 100% 3.3 Visual 5. Inverted pr

7、imer 100% 3.3 Vi sua1 Add under llCRITICALtl : “3. Minimum propellant levei 100% 3.3 Gage“ (Dwg. 9345211, Note 4) Add after critical defects: * “SPECIAL: a. No primer 100% 3.3 Visual b. Cocked primer 100% 3.3 Visual C. Inverted primer 100% 3.3 Visual“ PAGE 12 4.5.4: Add “Section 12“ to the end of th

8、e sentence. The marqins of this amendment are marked with an asterisk or vertical line to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and c

9、ontractors are cautioned to evaluate the requirements of this document based on the entire This was done as a convenince only and the content irrespective of the marginal notations and relationship to the last previous amendment. Custodian : Army-AR Preparing activity: Army-AR ( Proj ect 1305-AE58 ) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-