ARMY MIL-C-63063 (3)-1999 CASE CARTRIDGE 40MM M169 PLUG BASE FOR [Superseded ARMY MIL-DTL-60982 E CONT DIST ARMY MIL-DTL-60982 D (1) CONT DIST ARMY MIL-DTL-60982 D CONT DIST ARM.pdf

《ARMY MIL-C-63063 (3)-1999 CASE CARTRIDGE 40MM M169 PLUG BASE FOR [Superseded ARMY MIL-DTL-60982 E CONT DIST ARMY MIL-DTL-60982 D (1) CONT DIST ARMY MIL-DTL-60982 D CONT DIST ARM.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-63063 (3)-1999 CASE CARTRIDGE 40MM M169 PLUG BASE FOR [Superseded ARMY MIL-DTL-60982 E CONT DIST ARMY MIL-DTL-60982 D (1) CONT DIST ARMY MIL-DTL-60982 D CONT DIST ARM.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、I 9999906 2334954 ObT I INCH - POUND MIL-C-63063 (AR) AMENDMENT 3 10 August 1999- SUPERSEDING AMENDMENT 2 10 November 1992 MILITARY SPECIFICATION CASE, CARTRIDGE, 40MM, M169; PLUG, BASE FOR MIL-C-63063 was inactivated after 12 February 1996 for new design. 1 This amendment forms a part of Military S

2、pecification MIL-C-63063(AR), dated 29 March 1976, and is approved for use by the US Army Armament Research And Development Center (ARDEC) and is available for use by all Departments and Agencies of the Department of Defense. PAGE 2 Delete “DRAWINGS, PICATINNY ARSENAL“ and substitute the following:

3、“DRAWINGS (See 6.5) U.S. ARMY ARMAMENT RESEARCH AND DEVELOPMENT COMMAND“ * Delete Inspection Equipment Drawings section in its entirety. PAGE 6 * 4.4.2.1, Defects 1, 103 and 104 - under Inspection Method, change “Automatic tidye (9202532) “ “8841561“ to read “Gage“ in three (3) places. 4.4.2.1, Dele

4、te defect characteristics “Majors 107 and 108“ in their entirety and substitute the following: “MAJOR 107. Location of small loa. Location of large datum diameter O. 40% 3.2 datum diameter O. 40% 3.2 PAGE a 4.5.1 Change from: “This test shall be conducted for 240 hours.“ to: “This test shall be cond

5、ucted for 72 hours.“ Gage Gage“ AMSC N/A 1 of 2 FSC 1310 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited Licensed by Information Handling ServicesMI L-C- 6 3 O 63 (AR) AMENDMENT 3 6.3, Delete “SARPA-QA-TI Picatinny Arsenal“ and substitute “SMCAR-QAF-I, ARDEC“ . 6.4,

6、Delete “Picatinny Arsenal, ATTN: SARPA-QA-A-S“ and substitute “ARDEC, Dover, N J 07 8 O 6 , ATTN : SMCAR-QAF-S“ . 6.5, Add the following“ “6.5 Drawings. Drawings listed in Section 2 of this specification under the heading US Army Armament Research and Development Command (ARRADCOM) may also include

7、drawings prepared by and identified as, Edgewood Arsenal, Frankford Arsenal, Rock Island Arsenal or Picatinny Arsenal drawings. Technical data originally prepared by these activities is now under cognizance of ARDEC.“ The margins of this amendment are marked with an asterisk or vertical lines to ind

8、icate where changes (additions, modifications, corrections, deletions) from the.previous amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Custodian: Army- AR Preparing activity: Army-AR (Project 1310-0591) 2 Licensed by Information Handling Services