ARMY MIL-C-53057-1985 CONTAINER CRANE ROUGH TERRAIN WHEEL-MOUNTED HYDRAULIC DIESEL-POWERED《柴油动力液压轮式安装崎岖地形集装箱起重机》.pdf

《ARMY MIL-C-53057-1985 CONTAINER CRANE ROUGH TERRAIN WHEEL-MOUNTED HYDRAULIC DIESEL-POWERED《柴油动力液压轮式安装崎岖地形集装箱起重机》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-53057-1985 CONTAINER CRANE ROUGH TERRAIN WHEEL-MOUNTED HYDRAULIC DIESEL-POWERED《柴油动力液压轮式安装崎岖地形集装箱起重机》.pdf（98页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-53057 37 W 9777706 0287803 8 -1 p- 3-P MIL-C-53057(ME) 24 July 1985 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Belvoir Research and Development Center, ATTN: STRBE-DS, Fort Belvoir, V

2、A 22060-5606 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. USA MILITARY SPECIFICATION CONTAINER CRANE, ROUGH TERRAIN, WHEEL-MOUNTED, HYDRAULIC, DIESEL-POWERED This specification is approved for use by the

3、USA Belvoir Research and Development Center, Department of the Amy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for diesel-engine- driven, four-wheel drive, wheel-mounted, rough terrain, pneumat

4、ic-tired, hydraulic container cranes. 2. APPLICABLE DOCUMENTS 1 .- 2.1 Government documents. 2.L.1 Specifications and standards. Unless otherwise specified (see 6.21, the following specifications and standards of the issue listed in that issue of the Department of Defense Index of Specifications and

5、 Standards (DODISSI specified in the solicitation, form a part of this specification to the extent specified herein, SPECIFICATIONS FEDERAL GG-P-455 QQ-P-35 TT-C-494 RR-W-4 1 O - Plates and Foils, Photographic (Photo- sensitive Anodized Aluminum. - Passivation Treatments for Corrosion Resisting Stee

6、ls. - Coating Compound, Bituminous, Solvent Type, Acid Resistant. - Wire rope and strand. DISTRIBUTION STATEMENT A. unlimited. Approved for public release; distribution is K THIS DOCUMENT CONTAINS -qp .- PAGES Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

7、IHS-,-,- MIL-C-53057 33 W 9993906 028780Li T W MILITARY MIL-V-193 MIL-P-514 MIL-T-IO4 MIL-C-1283 MIL-L-2104 MIL-G-3859 MIL-P-14105 BOD-P-24555 MIL-C-40626 MIL-S-43926 MIL-G-43976 HIL-F-43989 MIL-A-46153 M IL-L-46 16 7 MIL-C-46168 MIL-B-46176 M IL-M-5 1 2 8 2 MIL-H-51291 MIL-P-52192 MIL-A-52363 MIL-H

8、-52471 MIL-E-52649 MIL-P-52723 MIL-P-5 303 O MIL-C-53039 MIL-T-62324 - Varnish, Moisture-and-Fungus Resistant (For Treatment of Communications, Electronic, and Associated Equipment). - Plates, Identification, Instruction and Marking, Blank. - Treatment and Painting of Materiel. - Can, Gasoline, Mili

9、tary, 5-Gallon. - Lubricating Oil, Internal Cornbustion - Grease Guns, Hand-Operated, Lever, - Paint, Heat Resistant (for Steel Surface). - Paint, Aluminum Heat Resisting (650“ CI, Low - Sign Kit, Vehicle Class. - Suit, Chemical Protective. - Glove Set, Chemical Protective. - Footwear Cover, Chemica

10、l Protective (Overboots) . - Antifreeze, Ethylene Glycol, Inhibited, Heavy Duty, Single Package. - Lubricating Oil, Internal Combustion Engine, Arctic. - Coating, Aliphatic Polyurethane, Chemical Agent Resistant. - Brake Fluid, Silicone, Automotive, All Weather, Operational and Preservative. - Mask,

11、 Chernical - Biological, Field, M17Al. - Hood, Chemical - Biological Mask: M6A2. - Primer, Coating, Epoxy. - Air Cleaners, Intake: Dry-Type (for - Hose and Hose Assemblies, Rubber: Engine, Tactical Service. Push and Screw Type. Emissivity. Internal-Combustion Engine) Hydraulic Pressure-Type, General

12、 Specification for. Primers . - Engine Cold Starting Aids, Ether Fuel - Filter Element, Hydraulic, Disposable. - Primer Coating, Epoxy, Water Reducible, Lead and Chromate Free. - Coating, Aliphatic Polyurethane, Single Component, Chemical Agent Resistant. - Test Equipment (Simplified) for Internal C

13、ombustion Engine (STE/ICE) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDS FEDERAL FED-STD-H28 MILITARY MIL-STD-130 MIL-STD-162 E- I MIL-STD-209 MIL-STD-461 MIL-STD-642 MIL-STD-810 MIL-STD-889 MIL-STD-1366 MIL- S TD- 14 1 O MIL-STD-1474 M

14、S 24207 MS35000 MS 5 1113 MS51117 MS51318 MS51330 MS52125 MS5 2126 MS5 2131 MS 5 305 2 MS500004 MS500048 - Screw Thread Standards For Federal Services. - Identification Marking of US Military Property. - Materials Handling Equipment: Preparation for Shipment, Storage, Cyclic Maintenance, Routine Tes

15、ting and Processing. - Slinging and Tiedown Provisions for Lifting and Tying Down Military Equipment. - Electromagnetic Interference Characteristics Requirements for Equipment. - Ldentification Marking of Combat and Tactical Transport Vehicles. - Environmental Test Methods and Engineering Guidelines

16、. - Dissimilar Metals. - Material Transportation System Dimensional - Methods for Selection of Industrial Engines - Noise Limits for Army Materiel. - Coupling, Grease Gun; Hydraulic Type Nozzle. - Battery, Storage, Lead-Acid, Waterproof. - Switch, Vehicular Lights, 24-Volt DC, Water- - Pintle Assemb

17、ly, Towing: 100,000 Lbs. - Headlight: Blackout, 24 Volt, Waterproof. - Stop Light - Taillight, Vehicular - 24 Volt, - Composite Light - Tail, Stop, Turn and - Composite Light - Front, Turn, Park and - Connector, Plug, Electrical Intervehicle - Bracket Assembly, Liquid Container, Five - Pad Eye Vehic

18、ular Towing Lug. - Towbarb Motor Vehicle, Light, Medium and and Weight Constraints, Definition of. for End Item Application. proof. Capacity, Manual Release. Blackout Tail, Blackout Stop. Marker. Marker. Power Cable. Gallon. Heavy buty. 3 Provided by IHSNot for ResaleNo reproduction or networking pe

19、rmitted without license from IHS-,-,-MIL-C-5305 7 (ME) UNITED STATES DEPARTHENT OF AGRICULTURE (USDA) I MILITARY I I Occupational Safety and Health Administration (OSHA) Standards. MIL-HDBK-I 57 - Transportability Criteria, l aie. indicated as DoD adopted Chal1 be the issue listed in the issue of th

20、e DODICC specified in the solicitation, (Copies of military specifications and military standards required by manufacturere in connection with specific acquisition functions should be obtained from the Naval Publications and Forms Center, 5801 Tabor Avenue, Philadelphia, PA 19120. Military handbooks

21、 should be obtained from the procuring activity or as directed by the contracting officer,) 2.1.2 Other Government: documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein, DRAWIWC TA

22、COM 12258M1 12258955 - Connector, Receptacle 54 Pin. - Vehicle Test: Card. BEPORT CR 82-588-003 - STE/ICE Llesign Guide for Vehicle Diagnostic Connector (Application for copies should be addressed to Department of the Army, U.S. Army Tank-Automotive Command, ATTN: DRSTA-RGD, Warren, MI 48090,) Fores

23、t Service Standard 5190-1. ENVIRONMENTAL PROTECTION AGENCY (EPA) Protection o Environment. Title 40 Code of Federal Regulations. DEPARTMENT OF LABOR (Application or copies should be addressed to the Superintendent of Documents, Government Printing Office, Washington, D.C. 20402,) 2.2 Other publicati

24、ons, The following document(s) form a part of this eueclfication to the extent specified herein, The issues of the documents which 4 -8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-53057 37 m 777770b 0287807 5 MT E-C -5 30 5 7 (ME AMERICAN N

25、ATIONAL STAM)AHDC INSTITUTE, INC. (ANST.) B93.30M Hydraulic Fluid Power - Contamination Analysis Data - Reporting Method . 253.1 Safety Color Code fr Marking Physical Hazards. MH11.3 Load Handling Symbols for Powered Industrial Trucks. 226.1 Safety Glazing Materials for Glazing Motor Vehicles Operat

26、ing un Land Highways. B30,5 Mobil and Locomotive Cranesr (Application for copies should be addressed to the American National Standarde hstitute, Tnc., 1430 Broadway, New York, NY 10018.) AMERICAN SOCIETY FOR TESTING AM, MATERTALS (ASTM) D - 1171 D 3451 Standard Practice for Commercial Packaging. Ru

27、bber Deterioratin i- Surface Ozone Cracking Outdoors or Chamber. - (Application or copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.1 AMERCAN SOCIETY OF MECHANTCAL ENGINEERS (ASME) Boiler and Pressure Vessel Code, Welding Qualific

28、ations, Section IX. (Application for copies should be addressed ta the American Society of Mechanical Engineers, 345 East 47th Street, New York, NY 10017.) AMERICAN WELDING SOCIETY, INC. (AWS) Dl.1 n14.3 - Earthmoving and Construction Equipment Welding, Section 5, - Structural Welding Code, Sections

29、 5 and 6, Welding Qualifications. Qualification. (Application for copies should be addressed to the American Welding Society, Inc. , 2501 N.W. Seventh Street, Miami, FL 33125.) TNDUSTRIAL FASTENERS INSTITUTE (IFI) Standard 114 - Standard for Break Mandrel Blind Rivets. (Application Er copies shuuld

30、be addressed to the Industrial Fasteners Institute, 1517 Terminal Tower, Cleveland, OH 44113,) NATIONAL FLUID POWER ASSOCIATION (NFPA) T.3.9.18 - 1976 - NFPA Recommended Standard for Calibration of Liquid Automatic Particle Counters. 5 Provided by IHSNot for ResaleNo reproduction or networking permi

31、tted without license from IHS-,-,-MIL-C-5 305 7 (ME (Application or copies should be addressed to the National Fluid Power A6OaCiatiOn, P.O. Box 49, “hiensville, WI 53092. POWER CRANE AND SHOmL ASSOCLITION (PCSA) Mebile Hydraulic Crane Standards (PCSA Standard No. 4) (Application for copies should b

32、e addressed to the Power Crane and Shovel Aasociation, Marine Plaza, Suite 1700, 111 E. Wisconsin Ave., Milwaukee, WI 532021 . SOUTH COAST AIR QUALITY MANAGEMENT DISTRICT (SCAQMD) Rute 442 - Usage of Solvents. (Application for copies should be addressed to the South Coast Air Quality Hanagearent Dia

33、trict, 9150 Flair Drive, El Monte, CA 91731.) SOCIETY OF AUTOHOTIVE ENGINEERS (SAE) CAE Handbook. (Application for copies should be addressed to the Society of Automotive Engineers, 400 Cornonwealth Drive, Warrendale, PA 15096.) TIRE AND RIM ASSOCIATION, INC. (TRAI Tire and Rim Aasociation Yearbook.

34、 UppHcation for copies should be addressed to the Tire and Rim Association, Inc., 3200 Weet Market Street, Akron, OH 44313.) (Industry association specifications and standards are generally available for reference from libraries. using Federal agencies . 1 They are also distributed among technical g

35、roups and 2.3 Order of precedence. In the event of a conflict: between the text of this epecification and the references cited in 2.1.1, 2.1.2, and 2.2, the text of thie specification shall take precedence. 3. REQUIRGMEHTS 3.1 Description. The crane shall be four wheel drive, pneumatic tired, diesel

36、 engine driven, whee-mounted, full revolving hydraulic telescoping boom, container crane. The crane shall conform to OSHA, ANSI, and PCSA standards as applicable by the load rating chart for the required radius. 3.1.1 Rated load. Rated load (see 6.8.1) for the crane shall be as specified 6 Provided

37、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-53057 (ME) 3.1.2 Physical characteristics. 3.1.2.1 Weight. With the crane fully fueled and serviced, the axle weight shall not exceed 59,000 pounds for the heaviest axle. weight shall be 111,000 pounds. Ma

38、ximum allowable vehicle 3.1.2.2 Overall height. The overall crane height, with the boom horizontal shall not be more than 13 feet. . 3.1.2.3 Axle spacing. Axle spacing for the crane shall be not less than 12 feet. 3.1.2.4 Width. The width o-f the crane including tire bulge at manufacFurers recommend

39、ed tire pressure shall be not more than 12 feet 6 inches. 3.1.2.5 Ground clearance. The ground clearance and the angles of approach and departure of the crane as defined in SAE 51234 shall not be less than 14 inches and 13 degrees respectively. The crane shall be fully fueled and serviced. The remov

40、al of the outrigger floats are allowed. 3.1.3 Transportability. The crane shall be transportable without damage, by highway, marine, and rail transport modes. Transportability criteria are established by MIL-STD-1366 and MIL-HDBK-157 s described herein. 3.1.3.1 Highway transportability. Disassembly

41、of the crane is acceptable to meet height, width, and weight requirements specified herein. Disassembly shall be accomplished in not more than 12 clock hours, and reassembly of the crane shall be accomplished in not more than 12 clock hours by six persons using suitable material handling equipment a

42、s required. not include cutting or welding. MIL-STD-209 shall be furnished on each assembly, (except tires and wheels), required to be lifted by crane on to the semi-trailer (M747). for highway transport are: Disassembly/assembly shall Slinging and tiedown provisions conforming to The limitations He

43、ight - When mounted on the 44-inch high semi-trailer bed the maximum Width Weight - The maximum payload weight for highway transport shall not exceed height above ground shall not exceed I62 inches. - The maximum width for highway transport shall not exceed 144 inches. 60,000 pounds. 3.1.3.2 Rail tr

44、ansportability. All components removed for highway transport shall also be removed for rail transport. The crane and the removed components shall withstand railroad humping without permanent deformation or damage to any of its components when tested in accordance with MIL-STD-810, Method 516.3, Proc

45、edure VI11 - Rail Impact. 3.1.3.3 Marine transportability. The crane without disassembly, shall be transportable by breakbulk cargo ships, roll-on/roll-off (RORO) ships, C-8 and larger, lighter aboard ship (LASH), barge carrying ships (SEABEE), LARC6O and -7 Provided by IHSNot for ResaleNo reproduct

46、ion or networking permitted without license from IHS-,-,-largar amphibious vessels (LCM-8, LCU-1466, LCU-1646, BDL MARK I, Bk 7001, BC 7005, and BC 231-A) in accordance with MIL-HDBK-157 and MIL-STD-1366. 3.1.4 Crane structure. The structure of the crane shall be such that stresses induced during re

47、quired operations do not exceed the allowable strength margins sf CAE: 51063. 3.2 First article. When specified (see 6.21, 4 or more cranes shall be subjected to first article tests and inspection as specified in section 4. Any changes or deviations of cranes from the- approved first article during

48、production will be subject to the approval of the contracting officer. first article will not relieve the contractor of his obligation to furnish crane8 conforming to this specif ication. Approval of the 3.3 Material. Material shall be as specified herein. Materials not specified shall be selected b

49、y the contractor and shall be subject to all provisions of this specification, practical es long a6 it meets the requirements of this specification (see 6.8.7). It is encouraged that recovered material be used when 3,a.l Dissimilar metals. Dissimilar metals shall not be used in intimate contact: with each other unless suitably protected against electrolytic corrosion. described In MIL-STI)-889. Dissimilar metals and methods of