ARMY MIL-C-52973 A-1987 COMPRESSOR UNIT 20 CFM 5000 PSI DIESEL-ENGINE-DRIVEN DIVING AIR《5000 PSI型20 CFM柴油发动机压缩机组》.pdf

《ARMY MIL-C-52973 A-1987 COMPRESSOR UNIT 20 CFM 5000 PSI DIESEL-ENGINE-DRIVEN DIVING AIR《5000 PSI型20 CFM柴油发动机压缩机组》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-52973 A-1987 COMPRESSOR UNIT 20 CFM 5000 PSI DIESEL-ENGINE-DRIVEN DIVING AIR《5000 PSI型20 CFM柴油发动机压缩机组》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-52973A 43.I 9999906 0277600 T P MIL-C-52973A(ME) 28 September - 1987 SUPERSEDING MIL-C-52973(ME) 8 November 1979 MILITARY SPECIFICATION COMPRESSOR UNIT, 20 CFM, 5000 PSI, DIESEL-ENGINE-DRIVEN DIVING AIR This specification is approved for use within the USA Belvoir Research, Development, and En

2、gineering Center, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 This specification covers a skid-mounted diesel-engine driven, air compressor for producing air suitable for breathing. approved by the Naval Sea Systems Comm

3、and (CODE OOC) (NAVSEA), Alexandria, Virginia are to provide the subject unit. Navy Use, 10 June 1987, NAVSEA Instruction 10560.2, is to be used when procuring the unit and repairlreplacement parts. due to the critical life support nature of the unit. Only commercial vendors The Diving Equipment Aut

4、horized for No variation or substitute is permitted 0 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified,

5、 the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISSI and supplement thereto, cited in the solicitation. Beneficial comments (recommendations, additions, deletions) and. any pertinent data which may be of use in

6、improving this document should be addressed to: USA Belvoir Research, Development, and Engineering Center, ATTN: STRBE-TSE, Fort Belvoir, VA 22060-5606 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by (let ter. AMSC

7、NIA FSC 4310 DISTRIBUTION STATEMENT A. Approved for public- release; distribution is unlimited. THIS DOCUMENT CONTAINS PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SPECIFICATIONS FEDERAL BB-A- 1 O 34 MIL I TARY MIL-V-17 3 MIL-P-5 14 MIL-C-3

8、600 MIL-G-3859 MIL-G-10924 MIL-D-16791 MIL-L-17331 MIL-G-23827 MIL-0-46168 MIL-E-52649 MIL-C-52773A q3 H 9797706 0277603 3 d, STANDARDS FEDERAL FED-STD-H28 FED-STD-101 MIL I TARY MIL-STD-130 MIL-STD-209 MIL-STD-461 MIL-STD-767 - Air Compressed, for.Breathing Purposes. - Varnish, Moisture-and Fungus-

9、Resistant (for Treatment of Communications, Electronic, and Associated Equipment). Marking, Blank. Compressors Reciprocating, Power-Driven: Air and Gas (Except Oxygen and Refrigerant), Packaging of. Screw Type. - Plates, Identification, Instruction and - Compressors, Rotary, Power-Driven: and - Grea

10、se Guns, Hand Operated, Lever, Push and - Grease, Automotive and Artillery. - Detergent, General Purpose (Liquid Non-ionic). - Compressor Lubricant, Diving, Normal Tempera- - Grease, Aircraft and Instrument, Gear and - Coating, Aliphatic Polyurethane, Chemical - Engine, Cold Starting Aids, Ether Fue

11、l ture. Actuator Screw. Agent Resistant. Primer s. I - Screw Thread Standards for Federal Service. - Test Procedures for Packaging Materials. - Identification Marking of US Military - Slinging and Tiedown Provisions for Lifting - Electromagnetic Emission and Susceptibility Property. and Tying Down M

12、ilitary Equipment. Requirements for the Control of El-ectro- magnetic Interference. Equipment, Including Piping Systems. - Cleaning Requirements for Special Purpose O 1 F 1 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5. b * MIL-C-52773A Lt3 E#!

13、 777770b 0277602 3 MIL-STD-889 MIL-STD-1246 MIL-STD-1330 MIL-STD-1359 MIL-STD-1410 MIL-STD-1472 MIL-STD-1474 MIL-STD-1622 MS 35 844 MS39 254 MS49006 - Dissimilar Metals. - Product Cleanliness Levels and Contamination Control Program. - Cleaning and Testing of Oxygen and Nitrogen Gas Piping. - Cleani

14、ng Methods and Procedures for Breathing Oxygen Equipment. - Methods for Selection of Industrial Engines for End Item Application. - Human Engineering Design Criteria for Military Sys tems . - Noise Limits for Army Materiel. - Cleaning of Shipboard Compressed Air Systems. - Plug, Machine Thread, Magn

15、etic (Drain). - Cartridge, Engine-Starting (Engine Cold- - Plug, Pipe, Magnetic-Headless, Aluminum, Iron Starting Aid). or Steel. 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to th

16、e extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. NAVFAC DM-39 NAVSEA 0994-LP-001-9010 NAVMAT P-9290 NAVMEDCOMINST 6260.3 Naval Experimental Diving Unit (NEDU) NAVSEA INSTRUCTION 10560.2 - Hyperbaric Facilities Design Manual 3

17、9. - US Navy Diving Manual Volume I. - System Certification Procedures and Criteria Manual for Deep Submergence Systems. - Occupational Health Surveillance Manual. - Air and Oxygen Systems Cleaning Procedure for Organizational Level Preventative and Correc- tive Maintenance. - Diving Equipment Autho

18、rized for Navy Use. ENVIRONMENTAL PROTECTION AGENCY (EPA) 40 CFR, Part 85 - Control of Air Pollution From New Motor Vehicles and New Vehicle Engines. (Application for copies should be addressed to the Superintendent of Documents, US Government Printing Office, Washington, DC 20402.) FOREST SERVICE F

19、orest Service Standard 5100-1. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-(Application for copies should be addressed to the Forest Service, US Department of Agriculture, P.O. Box 2417, Washington, DC 20013.) (Copies of specifications, standar

20、ds, handbooks, drawings, publications, and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) 2.2 Other publications. The following document(s) form a part o

21、f this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DoDISS specified in the solicitation. issues of documents not listed in the DoDISS shall be the issue of the non-Government doc

22、uments which is current on the date of the solicitation. Unless otherwise specified, the AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME) Performance Test Code PTC-9 - Displacement Compressors, Vacuum Pumps and Blowers. AMSE Boiler and Pressure Vessel Code, Section IX, Welding and Brazing Qualificati

23、ons. (Application for copies should be addressed to the American Society of Mechanical Engineers, 345 East 47th Street, New York, NY 10017.) AMERICAN SOCIETY OF TESTING MATERIALS (ASTM) F 307 - Gas, Pressurized, Sampling, Gas Analysis, Standard Method for. (Application for copies should be addressed

24、 to the American Society of Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. AMERICAN WELDING SOCIETY, INC. (AWS) D1.l - Structural Welding Code Steel. (Application for copies should be addressed to the American Welding Society, Inc., 550 NW Lejune Road, P.O. Box 351040 Miami, FL 331

25、35.) SOCIETY OF AUTOMOTIVE ENGINEERS (CAE) 5534 - Lubrication Fittings (Application for copies should be addressed to Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.) SOUTH COAST AIR QUALITY MANAGEMENT DISTRICT (SCAQMD) Rule 442 - Usage of Solvents. 4 Provided by IHSNo

26、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-52773A q3 W 7799906 0277b04 7 m MIL-C-52973A(ME) (Application for copies should be addressed to the South Coast Air Quality Management District, 9150 E. Flair Drive, El Monte, CA 91731.) O STATE OF CALIFORNIA AIR

27、RESOURCES BOARD Health and Safety Code. (Application for copies should be addressed to California Air Resources Board, 1709 11th Street, Sacramento, CA 95814.) - (Non-Government standards and other publications are normally available from I services. the organizations which prepare or which distribu

28、te the documents. documents also may be available in or through libraries or other informational These 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein (except for associated detail specifications, specification sheets or MS s

29、tandards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Description. The compressor unit shall be portable, and shall consist of a recip

30、rocating compressor, driven by a diesel engine, and shal.1 produce not less than 20 cubic feet per minute (cfm) of free air at 5000 pounds per square inch gage (psig). The engine and compressor unit shall be shock mounted. The compressor unit shall be complete and self-contained, including a final a

31、ir filter and all other accessories. The compressor unit shall weigh not more than 1500 pounds dry and the dimensions shall not exceed 50 inches in height, 60 inches in length, and 48 inches in width. A water resistant tarpaulin shall be provided. Divingldiving support equipment shall meet all stand

32、ards of Command, Code OOC, Alexandria, VA 20362. 0 i manufacturing divingldiving support equipment as approved by Naval Sea Systems 3.2 First article. Unless otherwise specified (see 6.21, a sample shall be subjected to first article inspection (see 4.3 and 6.4). deviations of compressors from the a

33、pproved first article during production will be subject to the approval of the contracting officer. article will not relieve the contractor of his obligation to furnish compressors conforming to this specification. Any changes or Approval of the first 3.3 Material. Material shall be as specified her

34、ein. Materials not specified shall be selected by the contractor and shall be subject to all provisions of this specification. 3.3.1 Material deterioration prevention and control. The compressor shall be fabricated from compatible materials, inherently corrosion resistant or treated 5 Provided by IH

35、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-to provide protection against the various forms of corrosion and deterioration that may be encountered in any of the applicable operating and storage environ- ments to which the compressor may be exposed. 3.3.2 Dissi

36、milar metals. Dissimilar metals shall not be used in intimate contact with each other unless protected against galvanic corrosion. Dissimilar metals and methods of protection are defined and detailed in MIL-STD-889. 3.3.3 Identification of materials and finishes. The contractor shall identify the sp

37、ecific material, material finish or treatment for use with component and subcomponent, and shall make information available upon request to the contracting officer or designated representative. 3.3.4 Recovered materials. For the purpose of this requirement, recovered materials are those materials wh

38、ich have been collected from solid waste and reprocessed to become a source of raw materials, as distinguished from virgin raw materials. The components, pieces and parts incorporated in the compressor may be newly fabricated from recovered materials to the maximum extent practicable, provided the c

39、ompressor produced meets all other requirements of this specification. Used, rebuilt or remanufactured components, pieces and parts shall not be incorporated in the compressor. 3.4 Environmental conditions. 3.4.1 Operation. The compressor unit shall operate as specified herein at any ambient tempera

40、ture from minus 25 OF to plus 110 OF. 3.4.2 Precipitation. The compressor unit shall perform as specified herein in rain falling at a rate of three inches per hour. 3.5 Safety. All reciprocationg, rotating or moving parts of the compressor unit shall be guarded when such parts are exposed to contact

41、 by personnel or otherwise create a hazard. All hot surfaces of the compressor unit, including exhaust pipes and other lines which may be subject to high temperatures, exposed to contact by personnel or which create a fire hazard, shall be fully guarded or insulated. Exhaust from the engine shall be

42、 directed so that it does not endanger personnel, and so that the possibility of exhaust entering into the compressor unit inlet is minimized. Electrical equipment, wires, and connectors shall be effectively guarded or insulated to protect all persoris and objects from electrical shock hazard. Nonfu

43、nctional sharp edges, projecting points and excessive length of fastening devices shall be avoided. 3.5.2 Noise limits. The noise produced by the compressor shall conform with MIL-STD-1474 requirements, with the exception of MIL-STD-1474, 5.2, 5.3, and 5.4 when tested in accordance with 4.5.2.9. The

44、 provision of MIL-STD-1474, 4.3 and 4.4 shall be provided if and only if MIL-STD-1474, 5.1.1.2 procedures have been pursued and documented to the satisfaction of the procuring, activity and written permission to exceed the 85 dB(A) limit is obtained from the procuring activity. Hazard signs shall co

45、nform with MIL-STD-1474, 4.3, except the sign will state “HEARING PROTECTION REQUIRED WITHIN (specify) FEET.” The sign shall be readable at the distance indicated on the sign. 6 a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5 3.6 Reliability and

46、maintainability. 3.6.1 Reliability. The specified mean-time-between-failure (MTBF), shall be O hours when tested as specified in 4.5.2.14. 3.6.2 Maintainability. The compressor shall operate as specifeci herein without repair of maintenance other than the contractors recommended normal scheduled adj

47、ustments and servicing as established by a maintenance schedule prepared and submitted by the contractor prior to test. All major assemblies shall be accessible for servicing, repair, and replacement without the removal of adjustment or repair shall be equipped with quick-disconnect fasteners. All f

48、asteners shall be of corrosion-resistant material or shall be treated to be Maximum use shall be made of interchangeable hardware and fasteners. Means for complete draining of lubricants, fuel and condensate traps shall be provided in an accessible location and shall be accessible for draining to a

49、container without splashing on any component. All maintenance, assembly, or disassembly operations shall be accomplished with common tools and special tools furnished with the compressor. The maintenance ratio (MR) shall not exceed 0.05 (see 6.3.2). m other major assemblies. Covers and guards which must be removed for component st corrosion resistant. All screw threads shall be in accordance with FED-STD-H28. 3.7 Performance. The rated capacity of the compressor shall