ARMY MIL-C-50734-1973 CONTROL COMMANDERS LASER RANGING C-9134 ( ) VVG-1 11738811《C-9134() VVG-1激光测距指挥官系统的控制 11738811》.pdf

《ARMY MIL-C-50734-1973 CONTROL COMMANDERS LASER RANGING C-9134 ( ) VVG-1 11738811《C-9134() VVG-1激光测距指挥官系统的控制 11738811》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-50734-1973 CONTROL COMMANDERS LASER RANGING C-9134 ( ) VVG-1 11738811《C-9134() VVG-1激光测距指挥官系统的控制 11738811》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-50734 12 a 9999906 O L -= MIL- C - 5 07 34 (MU) 8 August 1973 MILI TAR Y SPECIFICATION CONTROL, COMMANDERS, LASER RANGING: C-9134( )/VVG-1: 11738811 This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1. 1 This specification covers one

2、type of electronic unit known as Cozerol, Commanders, Laser Ranging: C-9134( )/VVG-1: 1173881 1 (see 6. 1). 2. APPLICABLE DOCUMENTS 2. 1 The following documents, of the issue in effect on date of invi=tion for bids or request for proposal, form a part of this specification to :le extent specified he

3、rein. SPECIFIC A TIONS Military MIL-F- 13926 MIL-1-45607 MIL-S-45743 Fire Control Materiel: General Specification Governing the Manufacture and Inspection of Inspection Equipment; Acquisition, Maintenance, and Disposition of Soldering, Manual Type, High Reliability Electrical, Electronic, Instrument

4、, Communication, and Radar for Aerospace and Control Systems, Procedures for FSC - 1240 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-?r?IIL-C-50734(MU) 8 August 1973 MIL-S-46844 Solder Bath Soldering of Printed Wiring Assemblies, Automatic Machine

5、 Type STANDARDS Mi 1 ita rv t MIL -STD - 1 O 5 MIL - STD - 1 O 9 MIL -STD - 8 1 O DRA WINGS Sampling Procedures and Tables for Inspection by Attributes Quality Assurance Terms and Defini ti ons Envirionmental Test Methods U. S. A rmy, Frankford Arsenal F8565556 Pressure Tester FI0955915 Assembly, Be

6、aring FI 173881 1 PA CKA GING DA TA 11738811 Control, Commanders, Laser Ranging: C-9134( )/VVG-I SHEET Packaging of Control, Commanders, Laser Ranging: C-9134( )/VVG-I Copies of specifications, standards, drawings, and packaging data sheets required by suppliers in connection with specific procureme

7、nt functions should be obtained from the pro.curing activity or as directed by the contracting officer. ) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-50734 12 9999906 043b95b 7 W 6 MIL-G50734(MU) 8 August 1973 3. REQUIREMENTS 3.1 Fabricat

8、ion. The Laser Ranging Commanders Control C-9134( )/VVG-1. herein referred to as the unit, shall be manufactured . . in accordance with Drawing F11738811 and drawings pertaining thereto, 3.2 General specification. The unit shall meet the following requirements , where applicable, of MIL-F-13926: a.

9、Order of precedence b. Dimensions and tolerances c. Inorganic protective ,surface finish d. Electrical and electronic assemblies e. Part identification ad marking f, Workmanship. 3.2.1 Soldering. Soldering sha11 be in accordance with MIL- S-45743 or MIL-S-46844, except that bare copper wire exposure

10、 shall be permitted at clipped ends of component leads. 3.3 Performance. Unless otherwise specified, the unit shall meet the performance requirements of this specification at standard ambient temperatures between 60 degrees Fahrenheit (OF) and 90F. 3.3.1 Loads, power, and signals. The unit shall per

11、form as specified.herein when the loads, power, and signals of table I are applied as specified, 3. 3.1.4 LAST indicator. With the t5. O Vdc and t10 Vdc powers (items 2,-1 and 2.2) of table I applied between pins J1 -K and J1-L, and pins J1-H and J1-L, respectively, the AST indicator shall not Light

12、. 2. 3) of table I between pins J1- J and J1 -L, the LAST indicator shall light. Upon subsequent application of the +15 Vdc power (item 3.3.1.2 RANGE RETURN SELECTOR. With the RANGE RETURN SELECTOR pushbuttons depressed and released in turn, the voltages specified in table II shall appear at the des

13、ignated pins of J1. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-50734 32 = 9999906 0433757 O I- C MIL-G 507 34(MU) 8 August 1973 - Item 1, I. 1 1.2 1.3 - 2. 2.1 2 2 2.3 3. 3.1 3.2 TABLE I LOADS, POWER, AND SIGNALS C on dit i on I Loads Re

14、 si stor Re si stor NAND gate Power Sources t5 Vdc t10 Vdc t15 Vdc Signal sources Digital Type-A Digital Type- B Characteristics 180 ohms (a) l w v) ? k d A v) d w H w z w Y Io Y .* E 1 0044 -Ir ri004-i- -0- 4 44 P I- 30 I I I I - I I I I .-_ MIL-C-50734 12 777790b 04317bL 2 1 I- a I I I I -c I I I

15、3- I I I I =- I I I c- I I I l r- CC c4 I I l “e- l I I =- I I I .,I al: -fi c;u u =oi 44 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-50734 12 W 779990b 0431962 4 W (fdwtncr Only) MIL C-50734(MU) 8 August 1973 - I I I I _I I. Output It I

16、JI-U and J1-V +0.2 t 0.2 Vdc Input to J1.J (Rfrrner Only) u Figure 1. Turn-off Reset Time +15.0 - Output at J1-U tnd J1-V *io mrec .= T 300 mrec 9 Figure 2. Turn-on Reset Time 0.7 Vdc O 0.2 Vdc +4.2 f 1.0 Vdc +0.2 0.2 Vdc Provided by IHSNot for ResaleNo reproduction or networking permitted without l

17、icense from IHS-,-,-U MIL-C-50734 32 3999906 0433963 6 W hiIL-C-50734(MU) 8 August 1973 TABLE VI MALF INDICATOR DISABLE NOTES: . All J1 pins are referenced to J1-L (return) 2. Legend: 1 = logical one, type A 2 = logical zero, type A NC = no connection 3. 3.2 Environmental. 3.3.2.1 Storage temperatur

18、e. The unit shall meet the require- ments of 3.3.1 at ambient temperature after exposure to and thermal stabilization at -80“ F and t160“ F. 3.3.2.2 Operating temperatures. The unit shall meet the require- c ments of 3. 3.1 while exposed to and thermally stabilized at -40F and +125OF, subsequent to

19、which the requirements of 3.3.1 shall be met at ambient tempe rature. 3. 3.2. 3 Vibration. The unit shall show no physical failure and shall meet the requirements of 3.3.1 after being exposed to the following vib rat or y condi tio ns : a. Amplitude: 1 /64 inch, constant (1 /32 inch double amplitude

20、) b. Vibratory motion: Simple harmonic c. Sweep time: d. Vibration cycling: Three linear or logarithmic sweeps 5 to 55 to 5 Hertz in a 5- minute period applied to each of the three mutually perpendicular axes (see figure 3). 3.3.2.4 Shock. The unit shall meet the requirements of 3. 3, 1 after being

21、exposed to a total of 18 shock impulses, three in each direction along the three mutually perpendicular axes defined on figure 3. Each shock impulse shall be a half-sine wave, with a time duration of 3. 5 IO, 5 milliseconds and a peak amplitude of 1OOg. Provided by IHSNot for ResaleNo reproduction o

22、r networking permitted without license from IHS-,-,-MIL-C-50734 12 W 7797706 0433964 H MIL- C - 5 O 734(MU) 8 August 1973 I z O k U Q u E E O u al k 5 M tz 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-50734 32 M 3777706 0433765 T MIL- C-

23、50734(MU) 8 August 1973 3. 3. 3 Sealing. With the unit initially pressurized with nitrogen or air to 5 fl pounds per square inch gage (psig), the loss of pressure shall not exceed O. 055 psig in one-half hour, except for special sampling- environmental during which th loss of pressure shall not exce

24、ed O. 22 psig in 2 hours. 3. 3. 4 Internal pressure. Subsequent to meeting the sealing requirements, the unit shall be dry flushed with an internal atmosphere containing nitrogen or air having a dew point of at least -63. 5OF. After the unit is flushed, an internal pressure of 3. 5 +O. 5 psig shall

25、be established. 3. 3. 5 Interface. The unit shall be capable of interfacing with the Bearing A ssembly, F10955915. 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-50734 12 99779Ob O4319bb 1 W MIL-G 50734(MU) 8 August 1973 4. QUALITY ASSURANC

26、E PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified, the supplier may utilize his own or any other facilities su

27、itable for the performance of the inspection requirements specified herein, unless disapproved by the Government. Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to pres

28、cribed requirements. The 4.1.1 General provisions. The component and subassembly Definitions of inspection inspection requirements of MIL-F-13926 form a part of the quality assurance provisions of this specification. terms shall be as listed in MIL-STD-109. 4.2 First article (initial production) app

29、roval. The requirement for first article approval and the responsibility (Government or contractor) for first article testing shall be as specified in the contract. The sample for first article approval tests shall consist of three units. The sample shall be manufactured in the same manner, using th

30、e same materials, equipment, processes, and procedures as used in regular production. shall be obtained from the same source of supply as used in regular production. All parts and materials, including packaging and packing, 4.2.1 Government testing. When the Government is responsible for conducting

31、first article approval tests, the contractor, prior to submitting the sample to the Government, shall inspect the sample to insure. conformance t.0 all the requirements of this SPecification- A record of this inspection, including certificates of conformance for materials shall be submitted with the

32、 sample. 4.2.2 Contractor testing. When the contractor is responsible for conducting first article approval tests, the sample shall be inspected by the contractor for all the requirements of this specification, The aample and a record of this inspection, including certificates of .canformance for ma

33、terials, shall be submitted to the Government for approval. inspection. The Government reserveo the right to witness the contractors 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ MIL-C-50734 32 999790b 0433967 3 MIL-G- 50734(.MU) 8 August 1973

34、 4.3 Inspection provisions 4. 3.1 Submission of product, Unless otherwise specified herein, or by the contracting officer, inspection lot size, lot formation and presentation of lots shall be in accordance with inspection and sampling procedures herein and submission of product provisions of MIL-STD

35、-105. 4. 3.2 Examination and tests 4.3.2.1 Components and subassemblies. All components and sub- assemblies shall be inspected in accordance with the inspection provisions contained in the respective specifications and Supplementary Quality Assurance Provisions (SQAPt listed in the technical data pa

36、ckage (TDP). In the absence of SQAPs, the applicable .quality assurance provisions of MIL-F-13926 shall apply. 4. 3.2. 2 First article testing. First article testing shall be All examinations and tests shall be witnessed When manu- conducted in accordance with tables VI1 through IX, to determine com

37、pliance with 4.2. by the Government Quality Assurance Representative. facturing processes, materials, applied are subject to change, or an adverse change occurs in perform- ance capability of the unit, this shall be cause to cease those operations contributing to the change or failure until correcti

38、ons have been made by the contractor and approved by the Government. or inspection techniques previously 4. 3.2. 3 Function tests. The requirements and tests in table VI1 shall be inspected on a 100 percent basis. shall be conducted at the standard ambient temperature. All examinations and tests 4.4

39、 Special sampling. The selection of samples shall be in accordance with section 7 of MIL-STD-105. 4.4.1 General. One unit shall be selected at random by a Government representative as a control sample from each 50 produced, The control sample shall meet the requirements and tests in table VIII, 14 P

40、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-C-5073q 12 777770b 0431968 5 = z MIL- C - 50 734(MU) 8 August 1973 TABLE VI1 FUNCTIONAL TESTS RANGERETURN SELECTOR LASER MODE CONTROL switch Dimmer (DMR) Test (TSW) switch illumination RETURNS Read-

41、out selection RANGE (METERS) readout selection Re adout blanking Manual reset Turn- off reset Turn-on reset MALF indicator 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-50734 32 W 799970b 0433967 7 I 1 Classifi- cation MIL-C-50734 (MU) 8 A

42、ugust 1973 Control Tests Requirements Test Paragraph 301. 302. Fabrication General specification 3. 1 3.2 Applicable drawings - visual vi sua1 MIL-F- 13926 - 4. 4. 2 Environmental. Three units shall be selected at random by a Government representative as a control sample from each 50 pro- duced or f

43、rom each months production, whichever occurs first. The control samples shall meet the requirements and tests in table IX. 4.4.3 Acceptance and rejection. Rejected lots shall be screened for all defective characteristics. units and resubmittance of rejected lots shall be in accordance with the accep

44、tance and rejection criteria specified in MIL-STD-105. Removal or correction of defective 4.5 Inspection equipment. Except as otherwise provided for by the contract, the contractor shall supply and maintain inspection equip- ment in accordance with the applicable requirements of MIL-1-43607. The ins

45、pection equipment listed in table X shall be utilized in performing the tests specified herein. TABLE IX SPECIAL SAMPLING - ENVIRONMENTAL Classifi- cation 303. 304. 305. 306, 307, 308. 309. Control Tests Storage tempe rat Ure Ope rating tempe rature Vibration Shock Sealing (2 hours) Interrial pressu

46、re Int e rfa c e Requirements 3.3.2. 1 3.3.2.2 3. 3.2.3 3.3.2.4 3.3.3 3.3.4 3. 3. 5 Test Par ag r aph 4. 6. it. 1 4. 616. i c 4. 6. 16. 2 4.6.16.3 4.6.17 4.6.18 4.6.19 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-50734 32 W 7779706 043377

47、0 3 = MIL-C- 50734(MU), 8 August 1973 - item 1. 2. 3. 4. 5. 6. - - TABLE X INS PE C TION E QUIPME N T Nomenclature DC Power Supply DC Power Supply DC Power Supply Ohmmeter DC Voltmeter Signal Source Description _ t5. O *O. 2 Vdc Ripple: 25 mV p-p maximurn +lo. O IO. 2 Vdc Ripple: 25 mV p-p maximum t

48、15. O IO. 7 Vdc Ripple: 25 mV p-p maximum Range: O to 10 megohms Accuracy: f5 percent Range: O to 20 Vdc Accuracy: fl percent Capable of providing d-c levels of amplitude as specified in items 3.1 and 3.2, table I. . 4.5.1 Government-furnished Inspection equipment. Where the contract provides for Government furnished inspection equipment, supply and maintenance of inspection equipment shall be in accordance with the applicable requirements of MIL-1-45607. 4.5.2 Contractor-furnished inspection equipment 4. 5.2. 1 Government design. Unless otherwise specified in the contract, all insp