ARMY MIL-C-44380-1989 CLIMBERS' EQUIPMENT SET SPECIAL OPERATIONS FORCES MOUNTAINEERING EQUIPMENT (SOFME)《特种部队登山装备(SOFME)脚扣装备》.pdf

《ARMY MIL-C-44380-1989 CLIMBERS' EQUIPMENT SET SPECIAL OPERATIONS FORCES MOUNTAINEERING EQUIPMENT (SOFME)《特种部队登山装备(SOFME)脚扣装备》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-44380-1989 CLIMBERS' EQUIPMENT SET SPECIAL OPERATIONS FORCES MOUNTAINEERING EQUIPMENT (SOFME)《特种部队登山装备(SOFME)脚扣装备》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、. ,* MIL-C-44380 84 777770b 0404038 II -=- - $-o%- a7 I INCH-POUND MIL-C-44380 (GL) SUPERSEDING MIL-P-44336(GL) 27 April 1988 2 November 1989 MILITARY SPECIFICATION CLIMBERS EQUIPMENT SET, SPECIAL OPERATIONS FORCES MOUNTAINEERING EQUIPMENT (SOFME) This specification is approved for use by the Natick

2、 Research, Development, and Engineering Center, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope, This specification covers one complete Special Operations Forces Mountaineering Equipment (SOFME) Set, 2. APPLICABLE DOCU

3、MENTS e 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Departm

4、ent of Defense Index of Specificatians and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). I Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Rese

5、arch, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization ,Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8465 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unli

6、mited. THIS DOCUMENT CONTAINS 8 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ -p_._s_ _ _- MIL-C-443BO Clothing, Personal.Equipment and Equipage; General Specification For MIL-W-5625 - Webbing, Textile, Nylon, Tubular STANDARDS MILITARY MI

7、L-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets Attributes. (Unless otherwise indicated, copies of federal and military specifications, sta

8、ndards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-C-44380 BLJ = 9979906 04OLJO40 T = 2.2 Other pub

9、lications. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. issues of documents not listed in the DOD

10、ISS shall be the issues of the nongovernment documents which are current on the date of the solicitation. Unless otherwise specified, the AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Com,ercial Packaging (Application for copies should be addressed to the American

11、Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other inf

12、ormational services.) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a spe

13、cific exemption has been obtained. 3. REQUIREMENTS 3.1 Material. One complete climbers equipment set shall consist of the materials and quantities specified in table I. It is encouraged that recycled material be used when practical as long as it meets the requirements of this specification. e TABLE

14、I. Container contents Container Quant i ty Box 1 12 each 6 each 6 each 6 each 6 each 6 each 6 each Item description Harness, climbing Stopper, wired, wedge, Stopper, wired, wedge, Stopper, wired, wedge, Stopper, wired, wedge, Stopper, wired, wedge, Stopper, wired, wedge, size I size II size III size

15、 IV size V size VI Specification A-A-50120 A-A-5 O 106 A-A-5 O 106 A-A-50 106 A-A-50 106 A-A-5 O 106 A-A-50 106 3 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44380(GL) TABLE I. Container contents (contd) Container Quant i t y Box 1 6 each

16、 continued 6 each 2 each Box 2 Box 3 Box 4 12 each 6 each 6 each 6 each 8 each 12 each 6 each 6 each 6 each 4 each 8 each 8 each 12 each 12 pair 14 pair 12 pair 1 roll 1 roll 1 roll 12 each 60 each Item description Stopper, wired, wedge, Stopper, wired, wedge, Rope, nylon, climbing type, size VI1 si

17、ze VI11 150 foot length Axe, ice Piton, mountain, fiat, Piton, mountain, flat, Piton, mountain, flat, Piton, mountain, flat, Piton, mountain, knife, Piton, mountain, angle, Piton, mountain, angle, Piton, mountain, angle, Piton, mountain, Piton, ice, type I Piton, ice, type II type 1 type II type III

18、 type IV blade, offset type 1 type II type III cliffhanger Hammer, rock and ice Crampons, hinged Straps, crampon Protectors, crampon Rope, kernmantle, type I, Rope, kernmantle, type II, Rope, kernmantle, type III, Snap link, mountain, Snap link, mountain, 150 feet long 150 feet long 150 feet long pi

19、ton, type II piton, type III Specification A-A-5 0 106 A-A-50106 MIL-R-1688 A-A-501 16 A-A-501 11 A-A-501 11 A-A-501 11 A-A-501 11 A-A-501 14 A-A-50112 A-A-50112 A-A-501 12 A-A-50115 A-A-50 113 A-A-50113 A-A-5 0096 A-A-50 117 A-A-501 18 A-A-50121 A-A-50 139 A-A-50139 A-A-5 0 1 39 A-A-5004 1 A-A-5004

20、 1 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-443O 4 7779706 O404042 3 = _ TABLE I. Container contents (contd) Container Quant i ty Box 4 6 each continued 6 each Box 5 4 each 8 each 1 roll Box 6 1 roll 2 each 2 each 4 each 8 pair 12 pai

21、r Item description Stopper, hexagon, Stopper, hexagon, irregular, size I irregular, size IIB Rope, kernmantle, type IV, Pulley, mountain rescue, Webbing, textile, nylon, tubular, 9/16 inch wide by 75 feet, long, color OD-7 Webbing, textile, nylon, tubular, 1 inch wide by 75 feet, long, color 00-7 An

22、chor, snow, wired, size 1 Anchor, snow, wired, size 2 165 feet long Rope, kernmantle, type IV, Ascenders, cam action Descender, figure-8 165 feet lorig Spec if icat ion A-A-5 0098 A-A-5 0098 A-A-5 O 139 A-A-50997 MIL-W-5625 MIL-W-5625 A-A-5 O 1 19 A-A-50119 A-A-50139 A-A-50 127 A-A-5 O 1 25 4. QUALI

23、TY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. otherwise specified in the contract or purchase orde

24、r, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements Specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are

25、 deemed necessary to ensure supplies and services conform to prescribed requirements. Except as 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection sys

26、tem or quality program. absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part o

27、f manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. The 5 Provided by IHSNot for ResaleNo r

28、eproduction or networking permitted without license from IHS-,-,-4.2 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.2.1 Component and material inspection. In accordance with 4.1, components and materials shall

29、be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document. 4.2.2 Packaging examination. The fully packaged end items shall be examined for the defects listed below. The

30、 lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The inspection level shall be S-2 (see 6.3). Examine Defect Marking (exterior Omitted; incorrect; illegible; of improper size, and interior) location, sequence, or method of

31、application Materials Any component missing, damaged, or not as specified Workmanship Inadequate application of components, such as: incomplete sealing or closure of flap, improper taping, loose strapping or inadequate stapling Bulged or distorted container Content Number per container is more or le

32、ss than required 4,2.3 Palletization examination. The fully packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one pelletized unit load, fully packaged. The inspection level sha

33、ll be S-1 (see 63). Examine Defect Finished dimensions Length, width, or height exceeds specified maximum requirement Palletization Pallet pattern not as specified Interlocking of loads not as specified Load not bonded as specified Weight Exceeds maximum load limits Mark i ng Omitted; incorrect; ill

34、egible; of improper size, location, sequence, or method of application 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-44380( GL) 5. PACKAGING 5.1 Preservation, Items shall be preserved as specified in the item documents 5.2 Packing. Packing

35、shall be level A, By or Commercial, as specified (see 6.2). 5.2.1 Level A packing. Items preserved as specified in 5.1 shall be packed in the quantities specified in table I in a fiberboard box conforming to style RSC-L, grade V2s of PPP-B-636. box liner conforming to type CF, class weather-resistan

36、t, variety DW, grade V15c of PPP-B-636, Voids in the shipping container shall be filled with crumpled kraft paper conforming to A-A-203. method IIf, waterproofed in accordance with method V, and reinforced as specified in the appendix of PPP-B-636. in unit loads in accordance with MIL-L-35078 for th

37、e type and class of load specified (see 6.2). except for type II, class F loads. The inside of each box shall be fitted with a Each box shall be closed in accordance with Shipping containers shall be arranged Strapping shall be limited to nonmetallic strapping, 5,2.2 Level B packing, Items preserved

38、 as specified in 5.1 shall be packed in the quantities specified in table I in a fiberboard shipping container conforming to style RSC-L, type CF (variety SW) or SF, grade 275 of PPP-B-636. The inside of each shipping container shall be fitted with a box liner conforming to type CF, variety DW, grad

39、e 200 of PPP-B-636. Voids in the shipping container shall be filled with crumpled kraft paper conforming to A-A- 203 * 5.2.2.1 Weather-resistant fiberboard containers. When specified (see 6.2) , the shipping container shall be a grade VC, VS, or V4s fiberboard box fabricated in accordance with PPP-B

40、-636, and closed in accordance with method III, as specified in the appendix of PPP-B-636. 5.2.3 Commercial packing. Items preserved as specified in 3.2 shall be packed in accordance with ASTM 0-3951. 5.3 Palletization. When specified (see 6.2), items packed as specified in Pallet type shall be type

41、 I (4-way entry), type 5.2. load type Ia of MIL-STD-147. IV, or type V in accordance with MIL-STD-147. Pallets shall be fabricated from wood groups I, II, III, or IV of MIL-STD-731. Each prepared load shall be bonded with primary and secondary straps in accordance with bonding means C and D, or film

42、 bonding means F or G. 2 or 5.2.3, shall be palletized on a 4-way entry pallet in accordance with 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5.4 Marking. In addition to any specia purchase order, shipping containers and pa acccrdance with MIL-

43、STD-129 or ASTM D-3951 6. NOTES marking required by the contract or letized unit loads shall be marked in as applicable. (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. The climbers equipment set is intended to provi

44、de climbing aids for rock, snow, and ice terrain for up to 12 personnel of the Special Operations Forces. 6.2 Acquisition requirements. Acquisition documents must specify the f o 1 lowing : a, Title, number, and date of this specification. b, Issue of DODISS to be cited in the solicitation, and if r

45、equired, the ca Levels of preservation and packing (see 5.1 and 5.2). d. Type and class of unit load (see 5.2.1). e, When weather-resistant grade fiberboard shipping containers are required f, When palletization is required (see 5.3). g. Acceptance criteria required (see 6.3). specific issue of indi

46、vidual documents referenced (see 2.1.1 and 2.2). for level B packing (see 5.2.2.1). 6.3 Acceptance criteria. The acceptance criteria below are recommended for use. The acceptance criteria as specified in the contract or purchase order shall be binding. Unless otherwise specified, the following accep

47、tance criteria are in accordance with MIL-STD-105. 6.3.1 For packaging examination. An AQL, expressed in terms of defects per hundred units, of 2.5 is recommended. 6,3,2 For palletization examination. An AQL, expressed in terms of defects per hundred units, of 6.5 is recommended. 6.4 Subject term (key word) listing. Piton Rock climbing Rope Custodian: Army - GL Preparing activity: Army - GL (Project 8465-AO49) a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-