ARMY MIL-C-44347-1988 CARRIER WATER CANTEEN COLD WEATHER CRS《耐蚀钢冬季水箱支架》.pdf

《ARMY MIL-C-44347-1988 CARRIER WATER CANTEEN COLD WEATHER CRS《耐蚀钢冬季水箱支架》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-44347-1988 CARRIER WATER CANTEEN COLD WEATHER CRS《耐蚀钢冬季水箱支架》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-44347(GL) i7 November 1988 MILITARY SPECIFICATION CARRIER, WATER CANTEEN, COLD WEATHER, CRS This specification is approved for use by the U.S. Army Natick Research, Development, and Engineering Center, Department of the Army, and is available for use by all Departments and Agencies of the Depa

2、rtment of Defense. 1. SCOPE 1.1 Scope. This document covers one type and size of canteen and cup carrier fabricated from nylon duck, nylon taffeta cloth and an insulation batting core, nylon tape and webbing, hook and pile fastener tape, plastic stiffeners, poly- ester thread, snap fasteners, and sl

3、iding keepers. 2. APPLICABLE DOCUMENTS 2.1 Government documents. MIL-C-LILl347 ALI 7777906 OLIO3536 b - - 2.1.1 Specifications, standards, and handbooks. !he following specifi- cations, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specif

4、ied, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the soli citation. SPECIFICATIONS FE DE RAL A-A-203 - Paper, Kraft, Untreated DDD-L -20 - Label: For Clothing, Equipage,

5、and Tentage, PPP-B-636 - Boxes, Shipping, Fiberboard (General Use Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U. S. Army Natick Research, Development, and Engineering Center, Natick, MA 0176

6、0-5014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. 1 FSC 8465 THIS DOCUMENT CONTAINS )q PAGES. ” AMSC N/A - DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by I

7、nformation Handling ServicesMIL-C-44347 4 m 9779906 0403537 8 m i, MIL IT AR Y MIL-L-35078 - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For STANDARDS MIL ITA R Y MIL-STD-IO5 - Sampling Procedures and Tables for Inspe

8、ction MILSTD-129 MILATD-147 - Palletized Unit Loads MILSTD-731 - Quality of Wood Members for Containers and Pallets by Attributes - Marking for Shipment and Storage (Copies of specifications , standards , and handbooks required by contractors in connection with specific acquisition functions should

9、be obtained from the *contracting activity or as directed by the contracting activity .) 2.1.2 Other Government documents, drawings, and publications. The following ot,her Government documents, drawings , and publications form a part of this speci.fication to the extent specified herein. issues shal

10、l be those in effect on the date of the solicitation. Unless otherwise specified , the DRAWINGS U. S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGNEERING CENTER 2-2479 - Carrier, Water Canteen, Cold Weather CRS (Copies of drawings, publications, and other Government documents required by contractors i

11、n connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other publications, The following documents form a part of this speci- fication to the extent specified herein. issues of the documents which are DOD ado

12、pted shall be those listed in the issue of the DODISS specified in the solicitation. fied, the issues of documents not listed in the DODISS shall be the issues of the nongovernment documents which are current on the date of the solicitation. Unless otherwise specified , the Unless otherwise speci- 2

13、 Licensed by Information Handling ServicesMIL-C-49347 81 777970b 0903518 T M MIL-C-44347( GL) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Copies should be obtained from American Society for Testing and Materials, 1916 Race Street, Philadelph

14、ia, PA 19103-1187.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services. 1 2.3 Order of precedence. In the event of

15、 a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. and regulations unless a specific exemption has been obtained. Nothing in this document , however , shall supersede applicable laws 3. WQUIREMENTS 3.1 Guide samples. Guide

16、samples, when furnished , are solely for guidance and information (see 6.3). Variations from the document may appear in the sample, in which case the document shall govern. 3.2 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (s

17、ee 4.3, 6.2, and 6.4). 3.3 Materials. The materials shall be as specified on drawing 2-2-479 and all subsidiary drawings and parts lists pertaining thereto (see 6.5). 3.4 Design and construction. The design and construction of the carrier shall be as specified herein and as shown on Drawing 2-2-479

18、and all subsidiary drawings and parts lists (PLS) pertaining thereto. 3.4.1 Stitches, seams and stitching. All seams and stitchings shall be as specified on the drawings. 3.4.1.1 Automatic stitching. Automatic machines may be used to perform any of the stitch patterns provided the requirements for t

19、he stitch pattern, stitches per inch, and size and type of thread are met; and at least three tying, overlapping or backstitches are used to secure the ends of the stitching. 3.4.1.2 Lubrication of thread. There shall be no lubrication of the thread prior to or during sewing (see 4.4.1.1). 3.4.1.3 T

20、ype 301 stitching. Ends of all stitching shall be backstitched or overstitched a: specified on the drawings except where ends are turned under or caught in other seams or stitching. Thread tensions shall be maintained so that there will be no loose stitching resulting in loose bobbin or top thread o

21、r excessively tight stitching resulting in puckering of the materials sewn. lock shall be imbedded in the materials sewed, The 3 i. - Licensed by Information Handling ServicesMIL -C-4 4 347 ( GL ) 3.4.1.3.1 Repairs of type 301 stitching. Repairs of type 301 stitching shall be as follows: a. When thr

22、ead breaks or bobbin run-outs occur during stitching, the stitching shall be repaired by restarting the stitching a minimum of 1 inch (1/2 inch for box stitching) back of the end of the stitching. b. Thread breaks or two or more consecutive skipped or runoff stitches noted during inspection of the i

23、tem (in-process or end item) shall be repaired by overstitching. The stitching shall start a minimum of 1 inch in back of the defective area (1/2 inch on box stitching), continue over the defective area, and continue a minimum of 1 inch (1/2 inch on box stitching) beyond the defective area onto the

24、existing stitching. ing shall be repaired by removing the defective stitching without damaging the materials and restitching in the required manner. Loose or excessively tight stitch- (When making the above repairs in a. and b. above, the ends of the stitching are not required to be backstitched.) 3

25、.4.1.4 th at the re 3.4.1.3.la appears. 3,4.1.5 length. Types 503 or 504 stitching. Thread tension shall be maintained so will be no loose stitching, All repairs shall be in accordance with and 3.4.1.3.1b, except substitute 3/4 inch for 1 inch wherever 1 inch Thread ends. All thread ends shall be tr

26、immed to 1/11 inch maximum 3.4.2 Setting of snap fasteners, A hole shall be prepunched through the materials to receive the button and eyelet components of the snap fasteners, The hole shall be smaller than the outside diameter of the button and eyelet barrels so that the barrel must be forced throu

27、gh the hole. The hole shall not be punched in the setting operation with the button or eyelet barrel. The fasteners shall be securely clinched without cutting the surrounding materials and no more than three splits shall occur in the button or eyelet barrels. 3.4.3 Location marks. Location marks sha

28、ll not be drilled. Printed markings shall not be more than 1/32-inch in width. 3.5 Repairs. Repairs such as mends, darns, patches, or splices are not permitted on the canteen carriers. 3.6 Replacement of defective components. During the spreading, cutting and manufacturing process, components having

29、 material defects or damages that are classified as defects in 4.4.3, shall be removed from production and replaced with non-defective and properly matched components. 4 Licensed by Information Handling Services. MIL-C-qq347 4 7977706 0403520 = - MIL-C-44347(GL) 3.7 Marking. The identification marki

30、ng shall be applied in the location shown on Drawing 2-2-481 and shall conform to type IV, class 5 of DDD-L-20. The letters iiUSil shall be applied in the size characters and in the location indicated on Drawing 2-2-480 and shall conform to type IV, class 9 of DDD-L-20. Fastness of the class 9 marki

31、ng shall be as specified for class 5 marking. 3.7.1 Instruction label. An instruction label of the size and requirements specified on PL 2-2-483 shall be sewn on the inside of the flap as indicated on Drawing 2-2-490. The characters used in printing the label shall be of maximum size commensurate wi

32、th the area and contents specified. The legend shall be located on the label so that no part of the legend will be obscured by stitching or binding when sewn in the cover. 3.7.1.1 Legend. The contents of the instruction label shall be as follows: FILLING AND THAWING OF THE CANTEEN Fill the canteen t

33、o the Fill Mark stamped on the canteen. Do not fill canteen over the fill mark as overfilling will damage the canteen. Remove all Plastic Parts before thawing the canteen over an open fire. HAND WAS HIN G Wash the carrier, the canteen and the cup in a pail of warm water using mild detergent or soap.

34、 Do not use Chlorine Bleach, Yellow Soap, Cleaning Fluids or Solvents as these cleaners will discolor/deteriorate the items. Rinse thoroughly in clean warm water. Dry the items in shade or indoors. Do not dry in direct sunlight, direct heat or open flame. 3.8 Workmanship. The carrier shall conform t

35、o the quality of product established by this document and occurrence of defects shall not exceed the applicable acceptable quality levels. 4. QUALITY ASSURANCE PROVISIONS I 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible

36、for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unles

37、s disapproved by the Government. The Government reserves the right to perform any of the inspectioris set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 5 Licensed by Information Handling Services. MIL-C-443

38、47 (GL) 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification s

39、hall not relieve the contractor of the responsibility of ensuring that all products or supplles submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to req

40、uirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.1.2 Responsibility for dimensional requirements. Unless otherwise speci- fied in the contract or purchase order, the contr

41、actor is responsible for ensuring that all specified dimensions have been met. When dimensions cannot be examined on the end item, inspection shall be made at any point, or at all points in the manufacturing process necessary to assure compliance with all dimensional requirements. 4.1.3 Certificates

42、 of compliance. When certificates of compliance are sub- mitted, the Government reserves the right to inspect such items to determine the validity of the certification. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspect

43、ion (see 4.3). b. Quality conformance inspection (see 4.4). 4.3 First article inspection. When a first article is required (see 6.2), it The presence of shall be examined for the defects specified in 4.4.3 and 4.4.4. any defect shall be cause for rejection of the first article. 4.4 Quality conforman

44、ce inspection. Unless otherwise specified, sampling for inspect ion shall be performed in accordance with MILSTD- 105. 4.4.1 Component and material inspection. In accordance with 4.1, components and materials shall be inspected in accordance with all the requirements of referenced specifications unl

45、ess otherwise excluded, amended, modified or qualified in this specification or applicable purchase specification. 4.4.1 .I Certification. The contractor shall furnish a certificate of compliance for the requirement of 3.4.1.2 prohibiting use of thread lubricants prior to or during sewing. 4.4-2 In-

46、process inspection. Inspection shall be made at any point or during any phase of the manufacturing process to determine whether cut lengths, cut parts, fabricated parts before assembly, and marking for location of components are in accordance with specified requirements for dimensions and that opera

47、tions 6 %. I - . -. . Licensed by Information Handling ServicesMIL-C-44347(GL) and assemblies are accomplished as specified. made during the manufacturing process to ensure that holes for receiving hardware are prepunched smaller than the outside diameter of the tube. When- ever nonconformance is no

48、ted, corrections shall be made to the items and lot in- process. In addition, inspection shall be Items which cannot be corrected shall be removed from production. 4.4.3 End item visual examination. The end items shall be examined for the defects listed in table I. The lot size shall be expressed in

49、 units of carriers. The sample unit shall be one completely fabricated carrier. The inspection level shall be II and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 2.5 for major and 6.5 for total (major and minor combined) defects. TABLE I. End item visual defects Classification Exami ne Defect Major Minor - Cloth, duck, nylon Any hole, cut or tear, smash, broken or missing yarns, or open place clearly visible at normal inspection distance (approximately 3 feet) Fastener tape-hook Any hole, cut or tear and pile Hooks mi