ARMY MIL-C-40153 L (1)-1994 CLOTHING REPAIR SHOP TRAILER MOUNTED《装在拖车上的服装修理厂》.pdf

《ARMY MIL-C-40153 L (1)-1994 CLOTHING REPAIR SHOP TRAILER MOUNTED《装在拖车上的服装修理厂》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-40153 L (1)-1994 CLOTHING REPAIR SHOP TRAILER MOUNTED《装在拖车上的服装修理厂》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-40L53L (1) 999990b I1979590 897 MIL-C-40 153L -1 31 March 1994 MILITARY SPECIFICATION CMHING REPAIR SiiP, TRAILER KUNIP) This amerxhnt fonrrs a part of ML-C-40153L, ciate 30 Senber 1991, and is approved for use by all Departments ami Agencies of the Department of Defense. PAa3 2 2.1.1, wier “S

2、PECIFICATICNS, FEDEBAL“: Delete “A-A-50470“, “RR-I-660“, and ffPPP-C-843“ arid their titles. under “SPECIFICATICBJS, FEDERAL“: Add the following: “ A-A-297 - Ironing Board, Household A-A-1805 - Cover, Ironing Board A-A-1806 - Pad, Ironing Board A-A-1898 - Cushioning Material, Cellulosic, Packaging A

3、-A-50473 - Oil-, Harid, Push-Witta PPP-B-26 - Bag, Plastic (General Purpose) PPP-F-320 - Fiberboard: corrugated and Solid, Sheet Stock (Container Grade), and Cut Shapes“ under “SPECIFICATIOEJS, MILITARY“: Delete “MIL-B-117“ and its title. Add the following: “ML-T-10579 - Trailers, Cargo: 2 Wheel, 1/

4、4 Ton to 1-1/2 Ibn PAGE 9 3.4.6: Delete and suhtitute: “3.4.6 Imninu board, pad, and cover. The ironing board shall conform to nie pad shall conform to The cover shall A-A-297, except the top dimensions shall be 27 _+ 1/4 by 7 2 1/4 inches werall, and the stand shall not be adjustable and shall be s

5、uitable for mounting on a folding table, per Drawing 6-1-1117. A-A-1806 ami be suitable for mounting on the ironing boami. conform to class B of A-A-1805 and be suitable for covering the ironing board with the pad mounted.“ AMSC N/A 1 of 4 FSC 3530 DISl!fUEW.IN S?A!EMEXC A. Approved for public relea

6、se; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-40153L -1 3.4.9, TABLE III: Item 1: After “1/4-inch“, Add: “or V-belt, rubber, 3L“ Itgn 3: Delete “Description“ and substitute: “Oiler, hand, push bottan, steel, 4-i

7、nch straight spout, polished copy clear lacquer or vamish, 1/2 pint, class A per A-A-50473“ Item 8: Delete “Description“ and substitute: “Screwdriver, Flat Tip, Plastic Handle, 9/64 by 2-inch blade, type I, class 8, style 1 or 2 of a3G-S-12111 Item 11 and Item 12: Delete “brass, chmne plated, closed

8、,“ and substitute “solid nicke silver, closed, I PWE 13 4.4.1.1: Delete and substitute: “4.4.1.1 Canponent testinq. The electrical and mechanical caqmnents of vpon successful canpliance, each prociuCt end item shall be tested for proper operation. test is a test of the equiprient and electric distri

9、bution system. done independently of the cabinet fabrication. each equipent group and electrical distribution system shall be tagged inspected, and may be preservation pckaged. shall be cause for rejection of the equiprrent and distribution system.“ The operational It may be Failure to pass these te

10、sts Add the following new paragraphs: 4.4.1.1.1 Pmr and distribution box assemblies. Each conductor of the power box 2LIIcI distribution box assemblies shall be checked for proper continuity. In addition each conductor in the cable will be checked for insulation resistance from that conductor to eve

11、ry other conductor. The insulation resistance shall not be less than 1 mega ohm when tested at a voltage of not less than 500 volts direct current (VDC). 4.4.1.1.2 Electrical extension liuht. Each light shall be checked for 4.4.1.1.3 Clothinu sewinu machine assembly. Each clothing sewing mchine oper

12、ation by plugging in the light to a standard 110 volt (V) socket. shall be subjected to the examination and test paragraphs as specified in -S-256/GEN. machine of CQ-S-256/1 shall be verified. Conforniance to the requirements of stitch type 301, class 3 2 Provided by IHSNot for ResaleNo reproduction

13、 or networking permitted without license from IHS-,-,-MIL-C-40153L l#MmmmTl 4.4.1.1.4 Darnina sewinu machine assembly. Each darning sewing machine shall be subjected to the examination and test paragraphs as specified in OO-S-256/GEN. OO-S-256/3 shall be verified. Conformance to the requirements of

14、class 3 machine of 4.4.1.1.5 Button sewinu machine assemblies. Each button sewing machine shall be subjected to the examination and test paragraphs as specified in -S-256/GEN, except that the operational test shall be as described in the “test“ paragraph of -S-256/8. Conformance to the requirenents

15、of class 1 button machine shall be verified.“ PAGE 14 4.4.5, last sentence: Delete and substitute: “The inspection level shall be S-2. The finding of any defezt shall be cause for the rejection of the lot.“ PAGE 15 4.5.3, e.: Delete and substitute: “e. The generator shall be started and adjusted for

16、 120/208 volts, 60 cycles, 3 phase electrical output.“ 1.: Delete and substitute: “1. Using the data recorded above, the electrical load on each phase shall be in canpliance witht the requirement in 3.5.3. PAGE 16 5.1.1.2, lines 8 and 9: Delete “type I, class B of PPP-C-843“ and substitute “grade II

17、, class B of A-A-1898, or type CF, class danestic, variety SW, grade 175 of FPP-F-320“. Line 10: Delete “cord or twine“ and substitute “cord, twine or tape*, . Line 13: Delete “type I, class E of MIL-B-117“ and substitute “style 1 or 3 of PPP-B-26“. 5.1.1.3, line 7: Delete “IA-14 of MIL-P-116“ and s

18、ubstitute “IA-15 of MIL-P- 116“ . 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-40153L umNUmnl MILITARY I“R: custodians: Army-a Air Force - 99 Review activities: Army-m Air Force - 84 m-GS User activity: Preparing activity: Anrsr-a (Project 3530-0097) Navy - IC 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-