ARMY MIL-B-63524 A-1988 BATTERY HED SINGLE CELL PRIMARY RESERVE《储存单电池压力继电器电池》.pdf

《ARMY MIL-B-63524 A-1988 BATTERY HED SINGLE CELL PRIMARY RESERVE《储存单电池压力继电器电池》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-B-63524 A-1988 BATTERY HED SINGLE CELL PRIMARY RESERVE《储存单电池压力继电器电池》.pdf（37页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-B-63524A (AR) i2 JANUARY 1988 SUPERSEDING MI L-B-63 52 4 (AR) 23 August 1982 MILITARY SPECIFICATION BATTERY, HED, SINGLE CELL, PRIMARY RESERVE This specification is approved for use within the U.S. Army Armament Munitions and Chemical Command, and is available for use by all Departments and Agen

2、cies of the Department of Defense, 3 1. SCOPE i* - 1.1 Scope. This specification contains requirements not normally covered by the drawings and provides quality assurance provisions for the fabrication of parts, assembly, and packing of the HED, single cell, primary reserve battery. 2. APPLICABLE DO

3、CUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards

4、(DODISS) and supplement thereto, cited in the solicitat ion. e specification to the extent specified herein. Unless otherwise SPECIFICATIONS MI LI TARY MIL-A-48 07 8 - Ammunit ion, Standard Quality As su rance MIL-P-63238 - Projectile, 155MM, AT; M718/M741 Loading, Assembling and Packing of MI L- T-

5、63 42 O Thionyl Chloride Electolyte MIL-P-63430 - Projectile, 155MM, Test, Non-Haz, M718/M741 Types Loading, Assembling and Packing of MIL-B-63524A 13 7777706 0351760 -di47 Beneficial comments (recommendations. additions. deletions) and any perthent date which may be of use in Improving this documen

6、t should be addressed to: Commander, U.S. Army Armament,Munitions and Chemical Command, Ath. AMSMC-QA. Picatinny Arienal. New Jersey 07806-5000 by using the self-addressed Standardiza- tion Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by. letter. AMSC NIA FSC

7、 1345 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 0 7 THIS DOCUMENT CONTAINS -37 PACES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-63524A 33 W 777770b 0353763 T m MIL-B-63524A(AR) STANDARDS MILITARY MI

8、L-STD-105 MIL- STD- 20 2 MIL-STD-331 MI E- STD-116 8 MIL-STD- 11 6 9 - Sampling Procedures an1 Tables for Inspect ion by Attributes - Test Methods for Electronic and Electrical Component Parts - Fuze and Fuze Components Environmental and Performance Tests for - Lot Numbering of Ammunit ion - Packagi

9、ng, Packing and Marking for Shipment of Inert Ammunition Components 2,1.2 Other Government documents, drawinqs, and publications. The following other Government documents, drawinqs, and Publicat ions form a part f this specification to the extent Specified herein. Unless otherwise specified, the iss

10、ues shall be those in effect on the date of the solicitation. DRAWINGS U. S. ARMY ARMAMENT RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER (ARDEC) PRODUCT AND PACKAGING DRAWINGS 9317598 - Projectile, 155MM Test, Non-Haz, M741 Type 9317608 - Mine, Test, Non-Haz (M741) 9328787 - Battery HED, Single Cell

11、, Primary Reserve INSPECTION EQUIPMENT DRAWINGS 9275628 - Firing Pin 9275634 - Procedure, Assembly, Power Source 9287150 . - M718 Electronics Assembly 9287151 - M741 Electronics Assembly 9275635 - Modified Molding, Power Source 9296892 - Primer, Stab (Copies of specifications, standards, handbooks,

12、drawings, publicat ions, and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted witho

13、ut license from IHS-,-,-MIL-B-6352LIA 13 m 7777706 03517b2 L m 2.2 Other publications. The following document forms a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DD adopted shall be those listed in the issue of the DDIS

14、S specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DDISS shall be the issue of the nongovernment documents which is current on the date of the solicitation. AMERICAN SOCIETY FOR TESTING AND MATERIALS ASTM E 493 - Standard Methods of Test for Leaks

15、Using the Mass Spectrometer Leak Detector in the Inside-Out Testing Mode. (Application for -copies of ASTM publication should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, Pennsylvania, 19103) . 2.3 Order of precedence. In the event of a conflict bet

16、ween the text of this specification and the references cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unles

17、s a specific exemption has been ob ta ined. 3 . REQUIREMFNTS 3.1 Materials. Materials and parts shall be in accordance with applicable drawings and specifications. 3.2 Components and assemblies. The components and assemblies shall comply with all requirements specified on drawing 9328787 and associa

18、ted drawings and with all requirements specified in applicable specifications and standards. 3.3 Non-activation voltage. The non-activation voltage of the battery, recorded at: Relative Humidity (RH) a. Max 40% shall be less than Millivolt 5mV b. Greater than 45% shall be at a max of 200mV All measu

19、rements are to be recorded with an approved millivoltmeter having a minimum impedance of lo7 ohm. 3.4 Battery voltaqe rise time. The battery voltage shall rise to minimum voltage of 2.5 volts in a maximum of one half (0.5) second after activation over the temperature range of -45OF to +145OF. Provid

20、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-63524A (AR) 3.5 Battery capacity. The battery shall remain above 2.5 volts for a minimum of two hundred and forty (240) hours when subjected to a 6.6K ohm - + 3% resistive load over the temperature rang

21、e of -45OF to +1450F. 3.6 Leak test. The batteries shall meet the leak rate requirements as specified on the drawing (9328787) when tested in accordance with the provisions of paragraph 4.4.6.5. 3.7 Weld inteqrity. 3.7.1 Anode lead to terminal pin weld. The anode lead to terminal pin weld, when pull

22、ed to destruction, shall not result in separation of the weld. Lead material shall fail before the weld. 3.7.2 Anode and cathode lead to screen welds. The anode .and cathode lead to screen weld, when pulled to destruction, shall not result in separation of the weld. Parent material (screen or lead)

23、shall fail before the weld. 3.7.3 Case to terminal plate weld. The case to terminal plate weld shall not show evidence of pits or cracks when visually examined . 3.8 Terminal plate qlass to metal seal. The glass seal shall. not have cracks on both sides of the pin or any one crack that extends over

24、one-third the distance from the pin to the plate. 3 . 9 Radioqraphic examinat ion. X-ray negatives of the batteries shall be examined for the following : a. There shall be continuity of the anode lead. b. There shall be no sharp bends in the anode lead. t c. The anode lead shall not be bent against

25、the outside case. d. The ampul shall be intact and show evidence of electrolyte. 3.10 Heat soak. The ampul assembly, electrolyte (9328782) shall withstand a 24 hour heat soak at 165 5 50F without leakage or breakage. 3.11 Environmental tests. The batteries shall meet the requirements of paragraphs 3

26、.3, 3.4, 3.5 before and after being subjected to the following tests: a. Shock. Drop per MIL-STD-331, Test 111, except batteries shall be mounted in hardwood block of 40 CU. inches weighted to 5 pounds and shall be dropped from the height of 7 ft. b. Transportation vibration. Per MIL-STD-331, Test 1

27、23. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-B-6352qA 13 m 7979706 0351764 5 3.12 Ballistic rail gun test. The batteries shall meet the requirements of paragraph 3.3 prior to and after being subjected to 10,000 + 800/-3OOgs when tested

28、in accordance with the provisions of paragraph 4.4.6.8. 3 . 13 Ballistic funct ioninq . The batteries shall function properly when assembled and tested in 155MM Test Non-Haz, M718/M741 Types at Zone 7 charge for the Ml09A1. 3.14 Ampul assembly electrolyte condition. The electrolyte when examined ins

29、ide the ampul shall be clear and of a colorless or light yellow to light pink appearance. e -e 3.15 Hardness of case. The case (9275592) shall have a Knoop hardness of 231 max at 200 gm load, or 96 Rockwell B (max.). 3.16 Surveillance. The contractor shall provide for surveillance quantities of batt

30、eries from each months production. A total quantity of 160 batteries per lot shall be supplied in accordance with 4.5.7. 3.17 First article inspection. This specification contains technical provisions for first article inspection. Requirements for the submission of fir st article samples by- the con

31、tractor shall be as specified in the contract. and finished in a thorough workmanlike manner, and all manufacturing, processing, and assembly operations shall be correctly performed. Metal parts shall be free of burrs, chips, sharp edges, cracks, crazes, unblended radii, porosity, warpage, burn mark

32、s, checks, chipped edges, blisters, excess flash, dirt, grease, rust, salt deposits, corrosion products, and other defects or foreign matter which would affect their serviceability. The cleaning method used shall not be injurious to any part or assembly, nor shall the parts be contaminated by the cl

33、eaning agent, All required markings shall be neat, legible and sharply defined. 3.18 Workmanship. All parts and assemblies shall be fabricated e 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsi

34、ble for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the

35、Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Unless otherwise specified herein or in the contract, the provisions of MIL-A

36、-48078 shall apply and are hereby made a part of this detail specification. 0 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-B-6352LIA 13 9999906 0353765 7 4.1.1 Responsibility for compliance. All items must meet all requirements of sections

37、3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplie

38、s submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. 4.2 Classification

39、of inspections. The inspection requirements specified herein are classified as follows.: a. First Article Inspection (see 4.3) b. Quality Conformance Inspection (see 4.4) 4.3 First article inspection. 4.3.1 Submission. The contractor. shall submit a first article sample as designated by the Contract

40、ing Officer for evaluation in accordance with the provisions of 4.3.2 and 4.3.3. The first article sample shall consist of the items in sample quantities as indicated. Part Description Draw ins s Quantity Battery, HED, Single Cell Primary Reserve 9328787 438 4.3.2 Inspections to be performed. See MI

41、L-A-48078, and paragraphs 4.4.2, testing per paragraph 4.4.3, and Table I specified here in . 4.3.3 Rejection. See MIL-A-48078. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flfL-B-6352qA 13 a 9999906 0351766 9 W CI 3 Y 4 * cv In m W I I d m E r

42、w w c .II r fi n 8 IL w Z O F: Li Li O 8 a E c O 4 U .rl tll O a u 5 C m rl 4 -4 Li al U 4 8 h rl a E al tll 2 5 Emvi al5 m al c tll ala Li al o me 4 E amo -4 m al an u a,oalalal x uynJ E 5 al c .rl 4-1 al 5 al c O 2; al 5 O c 4 41 rl e Provided by IHSNot for ResaleNo reproduction or networking perm

43、itted without license from IHS-,-,-c F r Y n Y d Y w Z O F: o !k - u, 3 u w O 03 rl NN rl m MM m o o. o dpdp dp mm m I ww w I e. . O0 o W a, c -4 w a, a al c O z ci c,u Li ua, a, Li a Li H w z h h rl a E al m 2 al m W u al 5 O WG u W u rl rlrl rl rl w mm m m 03 N CJN m rl 8 *e . m mm m m dp dpdp dp

44、dp o O0 o In * * * o O0 o O . .* 8 * 3r 5 rl aJ 5 al c .d w al 5 al c: O z al-ici - c u walo c arlaa-4 (u ow o ou 29 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-63524A 23 799990b 0352787 T rl 8 t rl i w O c O dPdPdp mmm w 0 w O00 . 1 I Q a, C -I4 u a, a a, c O z 30 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-