ARMY MIL-B-48600 A (3)-1991 BASE PLUG ASSEMBLY《底部插座组件》.pdf

《ARMY MIL-B-48600 A (3)-1991 BASE PLUG ASSEMBLY《底部插座组件》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-B-48600 A (3)-1991 BASE PLUG ASSEMBLY《底部插座组件》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-B-48600A (AR) AMENDMENT 3 15 June 1991 SUPERSEDING AMENDMENT 2 17 .October 1986 MILITARY SPECIFICATION BASE PLUG ASSEMBLY This amendment forms a part of Military Specification MIL-B-48600A (AR), dated 30 October 1979, and is approved for use by the U.S. Army Armament, Munitions and Chemical Comm

2、and and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1 Issues of documents. Under SPECIFICATIONS MILITARY, 11MIL-C-60539 - Coatings, Anodic, Conventional, for Aluminum and Aluminum Alloys.I1 - and substitute: delete: MI L -A - 8 6 2 5 - Anodic Coatings,

3、 for Aluminum and Aluminum A 1 1 oy s. Under STANDARDS MILITARY, add: 11MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes. MIL-STD-1167 - Ammunition Data Card.“ PAGE 5 Table I First article inspection. Under Notes, delete: t1MIL-A-6053911 and substitute 11MIL-A-862511. AMSC N

4、/A 1 of 3 FSC 1315 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_- _ - - MIL-B-48600A (3) 13 W 9999906 0483298 4 MIL-B-48600A (AR) AMENDMENT 3 PAGE 7 8 4.4.2.1 Major

5、 102 Sample size column: delete 1r5tr and substitute “See 4.5.1.It1. Major 106: Delete llwi th large outside diametert1. Add Major 111: tllll Runout of large outside diameter 0.40% 3.1 Gage“. PAGE 8 4.4.2b Tool control dimensions. Line 5, delete: llmesurementsll and substitute ltmeasurementsfl. PAGE

6、 IO 4.5.1.1 Delete this paragraph in its entirety and substitute: t14.5.1.1 Salt spray test-base plug. The salt spray test shall be accomplished in accordance with MIL-A-8625. Two samples for every 5000 units shall be selected during regular production (each lot) for the salt spray test. These sampl

7、es shall be exposed for 120 hours, beginning with the first lot produced and continuing until three consecutive lots have complied with the applicable requirements. After three consecutive lots have been accepted, the samples of all subsequent lots shall be exposed for 72 hours. Should any lot fail

8、the applicable requirements, the salt spray samples of the following lot shall be exposed for 120 hours until three consecutive lots have been accepted.I1 5.1.2 Level B - Mininum military package. Line 1, delete: itomplyll and substitute tlcornplyll. 2 Provided by IHSNot for ResaleNo reproduction or

9、 networking permitted without license from IHS-,-,- MIL-B-48bOOA (3) 13 9999906 0483299 b W 1 MIL-B-48600A (AR) AMENDMENT 3 PAGE 11 6.2b Delivery of data cards to the technical agency. Delete: “Commander, US Army Armament Research and Development Command, ATTN: DRDAR-QAR-E, Dover, NJ 078Olt1 and sub

10、stitute: Commander U.S. Army Armament, Research, Development and Engineering Center, Dover, NJ 07801-5001t. ATTN: AMSMC-QAT-A 6.3 Submission of inspection equipment designs for approval. Delete: Commander, US Army Armament Research and Development Command, ATTN: DRDAR-QAR-I, Dover, NJ 078Olt1 and su

11、bstitute: Commander U. S. Army Armament, Research, Development and Engineering Center, Dover, NJ 07801-5001tt. ATTN: AMSMC-QAT-I NOTE: The margins of this Amendment are marked with an asterisk or vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the pre

12、vious amendment were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Cu s t odi an: Army - AR Preparing activity: (Project 1315-AD09) Army - AR 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-