ARMY MIL-B-43826 C-1989 BELT INDIVIDUAL EQUIPMENT《单独设备带》.pdf

《ARMY MIL-B-43826 C-1989 BELT INDIVIDUAL EQUIPMENT《单独设备带》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-B-43826 C-1989 BELT INDIVIDUAL EQUIPMENT《单独设备带》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、e 5 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardization Document Imp

2、rovement Proposal (DD Form 1426) appearing at the end of this document or by letter. MIL -B-43 826 C 6 September 199 SUPERSEDING MIL -B -4 3826B 21 December 1982 MILITARY SPECIFICATION BELT, INDIVIDUAL EQUIPMENT This specification is approved for use by all Departments and Agencies of the Department

3、 of Defense. 1. SCOPE 1.1 Scope. This specification covers one type of adjustable individual equipment belt made from olive drab nylon webbing, plastic and miscellaneous metallic hardware. 1.2 Classification. The individual equipment belts shall be of the following sizes as specified (see 6.2). Medi

4、um - Waist under 30 inches Large - Waist 30 inches or over 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifi- cations, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specifie

5、d, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISSI and supplement thereto, cited in the solicitation (see 6.2). r I APSC N/A FSC 8465- DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimi

6、ted. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_I _II - - _ MIL-8-4382bC 4 7777706 0376302 5 MZL -B -4 3 8 2 6 C SPECIFICATIONS FEDERAL A-A-203 - Paper, Kraft, Untreated DDD-L-20 - Label: For Clothing, Equipage, and Tentage, (General PPP-B-636

7、- Boxes, Shipping, Fiberboard Use 1 MILITARY MIL-L-35078 - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection MIL-STD-129 - Marking for Shipm

8、ent and Storage MIE-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets by Attributes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: N

9、PODS), 5801 Tabor Avenue, Philadelphj.a, PA 19120-5099.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. are those cited in the solicitation. Unless otherwi

10、se specified, the issues DRAWINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 2-2-309 - Belt, Individual Equipment 2-2-498 - Belt Assembly (Copies of drawings are available from the U.S. Army Natick Research, Development, and Engineering Center, ATTN: STRNC-EMSS, Matick, MA 01760-

11、5014.) 2.2 Non-Government publications. The following document forms a part of this Unless otherwise specified, the issues document to the extent specified herein. of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified

12、, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). f 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-4382bC q 9999906 0396303 7 I MIL -E -4382 6C AMERICAN SOCIETY FOR TESTIN

13、G AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from the o

14、rganizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document take

15、s precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREtENTS 3.1 First article. When specified (see 6.21, a sample shall be subjected to first article inspection (see 6.3) in accordance with 4.3. 3.2 Guide

16、samples. Guide samples, when furnished, are solely for guidance and information (see 6,41. samples, in which case this document shall govern. Variations from the document may appear in the 3.3 Materials. The materials shall be as specified on Drawing 2-2-309 and all subsidiary drawings and parts lis

17、ts (PLS) pertaining thereto. It is encouraged that recycled material be used when practical as long as it meets the requirements of this specification. 3.4 Design and construction. The design and construction of the belt shall conform to the design, shape and dimensions shown on Drawing 2-2-309 and

18、(PLS) as specified herein. 3.4.1 Setting of eyelet with washer. Holes shall be prepunched or predrilled in the nylon webbing to receive the eyelets and shall be smaller than the outside diameter of the eyelet barrel so that the barrels must be forced through the holes. The eyelets with washer shall

19、be securely clinched in a manner that will prevent detachment from or cutting of the webbing, clinched without splitting. The eyelets shall be 3.4.2 Stitches, seams and stitching. All seams and stitchings shall be as specified on the drawings. 3.4.2.1 Automatic stitching. Automatic stitching machine

20、s may be used to perform any of the stitch patterns provided the requirements for the stitch pattern, stitches per inch, and size and type of thread are met; and at least three or more tying, overlapping or back stitches are used to secure the ends of stitching . 3 Provided by IHSNot for ResaleNo re

21、production or networking permitted without license from IHS-,-,-_ - MIL-B-4382bC 4 7777706 0376304 7 4 e MIL -B -4382 6C 3.4.2.2 Lubrication of thread. There shall be no lubrication of the thread prior to or during sewing (see 4.4.1.1). 3.4.2.3 Type 301 stitching. Ends of all stitching shall be back

22、stitched or overstitched as specified on the drawings except where ends are turned under or caught in other seams or stitching. Thread tensions shall be maintained so that there will be no loose stitching resulting in loose bobbin or top thread or excessively tight stitching resulting in puckering o

23、f the materials sewn. The lock shall be imbedded in the materials sewn. c 3.4.2.3.1 Repairs of type 301 stitching. Repairs of type 301 stitching shall be as follows: a. When thread breaks or bobbin run-outs occur during stitching, the stitching shall be repaired by restarting the stitching a minimum

24、 of 1/2 inch back of the end of the stitching. b. Thread breaks or two or more consecutive skipped or runoff stitches noted during inspection of the item (in-process or end item) shall be repaired by overstitching. The stitching shall start a minimum of 1/2 inch in back of the defective area, contin

25、ue over the defective area, and continue a minimum of 1/2 inch beyond the defective area onto the existing stitching. Loose or excessively tight stitching shall be repaired by removing the defective stitching without damaging the materials and restitching in the required manner. O (When making the a

26、bove repairs in a. and b. above, the ends of the stitching are not required to be backstitched.) 3.4.2.4 Thread ends. All thread ends that are visible on the finished item shall be trimmed to a maximum length of 1/4 inch. 3.4.3 Fusing of ends of nylon webbing. The ends of the nylon webbing shall be

27、fused smooth in such a manner as to prevent sharp edges from forming. apparatus used to fuse the webbing ends shall be capable of providing sufficient heat to fuse the cut ends of the webbing yarns together. The 3.4.4 Setting of snap fasteners. A hole shall be prepunched or predrilled through the ma

28、terials to receive the button and eyelet components of the snap fasteners. The hole shall be smaller than the outside diameter of the button and eyelet barrels so that the barrel must be forced through the hole. The hole shall not be punched in the setting operation with the button or eyelet barrel.

29、 The fasteners shall be securely clinched without cutting the surrounding materials and no more than three splits shall occur in the button or eyelet barrels. * 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-4382bC 4 7777706 0376305 O I MIL

30、-B-43826C 3.5 Label. The belt shall have a combination size and identification label. The label shall conform to type VI, class 5 of DDD-L-20 except that the print shall be a minimum of 10 point and the color of the label shall be medium green (see 6.5). The size and attachment location of the label

31、 to the belt shall be as shown on Drawing 2-2-498. The contents of the label may read either across the belt or along the belt, The information required for the size shall include the waist dimension, for example the information required for the size medium belt shall be llsize medium-waist under 30

32、 inches1. 3.5.1 Marking. The letters lrUSrr shall be applied in the size characters and in the location shown on Drawing 2-2-498 and shall conform to type IV, class 9 of DDD-L-20. Fastness for class 9 marking shall be as specified for class -5 marking. 3.6 Replacement of defective components. During

33、 the spreading, cutting and manufacturing process, components of the belt having material defects or damages that are classified as defects in table II shall be removed from production and replaced with non-defective and properly matched components. 3.7 Workmanship. The end item shall conform to the

34、 quality of product established by this specification. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specifi

35、ed herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of t

36、he inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specificatio

37、n shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply wi

38、th all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known . defective material, either indicated or actual, nor does it commit the Government

39、to accept defective material. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-4382bC 84 i 7777706 0396306 2 I MIL -B -4382 6C 4.1.2 Responsibility for dimensional requirements. Unless otherwise specified in the contract or purchase order, the

40、 contractor is responsible for ensuring that all specified dimensions have been met. When dimensions cannot be examined on the end item, inspection shall be made at any point, or at all points in the manufacturing process necessary to ensure compliance with all dimensional requirements. 4.1.3 Certif

41、icates of compliance. When certificates of compliance are submitted, the Government reserves the right to inspect such items to determine the validity of the certification. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article ins

42、pection (see 4.3). b. Quality conformance inspection (see 4.4). 4.3 First article inspection. When a first article is required (see 3.1 and 6.2), it shall be examined for the defects specified in 4.4.2 and 4.4.3. 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection

43、 shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection, In accordance with 4.1, components and materials shall be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this specific

44、ation or applicable purchase document. 4.4.1.1 Component and material certification. A certificate of compliance may be acceptable as evidence that the thread lubrication conforms to the requirement specified in 3.4.2.2. 4.4.2 In-process inspection. Inspection of subassemblies shall be made to ascer

45、tain that construction details specified in 4.4.2.1 and 4.4.2.2 which cannot be examined in the finished product are in accordance with specified requirements. The Government reserves the right to exclude from consideration for acceptance, any material or service for which in-process inspection has

46、indicated nonconformance. 4.4.2.1 In-process inspection of prepunched holes. Inspection shall be conducted to determine whether prepunching or predrilling requirements specified in 3.4.1 and 3.4.4 have been accomplished as specified. Whenever nonconformance is noted, correction shall be made to the

47、parts affected and lot in process parts which cannot be corrected shall be removed from production. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-B-43ZbC 4 M 77977Ob 037b307 4 a t MIL -B -4 382 6C 4.4.2.2 In-process dimensional inspection. I

48、nspection shall be conducted on belts prior to attaching the fabric keeper, buckle and sliding keeper to determine if location of eyelets and length of body after installation of eyelets, conform to specified dimensions on drawing 2-2-498. The lot size shall be expressed in units of belts. The sampl

49、e unit shall be one partly fabricated belt. The inspection level shall be S-3 (see 6.6). TABLE I. In process dimensional examination Classifica tion Examine Defect Major Minor Overall length Not as specified exceeding tolerances: of body - up to and including 1/4 inch 20 1 - by more than l/4 inch 101 Location of eyelets Any not located horizontally exceeding tolerances: - up to and including 1/8 inch 202 - by more than 1/8 inch 102 Any not