ARMY MIL-B-10154 C-1961 BATTERIES PRIMARY WATER-ACTIVATED (DUNK TYPE)《水激活电池组(浸泡型)》.pdf

《ARMY MIL-B-10154 C-1961 BATTERIES PRIMARY WATER-ACTIVATED (DUNK TYPE)《水激活电池组(浸泡型)》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-B-10154 C-1961 BATTERIES PRIMARY WATER-ACTIVATED (DUNK TYPE)《水激活电池组(浸泡型)》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、MILITARY SPECIFICATION 1 November 1961 SUPERSEDING MIL-B-10154B 10 April 1953 BATTERIES, PRIMARY, WATER-ACTIVATED (DUNK TYPE) This specification has been approved by the Department of Defense and is man- datory for use by the Departments of the Army, the Navy and the Air Force. - 1. SCOPE 1.1 Scope.

2、 - This specification covers primary batteries which are inert until immersed in or filled 1.2 Classification. - Batteries shall be of the following types, as specified (see 6.1): with water for specified periods of activation and are discharged in air. Type BA-253/U. Type BA-259/AM. Type BA-292/AM.

3、 Type BA- 31 6/AM. 1.2.1 .Type designation. - The type designation of water-activated primary batteries shall be in the fol- lowing form: T L Component (see i. 2.1. i) Battery type number (see 1.2.1.2) indicator (see 1.2.1. 3) 1.2.1.1 Component. - Primary batteries are identified by two-letter symbo

4、l “BA“ followed by a hyphen. 1.2.1.2 Battery type number. - The battery type number identifies the specific battery. 1.2.1. 3 Installation indicator. - The installation indicator is composed of one or .more letters preceded by a slant line, denoting the equipment with which the battery is associated

5、, as specified herein. /AM - Airborne meteorological equipment. /U - General utility (includes) two or more installation classes: airborne, shipboard, and ground. 2. APPLICABLE DOCUMENTS .* 2.1 The following documents, of the issue in effect on date of invitation for bids, form a part of this specif

6、ication to the extent specified herein: SPECIFICATIONS FEDELSAL QQ-B-626 - Brass, Leaded and Nonleaded; Rods, Shapes, Forgings and Flat Products With QQ-C-576 - Copper Plates, Rolled Bars, Sheets, and Strips. QQ-P-330 - Phosphor Bronze Bars, Plates, Rods, Sheets, Strips, Flat Wire, and Structural an

7、d Special Shaped Sections. UU-C-201 - Cardboard, Bristol, Manila, and Railroad. PPP-B-576 - Box, Wood, Cleated, Veneer Paper Overlaid. Finished Edges (Bars, Flat :Nire and Strips). I FSC 6135 I E- f ! /-/ . . . . . AtW Copyright Communications - Electronics Command Provided by IHS under license with

8、 CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-LOL54C bL m 9999906 0085637 4 m . . . - . 1 . MIL-B-10154C i - - - - . . -.-. ,._._._._. - ,.I . - . - . . -, , . -. . . . .- . .,_- _ ._- FEDERAL (contd. ) PPP-B-585 - Boxes, Wood, Wirebound. PPP-B-591 - B

9、oxes, Fiberboard, Wood-Cleated. PPP-B-601 - Boxes, Wood, Cleated-Plywood. PPP-B-621 - Boxes, Wood, Nailed and Lock-Corner. PPP-B-636 - Boxes, Fiber. PPP-C-96 - Cans, Metal, 28 Gage and Lighter. PPP-C-843 - Cushioning Material, Cellulosic. PPP-T-76 - Tape, Pressure-Sensitive Adhesive, Paper, Water Re

10、sistant. _._ . . - -.- . . MILITARY MIL-W-76 - Wire and Cable, Hook-Up, Electrical, Insulated. MIL-P-116 - Preservation, Methods of. MIL-T-713 - Twine and Tape, Lacing and Tying (for Use in Electrical and Electronic Equip- ment). MIL-P-3115 - Plastic-Material, Laminated, Thermosetting, Sheets, Paper

11、-Base, Phenolic Resin. MIL-S-6872 - Soldering Process, General Specification for. ML-L-10547 - Liners, Case, Waterproof. STANDARDS FEDERAL FED-STD-595 - Colors. MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes. MIL-STD-129 - Marking for Shipment and Storage. MIL-STD

12、-414 - Sampling Procedures and Tables for Inspection by Variables for Percent Defective. (Copies of specifications, standards, drawings, and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the con

13、- tracting officer. ) 2.2 Other publications, - The following documents form a part of this specification to the extent speci- fied herein. Unless otherwise indicated, the issue in effect on date of invitation for bids shall apply. NATIONAL BUREAU OF STANDARDS Handbook H28 - Screw-Thread Standards f

14、or Federal Services. (Application for copies should be addressed to the Superintendent of Documents, Government Printing Office, -Washington 25, D. C. CONSOLIDATED CLASSIFICATION COMMITTEE Uniform Freight Classification Rules. (Application for copies should be addressed to the Consolidated Classific

15、atiqn Committee, 1 Park Avenue at 33rd St., New York 16, N. Y. ) 3, REQIREMENTS 3.1 Preproduction inspection, - Prior to production, preproduction samples as specified (see 6.1) shall be forwarded to a laboratory satisfactory to the bureau or agency concerned for the tests specified in 4.5. 3.2 Mate

16、rial. - The material for each part shall be as specified herein. When a definite material is not specified, a suitable material shall be used. Acceptance or approval of any constituent material shall not be construed as a guaranty of the acceptance of the finished battery. form to Specification MlL-

17、W-76. 3.2.1 m. - When insulated wire is used for electrical connectors and terminal leads, it shall con- . . . : . . -y - - . . . , . , . . . I . . i . . . . . . ,. . . . ;:.: . . . . . i . . . ._.I. _-.-_-I_- - - _-. - _.-_-I_ ._-_-._I-. 1 _.-.- ._-_-_I- . .-a - . ,- ._.- . - . . . .-. - . ._ . - .

18、 .-.-. =- .I I. _._I._ - . . . . . . - 7.: ,. . _ . . i. _.I 1 . .,. _ 2 I Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-B-10154C 61 m 7777706 0085638 6 m n u(+/ / .e3 L7 M

19、IL-B-10154C 3.2.2 Brass. - Brass used for purposes other than internal construction of the cell shall conform to Specification QQ-B-626. 3.2.3 Copper. - Copper used for purposes other than internal construction of the cell shall conform to 3.2.4 Phosphor bronze. - Phosphor bronze used for purposes o

20、ther than internal construction of the 3.3 Design and construction. - The batteries shall be of the design, construction, physical dimensions, Specification QQ-(2-576. cell shall conform to Specification QQ-P-330. weight, voltages, and polarity specified (see 3. 7). The battery shall be constructed

21、for simple and rapid activation for service. The total time for activating and preparing the battery for use shall not exceed the specified time (see 3.7). 3.3.1 internal connections. - All connections shall be securely made. Connections between cells may be made with bare wire or suitable equivalen

22、t. Wire soldered to terminal lugs shall not be bared more than one-eighth of an inch from the lugs, nor extended more than one-eighth inch beyond the lugs. 3.3.2 Terminals. - The type, dimensions, and spacing of terminals shall be as specified (see 3.7). Terminals shall provide a positive means of m

23、aking and maintaining external electrical connections to the battery. Contact surfaces of the terminals shall not be obstructed by wax or other insulating compounds. 3.3.2.1 Socket-type terminals. - Contact portions of socket-type terminals shall be made of spring phosphor bronze or plated spring br

24、ass. Sockets shall be of such design, construction, and material as to minimize leakage, current between terminals and to prevent the short circuiting of terminals, or even mo- mentary contact of any of the pins of the mating plugs to any socket terminal other than those for which such pins are inte

25、nded. The socket shall provide a firm and positive contact with the pins of the mating plug. Unless otherwise specified (see 3.7), the pin-hole-spacing tolerances for socket terminals shall be plus or minus O. 005 inch, When the socket is not mounted directly on the battery jacket, it shall be conne

26、cted with cable (hook-up wire) conforming to type MW of Specification MIL-W-76. The wires leading from the battery to the socket shall be twisted or bound together to prevent shifting or unraveling, and the ends of the lacing twine, if used, shall be tied to prevent loosening. When lacing twine is u

27、sed for binding the wire together, it shall conform to type N, class 3 of Specification MIL-T-713. 3.3.2.2 Wire-lead terminals. - Unless otherwise specified (see 3.7), wire-lead terminals shall be of cable (hook-up wire) conforming to type MW of Specification MIL-W-76. The free end of each wire shal

28、l be bared for a distance of 1/2 f 1/8 inch. The strands of each wire so bared shall be twisted together and soldered. 3.3.2.3 Terminal markiws. - Terminal markings shall be as specified (see 3.7). Polarity, voltage, 3.3.3 Jackets. - The jacket is defined as the outer container housing the battery c

29、ontents. The jacket and unit of the battery (A, B, C) shall be legibly marked. shall be waterproof and fabricated in such a manner as to prevent its coming apart during activation or when subjected to any of the specified tests (see 4.7.5). jackets shall conform to lusterless green No. 34087 of Stan

30、dard FED-STD-595. 3.3.3.1 Color of jackets. - Unless otherwise specified (see 3.7), the color of all exposed surfaces of 3.3.4 Threaded parts. - All threaded parts shall be in accordance with Handbook H28. 3.4 Capacity and voltage. - When tested in accordance with 4.7.5, voltage of the battery. or a

31、ny unit of the battkry (in batteries composed of more than one unit), shall not exceed the maximum specified voltage nor fall below the specified test-end voltage within the time (capacity) specified. if limits of voltage fluctua- tions are specified, they shall not be exceeded (see 3. 7). 3.5 Label

32、ing and marking. - All labeling and marking shall remain clear and legible throughout all of the specified tests. The color of lettering shall be black. t:A . . 1 E-!;.: . L . .- . -. . . 4 1.: : J . - . l:. . . 1 p:L-.-:.- . E . . ) . ._.- . , - - - - . - -.- 1 . I . . . 1 ,-i. i I . I . . i i . .

33、. 4 . i I . _.-. - . . - . - . . -_._ -_- _ .-_ _-_ _- . -. . - . . I 3 Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-l I MIL-B-LOL54C 61 = 7777706 0085637 m. MIL-B-10154C 3.5.1

34、 Identification label. - Each battery shall have an identification label positioned as specified (see 3.7). Unless otherwise specified (see 3.7), there shall be no information on the label other than the follow- ing: Type designation Order number Code number Manufacturers name (Trade-mark may also b

35、e used) Example: I Battery BA-253/U Order number 0751 John Doe Company JODOC 8187-PHILA-51-1 5-16 The code number shown shall indicate the month and year of manufacture of 3.5.1.1 Code number. - the battery by means of a four-digit number in which the first two digits shall indicate the month and th

36、e last two digits the year. Months earlier than the tenth month shall be preceded by “O“. When a battery is com- pleted during the last ten working days of a month or the first ten working days of the subsequent month, the manufacturer is permitted to use either month as the coded month of manufactu

37、re. 3.5.1.2 Instruction label. - Each battery shall be provided with an instruction label, positioned as specified (see 3.7). The instruction label shall contain complete instructions for activating and preparing the battery for service. The instructions shall be approved by the bureau or agency con

38、cerned. 3.6 Workmanship. - The batteries shall be manufactured and processed in a careful and workmanlike manner in accordance with good design and sound construction. 3.6.1 Soldering. - Soldering operations shall be performed in accordance with Specification MIL-S- 6872. 3.7 Detail requirements. -

39、3.7.1 Type BA-253/U. - 3.7.1.1 Electrical and physical requirements. - The electrical and physical requirements shall be as follows: Nominal voltage Maximum voltage during discharge: At high and low temperature At normal temperature Test-end voltage Time for activation (maximum) Resistance load Term

40、inais . Weight (activated) . Droptest . Capacity and voltage tests (minimum time to reach test end voltage): initial low-temperature discharge initial high and low temperature discharge . initial normal temperature discharge. , -., 6. O volts 6.8 volts 7.9 volts 5.5 volts 15 minutes 12 ohms ,- Socke

41、t type 80 f 10 grams When tested as specified herein, battery suspension cord shall not rip or separate from its anchor- age, and battery shall not expe- rience any reduction in capacity. 45 minutes 45 minutes 32 minutes _.I . . *. . - . . I -. L ._.-. - ._ . . ,. . 1 . ,.-. _.-._.- - . . n. . . $ .

42、 . 1: . 1 . % . . . - i _ . .-. . -_. . _ . . ._ . . * .-._. . - . 1 i . .-. e-.-. . 3 1 -A:. _-. ._._. -. .rl . I . ,.- . .? . . ,._._.-_. . ._.- - . _._._ iI . - -. . .- . J i . . -. . - - -. -. . ./. . i . . . I NOTES: 1. All dimensions in inches. 2. Unless otherwise specified; tolerances are f 1

43、/32 on fractions. 3. Socket shall be No. 2636 Cinch Mfg. Corp., or equal. 4. Two holes 5/8 +1/16 diameter, one centered on each end -1/32 of the battery jacket. 5. Barrier to prevent activating water from short-circuiting _ the pins of socket. 6. Identification label, centered on side of battery. 7.

44、 instruction label, centered on opposite side of battery bearing identification label. 8. Twine shall be 2-1/2 i 1/2 long between knots and shall 9. Apply half hitch and pull both ends of twine tight before conform to type N, class 3 of Specification MIL-T-713. riveting in place. Figure 1 - Socket d

45、etail and wiring diagram for type BA-253/U. 8 5 - i -: : Copyright Communications - Electronics Command Provided by IHS under license with CRAINot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-10154C 61 777770b 0085641 b W Normal temperature 1.7 7.9 130. O MlL-

46、B-10154C After Test- activation end 1.1 1.1 5.5 5.5 95. o 95. o 3.7.2 Type BA-259/AM. - 3.7.2.1 Electrical and physical requirements. - The electrical and physical requirements shall be as follows: Unit 2 B Nominal 1.5 6 115 Voltage of unit I Maximum during discharge at High and low temperature I. 5

47、 7.4 130. O Minimum Time for activation: On open circuit . 10 minutes On closed circuit 15 minutes Total activation, maximum 25 minutes Resistance load: Alunit A unit Bunit .i Terminals Weight (activated), maximum Capacity and voltage tests (minimum time to reach initial low-temperature discharge .

48、Initial high and low temperature discharge . Initial normal temperature discharge Delayed low-temperature discharge Delayed high and low temperature discharge . Delayed normal temperature discharge , , . 10.00 f O. 06 ohms 28.80 f O. 14 ohms 3050 f 15 ohms Socket 450 grams test end voltage) 130 minutes 130 minutes 90 minutes 130 minutes 130 minutes 90 minutes Fluctua- tion- 1/ i o. o1 i .O5 fl.OO -. -.-.-.-.- - _ . . - . -.-. . . . . . . -During any of the discharge tests. 3.7.2.2 Socket detail and wiring diagram. - The socket detail and wiring diagram shall