ARMY MIL-B-10122 E-1991 BARGE LIQUID CARGO NONPROPELLED STEEL OFFSHORE 4 160-BARREL 120-FOOT DESIGN 231C《231C型设计 120英尺 160桶型 非推进式钢制远洋液体货物驳船》.pdf

《ARMY MIL-B-10122 E-1991 BARGE LIQUID CARGO NONPROPELLED STEEL OFFSHORE 4 160-BARREL 120-FOOT DESIGN 231C《231C型设计 120英尺 160桶型 非推进式钢制远洋液体货物驳船》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-B-10122 E-1991 BARGE LIQUID CARGO NONPROPELLED STEEL OFFSHORE 4 160-BARREL 120-FOOT DESIGN 231C《231C型设计 120英尺 160桶型 非推进式钢制远洋液体货物驳船》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-B-LO122E 19 m 9999906 0468328 3 m I INCH-POUND I MIL-B-l0122E(ME) 16 January 1991 SUPERSEDING - 19 October 1984 MIL-B-l0122D(ME) MILITARY SPECIFICATION BARGE, LIQUID CARGO: NONPROPELLED, STEEL, OFFSHORE, 4,160-BARREL, 120-FOOTJ DESIGN 231C Inactive for new design after 7 December 1989 This speci

2、fication is approved for use within the USA Belvoir Research Development, and Engineering Center, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers a liquid cargo, nonpropelled, steel barge. 2.

3、 APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications. standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwlse specified, the issues of these documents are those listed in the issue

4、of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: USA Belvo

5、ir Research, Development and Engineering Center, ATTN: STRBE-TSE, Fort Belvoir, VA 22060-5606 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 1930 DISTRIBUTION STATEMENT A. Approved for public release; distrib

6、ution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-LOL22E 39 W 9999906 0468329 5 SPECIFICATIONS FEDERAL TT- P - 664 UU-T-81 GGG-A-926 PPP-P-40 PPP - B - 601 PPP -B - 6 21 PPP-B - 636 MILITARY MIL- P - 116 MLL- B - 121 MIL- S -

7、196 MIL-L-2105 MIL-C-3131 MIL-F-3541 MIL-C-5501 MIL-E-10062 MIL-M- 11745 MIL-C-16173 MIL-F-16377 MIL-F-16377/53 MIL-F-16377/54 MIL-A-18001 MIL-T-22085 MIL-B-22191 MIL-L-23398 MIL-L-46010 - Primer, Coating, Alkyd, Corrosion-Inhibiting, Lead and Chromate Free. - Tag, Shipping and Stock. - Ax (Single B

8、it, Double Bit, Pick Head and Mattock Head). - Packaging and Packing of Hand Tools. - Boxes, Wood, Cleated-Plywood. - Boxes, Wood, Nailed and Lock-Corner, - Box, Fiberboard. - Preservation, Methods of. - Barrier Material, Greaseproofed, Waterproofed, - Support Items, Accessories, and Kits, - Lubrica

9、tion Oil, Gear, Multi-Purpose. - Cordage; Preparation for Delivery of. - Fittings, Lubrication. - Cap and Plug, Protective, Dust and Moisture Seal. - Engine, Preparation for Shipment and Storage of. - Marking and Labeling of U.S. Army Marine Craft. - Corrosion Preventive Compound Solvent Cutback, Co

10、ld Application. - Fixture, Lighting, Incandescent, General Lighting 100 Watts, 120 Volts, Dripproof 15 Degrees, Symbols 89 Slab, Disc - Tape, Adhesive, Preservation and Sealing. - Barrier Material, Transparent, Flexible, Heat - Lubricant, Solid Film, Air Cured, Corrosion - Lubricant, Solid Film, Hea

11、t-Cured, Corrosion Sealable. Inhibiting. Inhibiting. , , 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-B-LOL22E 39 m 9999906 O468330 I m MIL-A-46153 MIL-P-53030 STANDARDS MILITARY MIL-STD-105 MIL-STD-129 * MIL-STD-167-2 MIL-STD-769 MIL-STD-88

12、9 MIL-STD-1186 MIL-STD-1410 MIL-STD-1472 MIL-STD-1474 MIL - B - 10 12 2 E (ME) - Antifreeze, Ethylene Glycol, Inhibited, Heavy - Primer Coating, Epoxy, Water Reducible. Duty, Single Package. - Sampling Procedures and Tables for Inspection - Marking for Shipment and Storage. - Mechanical Vibrations o

13、f Shipboard Equipment by Attributes. (Recipr Mach . Exhaust piping shall be insulated in accordance with MIL-STD-769. Before lagging, insulation shall be secured by banding. Insulation and lagging shall contain no asbestos and certification to this effect shall be made available for review by the co

14、ntracting officer or the contracting officers representative. 3.10 Engine and carao pump. The cargo pump shall deliver 1,000 gallons per minute (GPM) against a total dynamic head of 183 feet without malfunction of the engine or pump, in accordance with MIL-STD-1410. 3.11 Lubrication. All surfaces re

15、quiring lubrication shall be provided with a means for lubricating. Bearings requiring grease and not served by central lubrication systems shall be provided with grease fittings conforming to MIL-F-3541. accessible to a grease gun. Pressure release devices shall be provided where the use of pressur

16、e lubricating equipment will damage grease seals or other parts. Fittings shall be located in a protected position and shall be 3.11.1 Lubricants. The barge machinery and equipment shall operate as specified herein when lubricated with military lubricants (see 6.3). 3.12 Human factors engineering. -

17、 Design of the barge shall conform with MIE-STD-1472 criteria, as applicable. Particular design attention shall be given, but not limited to, MIL-STD-1472, 4.0 (General), 5.1 (Controls/Display Integration), 5.2 (Visual Displays), 5.4 (Controls), 5.5 (Labeling), 5.6 (Anthropometry), 5.9 (Design for M

18、aintainability), 5.13 (Hazards and Safety), as applicable. 3.13 Identification marking. Unless otherwise specified on the drawings, the application or installation of designation markings, builders nameplate, load- line markings, draft marks, andgeneral marking and labeling throughout the barge shal

19、l conform to MIL-M-11745. 3.13.1 Instruction plates. The barge shall be equipped with instruction plates or diagrams, including warnings and cautions, descrbbing any special or important procedures to be followed in assembling, operating, or servicing, Instructions shall be on photographic plates of

20、 a size compatible with the information supplied and plate location. 3.14 Treatment and painting. The barge shall be cleaned, treated, and painted in accordance with TB 43-0144. be for mobilization. Finish paint on exterior surface shall 3.14.1 Skew and fender guards. Skegs and fender guards shall b

21、e treated for corrosion prevention by filling each skeg and guard with MIL-C-16173, grade 1 corrosive preventative compound, Then the compound shall be drained and the fill vent and drain plugs replaced. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

22、,-,-MIL-B-LO322E 19 9999906 0468336 2 3.15 Notice frames. Glazed frames for certificates, documents, or notices that are required by applicable regulatory bodies shall be furnished and installed. 3.15.1 Certificates. The following certificates shall be obtained and posted under glass in the machiner

23、y house of each barge: AMERICAN BUREAU OF SHIPPING Classification Certificate for Hull (*A1 05.1 Tank Barge). International Loadline Certificate. Letter stating full compliance with USCG requirements endorsed for the ,. carriage of liquids in grades B, C and D. , *. , 3.16 Technical publications. Su

24、ch technical publications as are specified shall be furnished (see 6.2 and 6.4). 3.16.1 Technical data. The contractor shall furnish and place the following data in the storage locker in the machinery house: a. b. Drawings. One print of each “as constructedtf drawing (see 6.5.1). c. Record of tests.

25、 One copy of each record of tests (see 6.5.2). d. e. Instruction books. One complete set of instruction books (see 6.5.4). Specification and drawings. drawings (see 3.1.1). One copy of this specification with design List of machinery and equipment. equipment (see 6.5.3). One copy of the list of mach

26、inery and 3.17 Repair parts. The on-board repair parts recommended by ABS and repair parts specified by the contracting officer shall be furnished (see 6.2):- 3.18 Storage of navigation liphts. - A locker for the storage of navigation lights and batteries shall be provided in the machinery house. sh

27、all be steel plate construction and designed to protect the components from damage. The locker 3.19 Tool box. A tool box shall be provided on the aft side of the machinery house. dimensions of 18 inches high X 18 inches wide X 48 inches long. be weather tight and equipped with a hinged lid and lock

28、hasp. be labeled “TOOLS“. The box shall be of steel plate construction having The box shall The box shall 3.20 Noise limits. 3.20.1 Noise levels. Noise levels produced by the barge shall comply with the requirements of MIL-STD-1474, with the exception of MIL-STD-1474, paragraphs 5.2, 5.3, and 5.4, a

29、nd except as indicated herein. 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-LOLZZE 19 W 9999906 04b8137 4 m a. The noise level at the operators positions, defined to be 18 inches from the engine, winch, pump or other control panels; and ot

30、her personnel occupied areas of the barge, defined to be anywhere within the machinery house and wherever personnel may be located on the deck, shall not exceed category D of table I (85 however, disassembly shall be limitad to those parts that can be removed and reinstalled without special tools or

31、 skilled personnel. Removed bolts, nuts, pins, screws, and washers shall be reinstalled to mating parts and secured to prevent their loss. 5.1.1.2 Natch-marlrlng. Removed parts and mating parts remaining on the barge shall be matchmarked when necessary to facilitate reassembly. marking information s

32、hall be marked on cloth shipping tags conforming to W-T-81, type A, grade optional and the marked tags shall be attached to mating parts with wire or twine. The tags shall be marked with waterproof ink. Alternatively, the match-marking may be accomplished by stenciling with gasoline-soluble paint. I

33、tems too small to be effectively tagged or stenciled shall be matchmarked by affixing the identification information on an exterior Match- wrap or container as applicable: O 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-LOL22E 19 9799906 0

34、4bL43 T 5.1.1.3 Preservatives, The provisions of MIL-P-116 shall apply when selecting and when determining the applicability of preservatives. preservatives are specified herein by iIPtt numbers, they shall conform to the applicable specifications listed in MIL-P-116 and shall be applied in accordan

35、ce with MIL-P-116. When 5.1.1.4 Unfinished (not machined) surfaces, Unfinished exterior metal surfaces shall be coated with type P-1 preservative. 5.1.1.5 Machined surfaces, Exposed machined surfaces shall be coated with type P-6 or P-11 preservative and wrapped or covered, as applicable, with barri

36、er material conforming to MIL-B-121, type I or II, grade A, class 2 or MIL-B-22191, type II. The material shall be secured in place with tape conforming to MIL-T-22085, type II. 5.1.1.6 Exposed gears. Exposed gears shall be coated with type P-1 preservative or with primer conforming to TT-P-664 or M

37、IL-P-53030. 5.1.1.7 Enclosed gears. Gears operating on lubrication oil (SAE 10, 30, or 50) shall have the housing filled to the operating level with type P-10 preservative, type I, grade 10, 30, or 50 as applicable and tagged to indicate: “The preservative oil is adequate for operation. Do not drain

38、 until the first required lubrication change.“ lubricant (SAE 80 or 90) shall be filled to the operating level with lubricant conforming to MIL-L-2105, grade as applicable, and tagged to indicate: “The lubricant is good for operation. Do not drain until the first required lubrication change.“ Gears

39、not operating on lubrication oil (SAE 10, 30, or 50) or lubricant (SAE 80 or 90) shall be filled to the operating level with the approved lubricant required for operation. tagged to indicate: “The housing is filled to the operating level with the applicable type lubricant. lubrication change.“ The t

40、ags shall conform to W-T-81, type A. Information on the tags shall be applied with waterproof ink. The tags shall be attached in a conspicuous location, Gears operating on gear The gear housings shall be Do not drain prior to the first required 5.1.1.8 Exposed drive chains. Exposed drive chains shal

41、l be coated with enough type P-3 or P-9 preservative to insure penetration of the preservative to the inner surfaces of the rollers, pins, and bushings. After the excess preservative has drained, the entire chain and the unpainted surfaces of the sprocket shall be coated with type P-1 preservative.

42、5.1.1.9 Enclosed chains, Enclosed chains and chain housings shall be preserved and tagged as specified in 5.1.1.7 for enclosed gears. 5.1.1.10 Drive belts and pullevs. Drive belts shall be removed or released from tension. method IC-1 or IC-3. Unpainted faces of pulley grooves shall be coaeed with p

43、rimer conforming to TT-P-664 or primer conforming to MIL-P-53030. conforming to -T-81, type A, shall be attached in a conspicuous location Removed belts shall be preserved in accordance with MIL-P-116, A tag 16 a ,. , 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without lic

44、ense from IHS-,-,-MIL-B-LO122E 19 9999906 0468144 1 indicating: “Belts have been removed or released from tension. Install or tension as applicable, prior to operation.“ be applied with waterproof ink. The information on the tag shall 5.1.1.11 Drive shafts and universal ioints. Unpainted surfaces of

45、 drive shafts and universal joints shall be coated with type P-1 Preservative. boots, if furnished, shall be reinstalled. Dust 5.1.1.12 CarJzo discharge pump and piping. The cargo discharge pump and cargo discharge and distribution piping systems shall be -Lushed with type P-10, type II, grade 30, p

46、reservative oil. All excess preservative oil shall be allowed to drain. Drain cocks and drain valves, as applicable, shall be left open. plugs conforming to ML-C-5501, or with pressure sensitive tape conforming to MIL-T-22085, type II. All valves shall be injected with the proper amount of sealant n

47、ecessary to provide a sealant film between the tapered plug and body All other openings shall be sealed closed with plaseic caps or 5.1.1.13 Gamo tanks. All interior surfaces of the cargo tanks shall be coated with P-10, type II, grade 30, preservative oil. 5.1.1.14 Fuel tank, Interior surfaces o eh

48、e fuel tank requlring a preservative (see 5.11.3), shall be fogged with preservative lubricating oil conforming to P-10, type II, grade 10. Excessive preservative shall be allowed to drain. Drain cocks and drain valves shall be left open. All other openings shall be sealed with plastic caps or plugs

49、 conforming to MIL-C-5501 or with pressure sensitive tape conforming to MIL-T-22085, type II. Fuel filters, strainer, and lines shall be clean and in operating condition. 5.1.1.15 Other void areas. Other void areas not specifically provided or herein shall be clear of waste, free of foreign material, drained, and dry,. 5.1.1.16 Engine. Engine, engine components, and engine accessories shall be preserved in accordance with level A requirements of MIL-E-10062