ARMY KK-C-300 C-1969 CHAMOIS LEATHER SHEEPSKIN OIL TANNED《油鞣羊皮革》.pdf

《ARMY KK-C-300 C-1969 CHAMOIS LEATHER SHEEPSKIN OIL TANNED《油鞣羊皮革》.pdf》由会员分享，可在线阅读，更多相关《ARMY KK-C-300 C-1969 CHAMOIS LEATHER SHEEPSKIN OIL TANNED《油鞣羊皮革》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、. KK-C-300C 83 7979774 0058877 7 W Junf-:3G1969J “ SUPERSEDING Fed. Spec. KK-C-300bv February 13, 1964 I FEDERAL SPECIFICATION CHAHOIS LEATIIER, SHEEPSKIN, OIL TANNED This specification was approved by the Commissioner, Federal Supply Service, General Services Administration, for the use of all Fede

2、ral agencies. i 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification covers the requirements for chamois leather made from oil-tanned sheepskin fiechers, 1.2 Classification. 1.2.1 Grades, classes, and sizes. Chamois leather shall be of the following and sizes, as specified (6.2). Grade A - For

3、straining water and other impurities from gasoline. Grade B - General purpose (washing and polishing). Class 1 - Packet-shaped. . Size 12 X 14 inches. Size 16 X 21 inches. Size 20 X 26 inches. Size 23 X 26 inches. Class 2 - Natural skin-shaped, edges trimmed. Size S - Small. Size M - Medium. Size L

4、- Large. 2. APPLICABLE DOCME“S grades, classes, 2.1 Specifications and standards. effect on date of invitation for bids or request for proposal, form a part of this specification to The following specifications and standards of the issue in the extent specified herein: Federal Specifications: w-P-26

5、8 - Paper, Kraft, Untreated, Wrapping. ppp-B-636 - Box, Fiberboard. PPP-F-320 - Fiberboard; Corrugated and Solid, Sheet Stock PPP-T-45 - Tape, Gummed, Paper, Reinforced and Plain, for (Container Grade), and Cut Shapes. Sealing and Securing. Federal Standards : Fed. Std. No. 311 Fed. Std. No. 123 - L

6、eather, Methods of Sampling and Testing. - Marking for Domestic. Shipment (Civilian Agencies) + FSC 8330 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ KK-C-300C 3 W 7777774 0058700 I , KK-C-30CC (Activities outside the Federal Government may obta

7、in copies of Federal Spkcifications, Standards and Handbooks as outlined under General Information in the index of Federal Specifications and Standards, and at the prices indicated in the Index, which includes cumulative monthly supplements as issed, is for sale on a subscription basis by the Superi

8、ntendent of Documents, U. S. Government Printing Office, Washington, D.C. 20402.) (Single copies of this specification and other Federal specifications required by activities outside the Federal Government for bidding purposes are available without charge from the Business Service Centers at the Gen

9、eral Services Administration Regional Offices in Boston, New York, Washington, D,C, Atlanta, Chicago, Kansas City, Mo., Fort Worth, Denver, San Francisco, Los Angeles, and Seattle, Washington.) (Federal Government activities may obtain copies of Federal Specifications, Standards, and Handbooks and t

10、he index of Federal Specifications and Standards from established distribution points in their agencies.) Military Standards: MIL-STD-105 - Sampling Procedures and Tables for 1nspection.by MIL-STD-129 - Marking for Shipment and Storage, Attributes, (Copies of Military Specifications and Standards re

11、quired by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer. ) 2.2 Other publications, The following documents form a part of this specification to the extent specified herein. Unless otherwise indic

12、ated, the issue in effect on date of invitiation for bids or request for proposal shall apply: 1 .c National Classification Board: National Motor Freight Classification Rule I (Application for copies should be addressed to the National Classification Board, 1616 P Street, N.W. , Vlashington, D.C. 20

13、036. ) Uniform Classification Committee: Uniform Freight Classification Rule. (Application for copies should be addressed to the Uniform Classification Committee, 202 Union Station, Chicago, Illinois 60606, ) 3. REQUIREMENTS 3.1 Material;. The chamois leather shall be made from the flesh splits of s

14、heepskins split before tanning. leather. 3.2 Tannage. The flesh splits shall be oil tanned so as to produce a soft absorbent chamois 3,3 Physical requirements. 3.3,1 Trim (form and area), 3.3.1.1 Class 1. The class 1 chamois shall be rectangular except the corners of the upper end shall be rounded t

15、o form a pocket shape, sizes indicated, The area of the chamois shall be as specified below for the Size, inches 1/ Area, square inches, minimum 12 X i4 145 20 x 26 460 23 X 26 520 16 x 21 290 1/ 2 A tolerance of -1/2, +: 2 inches shall be permitted in the width and length dimensions, Provided by IH

16、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-KK-C-300C 3 7997774 005703 3 W KK-c-3ooc 3.3.1.2 Class 2. to remove al$ ragged and unserviceable edges., The area of the chamois shall be as specified below for the sizes indicated. The class 2 chamois shall be in th

17、e form of whole skins which have been trimmed - Size Area, square inches, minimum Small Nedium Large 450 575 675 3.3.2 Finish. The chamois shall be suede-finished on both sides. 3.3.3 m. The color of the chamois shall be natural as produced by the oil tannage. The chamois shall not be chemically ble

18、ached or dyed. 3,3.4 Tnickness. The chamois shall be not less than 1-1/4 ounces in thickness. NOTE: 1 ounce = 1/64 inches. 3.3.5 Breaking force. 3.3.5.1 Grade A. The breaking force of the grade A chamois shall be not less than 40 pounds when tested as specified in 4.3. 3.3.5.2 Grade B. The breaking

19、force of the grade B chamois shall be not less than 30 pounds when tested as specified in 4.3. 3.3.6 Water absorption. 3.3.6.1 Grade A. The grade A chamois shall gain not less than 450 percent of its conditioned weight by water absorption when tested as specified in 4.3. . weight by water absorption

20、 when tested as specified in 4.3. 3.3.6.2 Grade B. The grade B chamois shall gain not less than 375 percent of its conditioned 3.3.7 Water removed by wringing. 3.3.7.1 Grade A. The amount of water expelled from the chamois by wringing shall be not less than 250 Gercent of the weight of the condition

21、ed specimen when tested as specified in 4.3. 3.3.7.2 Grade B. 3.3.8 Gasoline-water separation (grade A). The amount of water expelled from the chamois by wringing shall be not less than 200 percent of the weight of the conditioned specimen when tested as specified in 4.3, The chamois shall remove wa

22、ter in a water-gasoline mixture when tested as specified in 4.3. chamois shall not exceed one minute when tested as specified in 4.3. The time required for the gasoline to pass through the 3.3.9 Time of wetting (grades A and B). The time of wetting of the chamois shall be no greater than 30 seconds

23、when tested as specified in 4.3. 3.4 Chemical requirements, The chamois leather shall conform to the chemical requirements of table I when tested as specified in 4.3. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-KK-C-30OC 83 M 999997L1 0058902 5

24、 sl KK-C -3OOC TABLE I. Chemical requirements Character ist ic Total ash, percent I/ Iron and aluminum oxides, percent Chromic oxide, percent Free formaldehyde, percent G Minimum pH value u Calculated on the moisture free basis. 6.5 le A Maximum 8.0 1.0 0.3 . 0.05 - Gr: Minimum - 6.5 B Maximum 12.0

25、1.5 0.3 0.05 3-5 Markine, 3,5.1 Description, Each class 1 chamois shall be marked along the base edge (opposite rounded edge) and each class 2 chamois shall be marked along the butt edge so as to exhibit the following information: Chamois Leather - Grade A (or B as applicable) Contract No. Size Lot

26、No. /- The bottom line shall be 1f 1/2 inches from the base or butt edge. inch in height and of a contrasting color to the chamois. markings shall be located on the side of the chamois from which the grain has been removed (rough side of chamois). The lettering shall be 3/8 f 1/8 Unless otherwise sp

27、ecified (see 6.2), all 3.5.2 Grade designation. In addition Go the lettering described in 3.5.1 and approximately four inches above it, each grade A chamois shall be marked “FILTERING TYPE“ and each grade B chamois shall be marked “NON-FILTERING TYPE“, 3.5.3 Tanners brand or trademark. Letter size a

28、nd color shall be as described in 3.5.1. In addition to the markings described in 3.5.1 and 3.5.2 and in a position approximately midway between them, each chamois unit shall carry the identifying name or trademark of the tanner. 3.5.4 Unless otherwise specified, in addition to the marking described

29、 in 3.5.1 and approximately six inches above it , each grade B chamois shall be legibly and permanently marked “U.S. Property“. Letter size and color shall be as described in 3.5.1, 3.6 mit up (class 2). 3.6.1 Military requirements, Class 2 chamois units shall be supplied in multiples of 5 units, wh

30、ich seail consist of a minimum of 20 percent size Large and 40 percent size Medium, and a maximum of 40 percent size Small, sizes, 3.6.2 Civilian re uirements. At the option of the contracting officer, class 2 chamois units shall be supplied in kltiples of 5 units, in accordance with the percentage

31、distribution in 3.6.1, or in individual sizes as specified (see 6.2). 3.3.1.2 for the respective sizes, The area of the units shall be as specified in 3.3.1.2 for the respective “he area of the units shall be as specified in 4 Provided by IHSNot for ResaleNo reproduction or networking permitted with

32、out license from IHS-,-,-KK-C-300C 3 9999474 0058903 7 W KK-C-30CC 3.7 Workmanshie. The finished chamois shall conform to the quality and grade of product established by this specification. levels, Occurrence of defects shall not exceed the applicable quality 4. QUALITY ASSURANCE PROVISIONS 4,l Resp

33、onsibility for inspection. Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the supplier may use his own or any other facilities su

34、itable for the performance of the inspection requirements specified herein, unless disapproved by the Government, set forth in the specification where such inspecifications are deemed necessary to assure that supplies and services conform to prescribed requirements. The Government reserves the right

35、 to perform any of the inspections 4.1.1 Certificate of compliance. Where certificates of compliance are submitted, the Government reserves the right to check test such items to determine the validity of the certification. 4.2 Inspection. Sampling for inspection shall be performed in accordance with

36、 MIL-STD-105, except where otherwise indicated hereinafter. 4.2.1 Component and material inspection, In accordance with 4.1 above, components and materials shall be tested in accordance with all the requirements of referenced specifications, drawings and standards unless otherwise excluded, amended,

37、 modified, or qualified in this specification or applicable purchase document. 4.2.2 Examination of the end item. The classification of defects found during the examination shall be in accordance with the lists shown in 4.2.2.1 and 4.2.2.2. examinations shall be one chamois. inspection levels and ac

38、ceptable quality levels (AQL) for these examinations shall be in accordance with 4.2.2.3. The sample unit for these The lot size shall be expressed in units of one chamois. The 4.2.2.1 Examination for visual characteristics. Examine Material Finish Color Tr im Grades A and B: Class 1 Class 2 Quality

39、 . Grade A: and 2 Classes 1 Defect Not flesh split. Suede finish completely missing from one or both sides. Not natural color, Le., the skin is dyed or bleached. Not pocket-shaped, i.e., not rectanmar with upper corners rounded. Not natural skin shape. Ragged or unserviceable edges. Cockle, hard sca

40、rs or hard spots with cumulative total area of more than 2 square inches per unit. Any hole, cut or tear. Thin spot. Cemented or sewn pieces. Classi. Ejr X X X X X :ation Minor - X X X X X 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-KK-Cy30CC K

41、K-C-300C 83 W 9999974 0058904 9 W * r Examine Size and area: Examine Quality (cont d) Grade B: and 2 Classes 1 Defect Marking Defect Cockle, hard scars or hard spots exceeding 4 square inches in total area. 1/4 inch or less in longest dimension. than 1/4 inch in longest dimension, Two or more holes,

42、 cuts or tears One hole, cut or tear greater Cemented or sem pieces. Missing, incorrect, illegible or not located as specified. 4.2.2.2 Examination for dimensional characteristics. Classification Major Minor X X A X X Class 1 Class 2 Length or width not as specified, I./ Area of unit less than speci

43、fied, 2/ Area of unit less than specified. 2f Not as specified. 3/ I Thic kne s s I/ The length of the unit is the longest dimension (not diagonal) j the width is the widest dimension perpendicular to the length. 2/ The area shall be determined in accordance with methods 1111 or 1121 of Fed, Sed. No

44、. 311, except that the area shall be reported to the nearest square inch. When method 1121 is used tne area shall be recorded to the nearest 50 square centimeters. For reporting purposes the area shall be coverted to square inches by multiplying the total area recorded in square centimeters by 0.155

45、. Thickness of class 2 and class 2 chamois shall be determined in accordance with method 1011 of Fed Std. No. 311 except that the thickness of class 1 chamios shall be measured at 5 points equally spaced along the length dimension. minimum specified. 3/ No single measurement shall be less than the 6

46、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.2.2.3 Inspection levels and AQLs, per hundred units, shall be as follows: The inspection levels and Aas, expressed in defects Examinat ion For defects applicable to 4.2.2.1, visual character- istics:

47、 Grade A. . . . , . . . e Grade B. . . . , . , , . For defects applicable to 4.2.2.2, dimensional characteristics. Inspection level ABL II Major * Total 2.5 II Major 2.5 Total 6.5 s -3 4.0 Examine Marking (exterior and interior) Materials Workmanship Content Defect Omitted; incorrect; illegible; of

48、improper size, sequence, or method of application. Any component damaged, Any component missing. Inadequate application of components such as incomplete closure of container flaps, improper taping, loose strapping, inadequate stapling. Bulged or distorted container. Number of bundles per shipping co

49、ntainer is more or less Number of chamois per bundle is more or less than Multiple units for class 2 chamois, when applicable, than required. required, r/ not in size percentages specified. I/ J For these defects, two bundles shall be examined from each shipping container in the sample. 4.3 End item testin .The methods of testing sp_cified Fed. Std. NO. 3U wherever applicable and as listed in table II shall be followed. The sample unit for testing shall