ARMY A-A-59785-2005 EPOXY COATING KIT (EPOXY RESIN SYSTEM)《环氧树脂涂料套件(环氧树脂体系)》.pdf

《ARMY A-A-59785-2005 EPOXY COATING KIT (EPOXY RESIN SYSTEM)《环氧树脂涂料套件(环氧树脂体系)》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-59785-2005 EPOXY COATING KIT (EPOXY RESIN SYSTEM)《环氧树脂涂料套件(环氧树脂体系)》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 METRIC A-A-59785 9 DECEMBER 2005 COMMERCIAL ITEM DESCRIPTION EPOXY COATING KIT (EPOXY RESIN SYSTEM) The General Services Administration has authorized the use of this Commercial Item Description by all federal agencies. 1. SCOPE. This commercial item description (CID) covers a two part epoxy resin

2、system suitable to be used in the production of advanced composite materials. 2. SALIENT CHARACTERISTICS. 2.1 General. The Epoxy Resin System is a two component resin system for use in the production of advanced composites. The two components include the epoxy resin and a hardener used for curing th

3、e final product. When the two parts (resin and hardener) mix together, they react, and join together. The advanced composite manufacturing infusion processes in which the described Epoxy Resin System could be used include Resin Transfer Molding (RTM), Vacuum Assisted Resin Transfer Molding (VARTM),

4、Seemans Composite Resin Injection Molding Process (SCRIMPTM), prepreg hand lay-up, and/or other infusion processes. The manufacturers formulated mix ratio, measuring out by weight and volume, shall be followed to ensure the complete reaction of the resin and hardener. 2.1.1 Performance Requirement.

5、Unless otherwise noted, the epoxy resin system shall meet or exceed the performance criteria in Table I. when tested at 77F (25C). TABLE I. PropertiesProperty Criteria ASTM Test Method Value Specific Gravity (Approximate) Resin Hardener D-792 1.1 0.94 Viscosity, cP (or less) Resin Hardener Mixed D-2

6、393 1200 100 500 - 700 Gel time, minutes 100 gm D-2471 480 - 580 Temperature (Max.) 300F (149C) after heated postcure Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any other data which may improve this document should be sent by letter to: US Army Tank-automot

7、ive and Armaments Command, ATTN: AMSRD-TAR-E/268, 6501 E. 11 Mile Road Warren, MI 48397-5000. AMSC N/A FSC 8010 Distribution Statement A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5978

8、5 2 TABLE II. Neat SystemProperty ASTM Test Method Value Specific Gravity (Approximate) D-792 1.06 Hardness (Shore D) (Approximate) D 2240 89 Ultimate Tensile Strength, psi (Approximate) D 638 6921 Tensile Modulus, psi (Approximate) 366555 % Elongation (Approximate) 2.5 Tg by DMA, E onset, dry, F (C

9、) (Minimum) D - 4065 307 (153) Tg by DMA, E onset, wet, F (C) (Minimum) D - 4065 270 (132) NOTES: 1. Tested 77F (25C) unless otherwise noted. 2. All properties are of neat product form (non-composite). Similar cure cycle and temperature, mixing ratio, and homogeneity of mixing have to be used for th

10、e test coupons and product manufacturing. 3. REGULATORY REQUIREMENT. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE. 4.1 Product Conformance. Th

11、e products provided shall meet the salient characteristics of this Commercial Item Description, conform to the producers own drawings, specifications, standards and quality assurance practices and be the same product offered for sale in the commercial marketplace. The government reserves the right t

12、o require proof of such conformance. 4.2 Market Acceptability. The product shall be a standard commercial item or a modified commercial item to minimize design and engineering risk. A commercial item is required to ensure serviceability, reliability and quality of materials. Bid samples may be requi

13、red for the Epoxy Resin System to ensure product quality. 5. PACKAGING. Preservation, packaging, packing and marking shall be specified in the contract of purchase order. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59785 3 6. NOTES 6.1 Source

14、 of Documents.6.1.1 The Code of Federal Regulations (CFR) may be obtained from the US Government Printing Office, 732 Capitol Street NW, Washington, DC 20401 or at their website http:/www.gpoaccess.gov/cfr/index.html 6.1.2 ASTM Standards are available from the ASTM International, 100 Bar Harbor Driv

15、e, West Conshohocken, PA 19428-2959 or from their website at http:/www.astm.org 6.2 Ordering data. The contract or order should specify the following: a. CID Document Number b. Product conformance provisions c. Packaging Requirements 6.3 Products known to meet the CID. a. RenShape Solutions Resinfus

16、ionTM 8605 Epoxy Resin System Available from: Huntsman Advanced Materials 4917 Dawn Avenue, East Lansing, MI 48823. 6.4 Key words. Epoxy Resin MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS Custodians Army AT Preparing Activity: Navy AS Army AT Air Force 11 (Project 8010-2006-007) Review Activities Army MI, MR, Navy CG, SH Air Force 84, 99 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-