ARMY A-A-59276-1998 WOOD PRESERVATIVES WATERBORNE OR WATER REDUCIBLE《木材防腐剂 水性或水还原》.pdf

《ARMY A-A-59276-1998 WOOD PRESERVATIVES WATERBORNE OR WATER REDUCIBLE《木材防腐剂 水性或水还原》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-59276-1998 WOOD PRESERVATIVES WATERBORNE OR WATER REDUCIBLE《木材防腐剂 水性或水还原》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、2. NOT MEASUREMENT SENSITIVE A-A- 5 9276 29 June 1998 SUPERSEDING MIL-W-71125 (AR) COMMERCIAL ITEM DESCRIPTION WOOD PRESERVATIVES: WATERBORNE OR WATER REDUCIBLE The General Services Administration has authorized the use of this commercial item description, for all federal agencies. 1. SCOPE. 1.1 Thi

2、s CID covers the general requirements for ready-to-use, aqueous solutions, dispersions or emulsions for preservative treatment of wood by non- pressure methods, primarily for use in the treatment of wood pallets, containers, and packing materials. 2. CLASSIFICATION. 2.1 Waterborne wood preservatives

3、 covered by this Commercial Item Description shall be of the following compositions: Composition E - Zn naphthenate Composition F - Cu naphthenate Composition G - Copper-8-quinolinolate 3. SALIENT CHARACTERISTICS. 3.1 Materials. The composition and quantity shall be supplied as specified in the cont

4、ract or order (see 7.3). 3.1.1 Comoosition E. The treating solution containing Zn naphthenate shall be an emulsion of Zn naphthenate and shall contain not less than 3%, by weight, of Zn in accordance with AWPA A9 or AWPA All. Beneficial comments (recommendations, additions, deletions) and any pertin

5、ent data which may be of use in improving this document should be addressed to: Commander, US Army TACOM-ARDEC, Attn.: AMSTA-AR-EDE-S, Bldg 12, Picatinny Arsenal, NJ 07806-5000 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by lette

6、r. msc N/A 8030 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesA-A-5 9276 3.1.2 ComDosition F. The treating solution containing Cu naphthenate shall be either an aqueous solution, dispersion or emulsipn of Cu naphthenate and

7、 shall contain not less than 2%, by weight, of Cu in accordance with either AWPA AS, AWPA A9, or AWPA All. 3.1.3 ComDosition G. The treating solution containing Cu-8-quinolinolate shall be an aqueous solution of dodecylbenzene sulfonic acid (DDBSAI-solubilized Cu 8-quinolinolate and shall contain no

8、t less than 1.8% copper-8-quinolinolate, by weight, in accordance with either AWPA A5, AWPA A9, or AWPA All. 3.2 Drvincr time. The treating solution on the surface of the treated wood shall not be tacky within 72 hours after treatment. 3.3 Corrosion. Wood preservatives shall create no chemical react

9、ion, with any hardware used in packaging design, that would cause pitting or oxidation. 3.4 Color. The color of the solution shall be sufficiently clear as not to change the color of the wood when the solution is applied; however, it should be noted that Compositions F and G impart a green color to

10、the wood. 3.5 Solvents. The principal carrier for treating solutions shall be water. Where emulsions or dispersions of organic materials in water are used, the organic solvent“ preservative. A dispersing agent is defined as the substance, when mixed with the preservative concentrate, causes the pres

11、ervative concentrate to disperse easily when mixed with water. Organic solvents shall be sufficiently pure so they do not cause any objectionable odor or cause the treated material on which it is applied, to have objectionable odors or irritation. is defined as the solvent for the organic wood 3.6 P

12、reservative effectiveness. All compositions shall provide a minimum of 2 years protection, when applied to an untreated wood surface with one single application, under uncontrolled exposure, in temperate and tropical environments. Accelerated aging of wood preservatives shall be determined by testin

13、g in accordance with ASTMD-822-96. 3.7 Registration. All preservatives shall be registered with the Environmental Protection Agency (EPA) and must be used in accordance with the EPA label. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum exte

14、nt practicable, in accordance with paragraph 23.403 of the Federal.Acquisition Regulation (FAR). 5. QUALITY ASSURANCE PROVISIONS. 5.1 Product Conformance. The products provided shall meet the salient characteristics of this commercial item description (CID), conform to the producers own drawings, sp

15、ecifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5.2 Market accemabiiitv criteria. The item offered must have been sold to the government or commercial

16、market. 2 Licensed by Information Handling Services1 A-A-59276 9018054 0002965 647 A-A- 5 92 76 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 Parts Identification Number (PIN). The following part identification number (PIN) procedure i

17、s for government purposes and does not constitute a requirement for the contractor. The PINS to be used are as follows: AA Xxxxx-x -Cornposit ion CID Number CID Designator 7.2 Source of Documents. 7.2.1 The Code of Federal Regulations (CFR) is available by mail order from the Superintendent of Docum

18、ents, ATTN: New Order, PO Box 371954, Pittsburgh, PA 15250-7954. 7.2.2 ASTM standards are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. 7.2.3 AWPA Standards are available from the American Wood-Preservers Association, 3246 Fal

19、l Creek Highway, Suite 190, Granbury, TX 76049-7979 7.3 Orderins Data. Procurement documents should specify the following: a. Title, number, and date of this CID. b. Issue of Department of ,Defense Index of Standards and Specifications (DODISS) to be cited in the solicitation, and if required, the s

20、pecific issue of individual documents referenced. c. Composition and quantities desired (see 3.1). d. Packaging and marking requirements (see 6). 7.4 Material Safetv Data Sheets (MSDS). Products meeting the requirements of this CID may be subject to the requirements of 29 CFR 1910.1200 and FED-STD-

21、313 for Material Safety Data Sheets. 7.5 Hazardous material. Products meeting the requirements of this CID may be subjected to the requirements of 49CFR 107 and other applicable provisions. 7.6 Toxicolosical data. Toxicological product formulations and associated information may be required for revi

22、ew by the contracting activity to evaluate the safety of the material for the purpose used. ASTM D-5276-94 may be used in connection with any packaging design for this evaluation as determined by the contracting activity. 7.7 Treatments. The preservative covered by this CID is normally used to provi

23、de a moderate degree of protection when an item is exposed to wetting. It is not generally used to provide long term protection under severe exposure to wetting. 3 Licensed by Information Handling Services _ A-A-5927b W 7038054 0002966 583 A-A-59276 7.8 Subiect term (key word) listinq. Sealing Compound Aqueous solution , Water resistant coatings Protective coating MILITARY INTERESTS: Custodian: Army-AR Review Activity: Army-MR CIVIL AGENCY COORDINATING ACTIVITY: GSA- FSS Preparing Activity: Army-AR Project 8030-0763 4 Licensed by Information Handling Services