ARMY A-A-52491-1994 BEARING BALL THRUST INCH AND METRIC SIZES GROOVED RACE SURFACE RIGID OR FLAT SEAT TYPE《英寸和公尺的坚硬表面的有沟座圈或平座型推力球轴承》.pdf

《ARMY A-A-52491-1994 BEARING BALL THRUST INCH AND METRIC SIZES GROOVED RACE SURFACE RIGID OR FLAT SEAT TYPE《英寸和公尺的坚硬表面的有沟座圈或平座型推力球轴承》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-52491-1994 BEARING BALL THRUST INCH AND METRIC SIZES GROOVED RACE SURFACE RIGID OR FLAT SEAT TYPE《英寸和公尺的坚硬表面的有沟座圈或平座型推力球轴承》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-52491 W 9999974 0364257 707 INCH-POUND A-A-52 49 1 April 15, 1994 SUPERSEDING MS 1 7 1 6 1C 30 June 1980 COMMERCIAL ITEM DESCRIPTION BEARING, BALL, THRUST: INCH AND METRIC SIZES, GROOVED RACE SURFACE RIGID OR FLAT SEAT TYPE The General Services Administration has authorized the use of this comme

2、rcial item description (CID), for all federal agencies. 1. SCOPE. This CID covers the requirements for a thrust ball bearing, referred to herein as “bearing“. It consists of two hardened and ground washers (thrust plates) that enclose a complement of precision ground and lapped balls and separated b

3、y a cage or retainer. The bearing is hsed to provide axial rigidity and not recommended if radial loading is expected. 2. SALIENT CHARACTERISTICS. 2.1 Materials. Unless otherwise specified herein or in the applicable engineering drawing (AED), the materials used shall be in accordance with the manuf

4、acturers material specifications/drawings. The use of recovered material made in compliance with regulatory requirements is acceptable providing all requirements of this CID are met (see 5.4). 2.1.1 Thrust plates and balls. The material for thrust plates and balls shall be vacuum degassed bearing qu

5、ality steel. 2.1.2 Heat treatment. The bearing shall be through hardened to Rockwell C-58 to C-66. Beneficial comments, recommendations, additions, deletions clarifications, etc. and any other data which may improve this document should be sent by letter to: U.S. Army Tank-Automotive Command, ATTN:

6、AMSTA-GDS, Warren, MI 48397-5000. L I AMSC NIA FSC 3110 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52491 W 9999974 OLb4258 bL3 W A-A-52 49 1 2.2 Design and con

7、struction. The general design and construction features of the bearing shall be dimensions shall as shown in figure 1. Detailed and specific features and be as specified in the AED. OUTSIDE DIAMETER (8) FIGURE 1. Thrust ball bearing. 2.2.1 Size. The size of the bearing and tolerances shall be determ

8、ined based on specific application requirements and as specified in the bearing AED (see 5.1). Factors such as load, rpm, environmental conditions (e.g., temperature, humidity) are taken into consideration. The basic empirical formula for bearing load is explained in 5.3. 2.2.1.1 Preferred sizes. Pr

9、eference shall be given to the sizes listed in table I before preparing an AED (see 5.2). 2.2.2 Radius or chamfer. Bearings must clear the maximum fillet radius of mating shaft or housing. A radius or chamfer (see figure l), .O31 inch minimum, shall be used on the bore or outer diameter. 2.2.3 Surfa

10、ces. Surfaces marked J in figure 1 shall represent maximum surface roughness in microinch. The ground surfaces shall be free from tool marks, chatter waves, pits, rust, or other injurious defects. Other surfaces shall have a smooth finish, free from scale. The bearings shall be supplied without lubr

11、ication, but with a coating of rust preventing film. 2.3 Identification markings. Identification markings shall be in accordance with the AED. Marking shall be permanent and legible and shall include, as a minimum, the AED part number and manufacturers CAGE code and part number. conforming to table

12、I the designated part or identification number (PIN) shall be used (see table I and 5.2). 3. QUALITY ASSURANCE PROVISIONS. 3.1 Responsibility for inspection. The contractor is responsible for the performance of all inspections (examinations and tests). - For bearings 2 Provided by IHSNot for ResaleN

13、o reproduction or networking permitted without license from IHS-,-,-A-A-52491 9999974 0164259 55T A-A-52 49 1 3.2 Contractor certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this commercial item description

14、 and that the product conforms to the producers own drawings, specifications, workmanship standards, and quality assurance practices. Items with known defects shall not be submitted for Government acceptance. The Government reserves the right to require proof of such conformance prior to the first d

15、elivery and thereafter as may be otherwise provided for under the provisions of the contract. 4. PRESERVATION, PACKAGING, PACKING, LABELING, AND MARKING. Preservation, packaging, packing, labeling, and marking for the desired level shall be as specified in the contract (see note 5.1). 5. NOTES. (Thi

16、s section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 5.1 Ordering data. Acquisition documents must specify the following: 1. Title, number, and date of this CID or AED, as applicable. 2. PIN or AED part number and quantity required. 3. Selecti

17、on of applicable level and paqkaging requirements. 5.2 Cross-reference data. For bearing sizes that previously conformed to MS17161C, the preparation of an AED is not required. Refer to table I for cross-reference of former MS part numbers to CID PIN numbers. 5.3 Bearing load formula. The equivalent

18、 thrust load rating (in pounds) for any combination of rotational speed (in rpm) and rating life (in hours) may be found from the following formula: P= 1ooc A (60 “)i3 1. 2. 3. 4 Where PA = Equivalent Thrust Load Rating C = Basic Dynamic Load Rating (Pounds) N = Rotational Speed - (rpm) H = Rating L

19、ife - (Hours) Equivalent thrust load is defined as that constant, central, purely axial load which, if applied to a bearing with rotating shaft washer and stationary housing washer, would give the same life as that which the bearing will attain under the actual conditions of load and rotation. Ratin

20、g life is defined as the number of hours at some constant speed that 90% of a group of apparently identical bearings will complete or exceed before the first evidence of fatigue develops. Basic dynamic load rating is defined as that constant, central, thrust load which a group of apparently identica

21、l bearings can endure for a rating life of one million revolutions of one of the bearing washers. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52491 = 4 0364260 271 D m L al n 3 n C nd P u w O e o C e CI O c rn -4 e Y( e LI al A-A-52491 Li. er

22、n ooooooo ?6666666 A-A-52491 SaNnOd S3NI;L CMO I4 o +I E-c m Li al n 5 E E c a u O al u C al Li al Cu al Li I u Li u W c m w 8 m m 2 .rl CI al Li Li al -4 P al Lc Id al u C m Li al O I3 ? rl m rl w H O 2 I d H n 3 VJ X u z H 9 Provided by IHSNot for ResaleNo reproduction or networking permitted with

23、out license from IHS-,-,-A- A-52 4L 9999974 0364266 T D A-A- 5 2 4 9 1 5.4 Regulatory requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. MILITARY INTERESTS: Custodians : Army - AT, Air Force - 99 Review activities: Army - MI Air Force - 84 DLA - IS User activities: Army - AR Navy - MC CIVIL AGENCY COORDINATING ACTIVITY: GSA-FSS PREPARING ACTIVITY Army - AT (Project 3110-0902) 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-