ARMY A-A-52205-1996 TABLE FOLDING LEGS《折叠桌》.pdf

《ARMY A-A-52205-1996 TABLE FOLDING LEGS《折叠桌》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-52205-1996 TABLE FOLDING LEGS《折叠桌》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、8 c f I INCH-POUND I A-A-52205 Julv 11. 1996 SUPERSEDING 5 September 199 1 MIL-T-3338H COMMERCIAL ITEM DESCRIPTION TABLE, FOLDING LEGS The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE 1.1 Scope. This commercial item des

2、cription (CID) covers a table with folding legs for use as a utility table in the field. 2. SALIENT CHARACTERISTICS 2.1 Design and construction. The table covered by this CID shall have comer legs which can be folded flat against the underside of the table for storage and transportation. All exposed

3、 surfaces of comers and edges shall be rounded. The table top shall be smooth with no visible protrusion. 2.2 Dimensions. The table shall measure 24 inches wide, 35 to 40 inches long and 26% to 28% inches high in its upright position. 2.3 Materials. The materials used shall be able to withstand extr

4、eme temperatures of -25F to 120F and not exhibit any evidence of corrosion when exposed to a field environment. ? Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, U.S. Army Natick Rese

5、arch, Development, and Engineering Center, Natick, MA O1 760-501 8 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 7105 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

6、 IHS-,-,-A-A-52205 Y999974 0171431 469 A-A-52205 2.4 Load capacity. The table shall support a weight of 80 pounds in its fully opened position distributed over an area measurement 18 inches by 1 8 inches in the center of the table top. 2.5 Surface finishing. 2.5.1 Preparation. Surfaces to be painted

7、 shall be free of burrs, slivers, cracks, scale, rough or sharp edges and foreign matter. They shall be cleaned, conditioned and primed, as appropriate, prior to painting. 2.5.2 Painting. All exterior surfaces of the table shall be painted green (see 6.4). The paint utilized shall not contain lead o

8、r chromate. Painted surfaces shall be continuous, smooth and adherent, without runs, drops, streaks, pin holes, cheeks, cracks or voids. The coating shall be free from imbedded foreign matter and shall not reveal peeling, flaking or blistering. 2.6 m. The legs shall have positive acting locking devi

9、ces when the table is fully opened and fully closed. Leg bottoms shall be equipped with closures (leg tips) for floor protection. 2.7 Drop test. A folded table shall be capable of being dropped on each corner from a height of two feet onto a smooth hard surface without structural damage, cracking or

10、 denting. 2.8 Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within the tolerances specified using conversion tables contained in the latest revision of ASTM E 380, and all other requ

11、irements of this document are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of

12、accepting or rejecting the product. 3. REGULATORY REQUIREMENTS 3.1 Contractor-recovered materials. The offerorlcontractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. QUALITY ASSURANCE

13、PROVISIONS 4.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description, shall conform to the producers own drawings, specifications, I 4 1 I t 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

14、-,-,-, 3 A-A-52205 standards and quality assurance practices, and be the same product that has been sold in the commercial marketplace for over one year, or is the same product that has successfully been delivered to the Government on a previous contract or purchase order. The Government reserves th

15、e right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. The following market acceptability criteria are necessary to document the quality of the product to be provided under this CID. a. The company pr

16、oducing the item must have been producing a product meeting the requirements of this CID for at least 2 years. b. The company must have sold 500 items meeting this CID, in the commercial or government marketplace over the past 2 years. 5. PACKAGING 5.1 Packaging. Preservation, packing and marking sh

17、all be as specified in the contract or purchase order (see 6.1). 6. NOTES 6.1 Ordering data. Acquisition documents must speciQ the following: a. Title, number and date of this document. b. Packaging requirements (see 5.1). 6.2 Sources for non-government association documents: ASTM STANDARD E 380 - U

18、se of the International System of Units (SI) (The Modernized Metric System) (Application for copies of ASTM standards should be addressed to the American Society for Testing and Materials, 1 O0 Barr Harbor Drive, West Conshohocken, PA 19428). 6.3 Sources of SUDDIV. Manufacturers whose products are k

19、nown to meet the requirements of this document are listed below; however, competition is not limited to these companies. Correll, Inc. 500 Moore Street Charleston, AR 72933 Mity-Lite 1301 W 400 N Orem, UT 94057 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

20、om IHS-,-,-A-A-52205 = 9999974 0171433 231 = A-A-52205 6.4 Table paint color. Past experience has shown that tables painted green conforming to color No. 24084 of FED-STD-595 were found to be acceptable. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY Custodian : Army - GL Air Force - 99 Review Activities GSA-FSS Preparing activity: Army - GL Project 7 105-0279 Army - CE1 Navy - MC Air Force - 84 DLA - GS c 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-