ARMY A-A-52055-1989 GLOVES MEN'S AND WOMEN'S LEATHER LIGHT DUTY《轻型皮革男女手套》.pdf

《ARMY A-A-52055-1989 GLOVES MEN'S AND WOMEN'S LEATHER LIGHT DUTY《轻型皮革男女手套》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-52055-1989 GLOVES MEN'S AND WOMEN'S LEATHER LIGHT DUTY《轻型皮革男女手套》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-52055 December 5, 1989 CokpiERcIAL ITEM DESCRIPTION GLOVES, MENS AND WCMENS, LEATHER, LIW DUTY The General Services Aministration has authorized the use of this cannercial item description. 1 . CLASSIFICATION 1.1 Classification. This carniercial itan description covers gloves in the following si

2、zes as specified (see 5.2). Schedule of sizes 1 2 3 4 5 2. SALIENT -ISTICS 2.1 Description. 2000 or equal. with a buckle strap closure on the back of the wrist an a snaphook and Wring system at the gauntlet for attaching the gloves to each other. The gloves shall conform to Rinehart Glove Ltd. style

3、 Flexor The gloves shall be unlined leather, wing th-, inseam sewn, I Beneficial carnients, recamiendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to: Carniander, U.S. Amy Natick Research, Developnent, and Engineering Center, ATIN: STR

4、NC-ESC, Natick, MA 01760-5014, AMSC N/A Fsc 8415 DISTRBTION STA- A. AppIoved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52055 2,2 Pattern parts. superimposed four-pointed star-shaped pattern pie

5、ces where each point canprises a finger part. Each finger portion pattern piece shall have an inner cutout of substantially rectangular shape. The pieces shall be joined together around their outer peripheries such that one pattern piece forms the palm side of the finger portion and the other patter

6、n piece forms the back side of the finger portion. parts than the pattern piece canprising the palm side before the pieces are joined together around their outer peripheries. The finger parts of the pattern piece canprising the back side shall be shortened by folding a part thereof upon itself to fo

7、rm a tuck which extends across the width of each finger part an so that the length of each finger part will be made substantially equal in length to each corresponding finger part of the pattern piece forming the palm side. The tucks shall be located at the first inter-phalangeal joints of the finge

8、r. The thumb piece shall be tucked in the same manner as the fingers. The widths of the finger parts corresponding to the finger portions of the two pattern pieces shall be equal such that when the pieces are joined at their peripheries, the junction between the pattern pieces will extend along the

9、line of non-extension for each finger, i.e., at the neutral axis extending along the length of each finger, such that the seam will not canpress or stretch upon flexing of the finger, The seam on the back of the glove which joins the back of the fingers to the back of the hand shall have an inserted

10、 welt, 3/16 to 1/4 inch wide. The welt shall not be caught in the closing seam. The seam on the palm side of the glove which joins the palm side of the finger to the palm side of the hard shall be covered with a palm patch of leather which extends approximately fram below the fingers to the thmb cro

11、tch and to the sean on each side of the hand. The glove shall extend approximately 2 inches beyond the wrist an the gauntlet shall be hemed. The gloves shall be available in five incremental sizes to fit the 5th percentile female through the 95th percentile male in the population. The finger portion

12、 of the glove shall be capri any variation in size, color, appearance, or finish in gloves of a pair; any ccarqxnent full, tight, or twisted; open seam; any hole, needle chew, cut or tear, or any spot or stain clearly noticeable; any unhealed scratch, grub, tick marks, open veins, scars or abraded a

13、reas, or clearly noticeable fat wrinkles in leather canponents; not soft ruid pliable; tucks not as specified; not properlymated. The lot size shall be expressed in units of one glove. one glove, and the selection shall be by pairs. II, and the acceptable quality level (AQL) , expressed in tem of de

14、fects per hundred units, shall be 6.5. The sample unit shall be The inspection level shall be 3.4 End item dimensional examination. The gloves shall be examined for conformance to the thickness of finished glove leather in 2.3.1, and the finished glove measuraaents specified in the contract or -chas

15、e order. Any dimension not within the specified tolerance shall be classified as a defect. The lot: size shall be expressed in units of one glove. The sample unit shall be one glove an the selection shall be by pairs. The inspection level shall be 5-3, and the AQL, expressed in terms of defects per

16、hundred units, shall be 4.0. NOTE: Each leather part of the glove shall be checked for thickness (i.e., thumb, body of glove, fingers and welts where feasible. parts that are not within the required thickness range shall constitute a defect. Measurements shall be taken with a Spring-Srpe graduated g

17、age with a flat pressure foot an flat anvil. Any of these 4. PACKAGING 4.1 Packaging. Wring and snaphook, shall be neatly stacked in a bundle, witheevery other pair reversed end for end, and securely tied at each end with cotton tape or twine to form a unit pack. 4.2 Packi grade 275 of PPP-B-636. Fi

18、ve pairs of gloves of one size, each pair attached by the Ninety pairs of gloves of one size only shall be packed in a fiber e rd box conforming to RCGL, type CF (variety SW) or SF, class d-tic, 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5

19、2055 4 = 777777q 00123b7 3 = A-A-52055 4.3 Palletization. When specified (see 5.2), gloves packed as specified shall be palletized in accordance with load type Ia of MIGSTP.147. 4.4 Marking. purchase order, bundles, shipping containers, and palletized unit loads shall be marked in accordance with MI

20、L-CTD-129. In addition to any special marking required by the contract or 5. NOTES 5.1 Intended use. protection. conditions, may be worn with the wool inserts covered by MI-835. are also intended for wear over chemical protective hadwear covered by MI-3976 . The gloves are intended for light work du

21、ty and mosquito They may be worn alone, or for additional warmth under cold The gloves 5.2 Ordering data. Acquisition documents must specify the following: a. Title, number, and date of this document b. Size required (see 1.1) C. men palletization is required (see 4.3) 5.3 Source for Governnent docu

22、ments. are available fran: Copies of Military and Federal documents Naval Publications and Forms Center AT“: NPDS 5801 Tabor Avenue Philadelphia, PA 19120-5099 5.4 Source for non-Goverrment documents. Copies of the AATaC Chranatic Transference Scale are available fram: mrican Association of Textile

23、Chemists and Colorists P.O. Box 12215 Research Triangle Park, Nc 27709-2215 5.5 Patent notice. described in this Carmercial Item Description. royalty-free license for this patent. 5.6 Water resistant treatment. co-application of an dsified fluorocarbon and a modified melamine hydrophobe type of resi

24、stant. Approval of such ccmponents and ccmbinations is the responsibility of the U.S. arimy Natick Research, Development, and Engineering Center, Natick, MA 0176&5014, and is based on more extensive tests, including those for toxicity, which are not set forth in.this document. Because of the time ne

25、cessary to conduct full evaluation (approximately 6 months) , only those chmnical treatments already approved and so listed in the invitation for bids or request for proposal shall be considered acceptable for the related procurement. U.S. Patent number 4654896 covers the design of the item as The G

26、overnnent does not have a The water resistant treatment consists of the 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52055 MILITAIRY INTERESTS: custodians &view Activities User Activities Navy -MC Air Force - 45 CIVIL AQXY OINATING XTMTY: GSA - FSS PREPARING ACPMTY: -a (Project 84154755) 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-