ANSI Z124.4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdf

《ANSI Z124.4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdf》由会员分享，可在线阅读，更多相关《ANSI Z124.4-2006 American National Standard for Plastic Water Closet Bowls and Tanks《塑料抽水马桶和水箱用美国国家标准》.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、ANSIZ124.4 - 2006Revision ofANSI Z124.4 - 1996American National Standardfor Plastic Water Closet Bowls and TanksSecretariatInternational Association ofPlumbing and Mechanical OfficialsApproved May 16, 2006American National Standards Institute, Inc.Licensed to Sarah Zhou. ANSI order X_63851. Download

2、ed 5/30/2008 4:21 AM. Single user license only. Copying and networking prohibited.Approval of an American National Standard requires verification by ANSI that therequirements for due process, consensus, and other criteria for approval have been met bythe standards developer.Consensus is established

3、when, in the judgement of the ANSI Board of Standards Review,substantial agreement has been reached by directly and materially affected interests.Substantial agreement means much more than a simple majority, but not necessarily una-nimity. Consensus requires that all views and objections be consider

4、ed, and that a con-certed effort be made toward their resolution.The use of American National Standards is completely voluntary; their existence does notin any respect preclude anyone, whether he has approved the standards or not, from man-ufacturing, marketing, purchasing, or using products, proces

5、ses, or procedures not con-forming to the standards.The American National Standards Institute does not develop standards and will in no cir-cumstances give an interpretation of any American National Standard. Moreover, no per-son shall have the right or authority to issue an interpretation of an Ame

6、rican NationalStandard in the name of the American National Standards Institute. Requests for inter-pretations should be addressed to the secretariat or sponsor whose name appears on thetitle page of this standard.CAUTION NOTICE: This American National Standard may be revised or withdrawn atany time

7、. The procedures of the American National Standards Institute require that actionbe taken periodically to reaffirm, revise, or withdraw this standard. Purchasers ofAmerican National Standards may receive current information on all standards by callingor writing the American National Standards Instit

8、ute.Published byInternational Association of Plumbing and Mechanical Officials5001 East Philadelphia Street, Ontario, CA 91761Copyright 2006 by International Association of Plumbing and Mechanical OfficialsAll rights reserved.No part of this publication may be reproduced in anyform, in an electronic

9、 retrieval system or otherwise,without prior written permission of the publisher.Printed in the United States of AmericaAmericanNationalStandardLicensed to Sarah Zhou. ANSI order X_63851. Downloaded 5/30/2008 4:21 AM. Single user license only. Copying and networking prohibited.ContentsPageForeword i

10、ii1 Scope and Purpose.11.1 Scope .11.2 Purpose 11.3 Normative References .12 General Requirements .12.1 Materials 12.2 Dimensional Requirements .12.3 Selection of Units for Testing .12.4 Installation Instructions .12.5 Care and Maintenance Instructions.12.6 Identification22.7 Concealed Tanks .22.8 S

11、pud Sizes .22.9 Handicap/Physically Challenged Installations 22.10 Closet Seats .22.11 Sanitary and Hydraulic Performance of Water Closet Tanks and Bowls.23 Workmanship and Finish.23.1 Unit Preparation 23.2 Method of Inspection of the Unit Surface.23.3 Surface Characteristics 23.4 Subsurface Porosit

12、y.24 Structural Integrity of Complete Units34.1 Radii Load Test .34.2 Closet Auger Effect (Trapway).34.3 Load Tests .34.3.1 Unit Preparation.34.4 Fixture Connection Loads .44.4.1 Bowl Connections44.4.2 Tank Connections 44.4.3 One Piece Water Closets .44.5 Static Loads .54.5.1 Bowl Rim Load54.5.2 Tra

13、pway Leak Resistance54.5.3 Tank Top Load 54.5.4 Hydrostatic Load54.6 Torque Loads.64.7 Impact 65. Physical Characteristics of Materials 65.1 Colorfastness .65.2 Resistance to Staining .65.3 Wear and Cleanability.75.4 Cigarette Test 95.5 Chemical Resistance95.6 Water Absorption 95.7 Water Resistance

14、.95.8 Warpage.10iLicensed to Sarah Zhou. ANSI order X_63851. Downloaded 5/30/2008 4:21 AM. Single user license only. Copying and networking prohibited.Page6. Common Fixture Types and Sizes 106.1 General 107 Provisions for Government Procurement 10Tables1 Surface Appearance Requirements32 Allowable D

15、eflections .63 Impact Locations .64 Reagents Used in Stain Resistance Test75 Brush Schedule 86 Reagents Used in Chemical Test.9Figures1 Bowl Inlet Connection Test.112 Bowl Outlet Connection Test 113 Seat Mounting Test124 Tank Inlet Connection Test .125 Bowl Rim Load Test .136 Trapway Leak Resistance

16、 Test137 Location of Loading Points on Tank Cover138 Hydrostatic Load Test .149 Apparatus and Location of Impact Points.1410 Boil Test Tank (Top View of Tank Without Screws).1511 Boil Test Tank .1612 Brush Holder (Z124 Wear Test)1713 Platform 7.0% ethoxylated-alkyl-phenol(Monsanto Sterox NJ or Rohm

17、8.0% sodium-xylensulfonate (Stepan Chem. Co., Stepan SXS was used); 1.5% butyl cellosolve(2-butoxy ethanol); 75.5% water.3To hasten drying, surfaces shall be permitted to be wiped with a clean chamoisleather or a clean absorbent, lint-free material (for this test only).4Standard dirt consists of: 20

18、 parts carbon black (pigment grade), 20 parts ironblack (iron oxide, black), 20 parts calcium sterate, 5 parts 30W motor oil, 1 partwetting agent (Triton X-100, Rohm then rotated to two other positions. The weightshall be left suspended at each of these positions for 2 1/2minutes each. (NOTE: The tw

19、o positions shall be approxi-mately 180 degrees apart.) The tank shall be inspected forvisible damage while the load is in place. The load shall beremoved, and after inking as described in 3.3.1, shall beinspected for damage by the procedure specified in 3.2.4.4.2.1.2 Performance requirement. There

20、shall beno visible cracks or water leakage either when the load is inplace or after removal of the load, nor any visible distortionafter removal of the load.4.4.2.2 Tank front, bolt and outlet connection4.4.2.2.1 Test method. The tank shall be mounted tothe bowl as described in 4.3 with torque of 5.

21、4 .5 Nm (48 5 in. lbs.) to each threaded fastener. The water supply lineshall be connected to the water inlet shank. A static pressureof 515 35 kPa (75 5 psi) shall be maintained. The waterlevel in the tank, complete with cover, shall be adjusted tothe manufacturers recommended highest level. The se

22、atcover shall be in the open position. A horizontal force shallbe gradually applied through the seat cover centrally locatedat the highest level of contact between seat cover and thewater closet or tank cover so a force of 445 20 N (100 5lbs.) shall be created. The tank cover shall remain in placedu

23、ring loading. With the load in place, the unit shall beflushed five (5) times and the tank connections shall beobserved for any visible damage or water leakage. The loadshall be removed. After 24 hours, the load shall be reappliedand the unit shall be flushed five additional times. The tankconnectio

24、ns shall be observed for any visible damage orwater leakage. The water supply shall be disconnected andthe tank shall be emptied. The surface shall be inked, asdescribed in 3.3.1, and shall be inspected for damage by theprocedure specified in 3.2.4.4.2.2.2 Performance requirement. There shall novisi

25、ble cracks nor water leakage either when the load is inplace or after removal of the load, nor any visible distortionafter removal of the load. The tank shall not become dis-lodged during the test.IAPMO/ANSI Z124.4-20064Licensed to Sarah Zhou. ANSI order X_63851. Downloaded 5/30/2008 4:21 AM. Single

26、 user license only. Copying and networking prohibited.4.4.3 One piece water closets4.4.3.1 Outlet connection, seat mounting tests andinlet connection. Bowl connection test 4.4.1.2, seat mount-ing test, 4.4.1.3 and tank inlet connection test 4.4.2.1 shall beperformed.4.5 Static loads4.5.1 Bowl rim lo

27、ad4.5.1.1 Test method. Two steel channels, 75 mm (3in.) in depth and approximately 610 mm (2 ft.) long, back toback and spaced 75 mm (3 in.) apart shall be used. A 6 mm(1/4 in.) steel plate of convenient size shall be welded to thetop flanges of the channels. The channels shall be placedacross the b

28、owl rim and shall be centered at a distance of 254mm (10 in.) for regular and 305 mm (12 in.) for elongatedbowls measured normal to the centerline across the seat boltholes. (See Figure 5) Rubber discs, approximately 32 x10mm (1-1/4” x 3/8”) shall be placed at four positions noted inFigure 5, to sim

29、ulate bumpers, between the channels andrim. The bowl shall be filled to the normal level with waterprior to the application of the load. A load of 1334 22 N(300 5 lbs.) including the weight of channels and plateshall be placed on the fixture. Deflection of the rim shall bemeasured after 60 5 minutes

30、 with the load in place, andafter an additional 60 5 minutes with the load removed.Rim deflection shall be measured at points indicated inFigure 5 with an instrument having a accuracy of 0.025 mm(0.001”). The bowl shall be inspected for visible damagewhile the load is in place. The load shall be rem

31、oved and thesurface shall be inked as described in 3.3.1, and shall beinspected for damage by the procedure specified in 3.2.4.5.1.2 Performance requirement. There shall be novisible cracks or water leakage either when the load is inplace or after removal of the load, nor any visible distortionafter

32、 removal of the load. Rim deflection with load in placeshall not exceed 2.54 mm (0.10 in.) after 60 5 minutes.Residual deflection 50 5 minutes after load removal shallnot exceed 1.3 mm (0.05 in.).4.5.2 Trapway leak resistance.4.5.2.1 Test method. The trap shall be filled to the nor-mal level and the

33、 trapway outlet shall be sealed with a suit-able rubber plug. The dry portion of the trapway be subject-ed to an air pressure of 0.5 kPa (2 in.) of water column for aperiod of 15 1/2 minutes using a gauge with a range notexceeding 127 mm (5 in.) water column or a water manome-ter with graduations no

34、t exceeding 3 mm (1/8 in.) water col-umn (see Figure 6). If a decrease in gauge reading isobserved after 15 minutes, the pressure shall be maintainedfor an additional 15 1/2 minutes, at which time the gaugeshall again be observed. This test shall be made subsequentto the Auger Test (4.2) and the Rim

35、 Load test (4.5.1.).4.5.2.2 Performance requirement. There shall be noleakage during exposure to the test pressure for 15 1/2minutes, as indicated by the pressure gauge. If a smalldecrease in gauge reading is observed after 15 1/2 minutes(that might be due to temperature effects), a second gaugeread

36、ing shall be made after a total of 30 1 minutes of expo-sure. There shall be no additional decrease.4.5.3 Tank top load4.5.3.1 Test method. The tank shall be mounted withcover on a matching bowl or suitable test fixture. A load of445 22 N (100 5 lbs.) shall be applied to the top of theinstalled cove

37、r of the unit along the lengthwise centerline ateach of two separate places: (1) at the midpoint of the topand (2) at the quarter point from one end. The load shall beapplied on a 75 mm (3 in.) diameter steel weight distributiondisc resting on a 13 mm (1/2 in.) thickness of sponge rubberor other sui

38、table soft material which is in contact with theunit surface being loaded, as shown in Figure 7. The loadshall remain in place 2 1/2 minutes. The tank shall beobserved for visible damage while the load is in place. Theload shall be removed, and shall be inked as described in3.3.1, and inspected for

39、damage by the procedure specifiedin 3.2.4.5.3.2 Performance requirement. There shall be novisible cracks or water leakage either when the load is inplace or after removal of the load, nor any visible distortionafter removal of the load.4.5.4 Hydrostatic load4.5.4.1 Test method. The tank shall be mou

40、nted withcover on a matching bowl or suitable test fixture.Measurements of tank deflection shall be made at severallocations. These measurements shall be conducted separate-ly or collectively. Dial indicators as specified below shall beused. The tank shall be filled with water to the manufactur-ers

41、recommended highest level, with water maintained at 23 3 C (75 5 F). The sum of the two deflections observedat each location shall be recorded. The tank shall be emp-tied.Position of dial indicators (see figure 8)(a) Ends of Tank. A dial indicator shall be positionedon the outside at each end of the

42、 tank, midway between thefront and back, at a position 13 mm (1/2 in.) below the man-ufacturers specified waterline.(b) Front and Back of Tank. A dial indicator shall bepositioned on the outside of both front and back walls of thetank, midway between the ends and at a position 13 mm (1/2in.) below t

43、he manufacturers specified water line.(c) Bottom of Tank. Where possible, a dial indicatorshall be positioned on the outside bottom of the tank at eachof the two quarter points nearest the ends and midwaybetween the front and the back walls of the tank. If ribs arelocated at or near these points, th

44、e dial indicators shall bemoved to a position midway between the ends of the tankand the ribs.4.5.4.2 Performance requirement. Maximum deflec-tion shall be in accordance with Table 2. Neither of the twodeflections taken at each position shall exceed 75% of thetotal allowed.IAPMO/ANSI Z124.4-20065Lic

45、ensed to Sarah Zhou. ANSI order X_63851. Downloaded 5/30/2008 4:21 AM. Single user license only. Copying and networking prohibited.Table 2 - Allowable deflectionsLocation SumEnd deflection, mm (inch) 1.5 mm (0.060)Front and back deflection, mm (inch) 4.6 mm (0.180)Bottom deflection, mm (inch) 1.0 mm

46、 (0.040)4.6 Torque loads4.6.1 Flange connection4.6.1.1 Test method. The bowl shall be mounted asspecified in 4.3. The nuts shall be torqued to 2.71 0.2 Nm(24 2 in. lbs.) and shall be retorqued after 24 hours. Wallmounted water closets shall be installed in accordance withthe carrier manufacturers in

47、structions. The load shall beremoved after a total of 48 hours. The flange connectionshall be inked using the same solution and techniquedescribed in 3.3.1, the flange shall be visually inspected forpermanent distortion and cracks as specified in 3.2.4.6.1.2 Performance requirements. There shall be

48、novisible cracks, surface distortion, or other damage when theload is in place and after removal of the load.4.7 Impact4.7.1 Test method. A 38 mm (1-1/2 in.) diameter,0.225 kg (1/2 lb.) steel ball shall be dropped one time perimpact point from the specified height to strike several dif-ferent points

49、 on the unit surfaces as specified in the Table 3and as shown in Figure 9. The ball shall be dropped inside aguide tube 42 mm (1-5/8 in.) inside diameter. The tube shallbe positioned vertically (within 5) of its longitudinal axisaligned with the specified point of impact within 3 mm (1/8in.). The ball shall be dropped from a position such that itslower periphery is at the same elevation as the top end of theguide tube. The guide tube shall be rigidly clamped so as toremain in the specified position during testing. The testsshall be mad