AIR FORCE MIL-S-5804 C (2)-1981 SEAT AIRCRAFT TROOP WALL-STYLE《部队壁式飞机座》.pdf

《AIR FORCE MIL-S-5804 C (2)-1981 SEAT AIRCRAFT TROOP WALL-STYLE《部队壁式飞机座》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-S-5804 C (2)-1981 SEAT AIRCRAFT TROOP WALL-STYLE《部队壁式飞机座》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-5804C AMENDMENT 2 3 AUG 81 SUPERSEDING AMENDMENT 1 15 Nov 1968 MILITARY SPEC IF ICATION SEAT, AIRCRAFT, TROOP, WALL-STYLE This amendment forms a part of Military Specification MIL-S-5804C, dated 16 August 1967, and is approved for use by all Departments and Agencies of the Department of Defens

2、e. Add to bottom of Page 1: 11 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: HQ AFLC CASO/LODS, Federal Center, Battle Creek, MI 49016 by using the self-addressed Standardization Document Propos

3、al (DD Form 1426)appearing at the end of this document or by letter.“ PAGE 1 * 2.1 SPECIFICATIONS * * - Federal Delete, QQ-P-416 Plating, Cadmium (Electro-Deposited) Mi 1 i tar y Delete, “MIL-D-1000 Drawings, Engineering and Associated List“ and substitute “DOD-D-1000 Drawing, Engineering and Associ

4、ated List“ PAGE 2 Under SPECIFICATION, Military: Aircraft Floor“ and substitute: “MIL-F-8 905 Delete “MIL-A-8905 Adapter, Tiedown Fittings And Cargo Rings, Tiedown, Aircraft Floor II Under STANDARDS, Military: Delete, MS26540 Plate-Anchor, Aircraft.Troop Seat .- FSC 1680 . . _., L c Provided by IHSN

5、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.- MIL-S-SBOVC (2) Lb 7997706 0385352 7 MIL-S-5804C Delete parenthetical source paragraph in its entirety and substitute the following: “(Copies of specifications, standards, drawings, and publications required by cont

6、ractors in connection with specific procurement func- tions should be obtained from the procuring activity or as directed by the contracting officer.)“ PAGE 3 Add the following new paragraph: “3.3.3 Reclaimed materials. The use of reclaimed materials shall be encour- aged to the maximum extent possi

7、ble.“ PAGE 4 3.4.2, Line 4: Delete “the stud of anchor plate shown in MS26504 and.“ Line 5: Delete “MIL-A-8905“ and substitute %IIL-F-8905 .I1 PAGE 10 3.6, Line 4: Delete “MIL-D-1000“ and substitute “DOD-D-1000.“ Delete 3.9 Finish and substitute: “3.9 Finish. Aluminum-Alloy parts shall be anodically

8、 treated in accordance with the MIL-A-8625, type II, undyed, and noncorrosion resistant steel parts shall be zinc plated in accordance with QQ-2-325, type II, class 2. Primer will be one coat of MIL-P-23377, top coat with two coats lacquer TT-L-20 color 36231.“ PAGE 12 4.4.1, Line 3: instead of ulti

9、mate loads.“ After “4.6.2“ add “except that the proof loads shall be used The margins of this amendment are marked with an asterisk to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the Governme

10、nt assumes no liability whatsoever for any inaccuracies in these notations, Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Custodian: Air Force - 99 Army - AV Preparing activity: Air Force - 99 Project No. 1680-F419 *U.S QOVERNMENT PRINTINO OFFICE: 1881 - 703623/6894 Page 2 of 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-