AIR FORCE MIL-P-87133 (2)-1988 PLOTTER COMBAT MISSION PLU-6 C (AIR NAVIGATION)《PLU-6 C型(空中导航)战斗任务绘图器》.pdf

《AIR FORCE MIL-P-87133 (2)-1988 PLOTTER COMBAT MISSION PLU-6 C (AIR NAVIGATION)《PLU-6 C型(空中导航)战斗任务绘图器》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-P-87133 (2)-1988 PLOTTER COMBAT MISSION PLU-6 C (AIR NAVIGATION)《PLU-6 C型(空中导航)战斗任务绘图器》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、I MILITARY SPECIFICATION NIL-P-7333 (2) bb 797770b 0345640 7 r* 4 MIL-P-87133(USAF) AMENDMENT 2 ,f - SUPERSEDING AMENDMENT 1 18 January 1983 - . PLOTTER COMBAT MISSION, PLU-/C (AIR NAVIGATION) This amendment forms a part of MIL-P-87133, dated 18 January 1983, and is approved for use within the Depar

2、tment of the Air Force and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 * 2.1 Delete “first sentence“ and add: “Government documents.“ - * “2.1.1 Specifications and standards. The following specifications and standards form a part of this specification to

3、 the extent specified herein. Unless otherwise specified, the issues of these documents.shal1 be those listed in the issue of the Department of Defense Index of Specifications, and Standards (DODISS) and supplement thereto, cited in the solicitation. * Under SPECIFICATION, FEDERAL, delete “PPP-F-320

4、“ and add: “PPP-B-601 Boxes, Wood, Cleated Plywood“. * Under SPECIFICATION, Military, delete “MIL-B-117“. * Under STANDARDS, Military, delete “MIL-STD-794“ and add: “MIL-STD-2073-1 DOD Material Procedures For Development And Applicable Of Packaging Requirements“. * Delete address on lines 3 and 4 of

5、 beneficial comments block and add: “Oklahoma City Air Logistics Center/MMEDO, Tinker AFB OK 73145-5990“. PAGE 2 * Add: “2.2 Other publications. The following document(s) form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which-a

6、re DOD adopted shall be those listid in the issue of the DODISS specified in the solicitation. of documents not listed in the DODISS shall be the issue of the nongovernment documents which is current on the date of the solicitation. Unless otherwise specified, the issues American Society For Testing

7、 And Materials (ASTM) ASTM D3951 Packaging, Commercial (Application for copies should be addressed to: ASTM, 1916 Race St Philadelphia PA 19103. ) AMSC N/A 1 of 4 FSC 6605 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction o

8、r networking permitted without license from IHS-,-,-MIL-P-87133 (2) 66 9777706 0195641 O W MIL-P -8 7 133 (USAF ) AMENDMENT 2 (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be ava

9、ilable in or through. libraries or other informational services)“. In the event .of a conflict between the text of- * Add:,“2.3 Order of precedence. this specification and the reference cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this

10、 specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained “ . * Delete “3.1“ and add new: “3.1 First article. When specified in the contract or purchase order, a sample shall be subjecte

11、d to first article inspection (see 4.3 and 6.2)“. 3.3.1 Delete and add: “3.3.1 Printing. The printing shall be on-the underside of the base to avoid parallax. and magenta j .k as specified on figures 1 and 2. and 2 conflict with the requirements of 3.3.1.1 through 3.3.1.5, the requirements of 3.3.1.

12、1 through 3.3.1.5 shall apply“. The printing shall be on clear plastic in black If the requirements of figures 1 PAGE 5 3.6 Delete in its entirety. * Add : “3.8 Recycled and reclaimed materials. Recycled and reclaimed materials shall be encouraged to the maximum extent possible without jeopardizing

13、the intended end use of the item“. PAGE 7 * Add: “4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any insp

14、ection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies sebmitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known de

15、fective material, either indicated or actual, nor does it commit the Government to acceptance of defective material“. * Delete “4.2(a)(b) in its entirety and add new:. “4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspect

16、ion (see 4.3). b. Quality conformance inspection (4.4)“. * Delete Section 5 in its entirety and add: “5. PACKAGING 2 A- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-8 7 133 (USAF ) AMENDMENT 2 5.1 Preservation. Preservation shall be level A,

17、 C, or Industrial, IAW MIL-STD-2073-1, as specified (see 6.2) 5.1.1 Level A. 5.i1.1.1 Cleaning. MIL-P -1 16 Plotter shall be cleaned in accordance with process C-1 or PAGE 9 5.1.1.2 Drying. MIL-P-116. Plotter shall be dried in accordance with process D-4 of 5.1.1.3 Preservation application. Preserva

18、tive shall not be used. 5.1.1.4 Unit packaging. Unless otherwise specified by the contracting activity, each plotter shall be packaged in quantity unit packs of one each in iccordance with Method III of MIL-P-116. Each plotter shall be placed in a PP 3-636 Fiberboard container weather resistant, wit

19、h sufficient cushioning I terial between bag and unit container of a type, density, and thickness to insure shock transmission does not exceed peak vslues in Gs established for the plotter when completed packs are subjected to the rough handling drop tests of MIL-P-116. 5.1.2 Level C. Each plotter s

20、hall be clean, dry, and individually packaged in a manner that will afford adequate protection against corrosion, deterioration, and physical damage during shipment from supply source to the first receiving activity. 5.1.3 Industrial. with ASTM D3951. The Industrial preservation of plotter shall be

21、in accordance 5.2 Packing. Packing shall be level A, B, C, or Industrial as specified (see 6.2). 5.2.1 Level A. Plotter packaged as specified in 5.1.1 shall be packed in shipping containers conforming to PPP-B-601, Styles A or B, Class overseas, unless otherwise specified by the contracting activity

22、. Insofar as practical, exterior shipping container shall be of uniform shape, size, minimum tare and cube consistent with the protection required. 5.2.2 Level B. containers conforming to PPP-B-636, class weather-resistant, unless otherwise specified by the contracting activity. Plotter packaged as

23、specified in 5.1.1 shall be packed in shipping I Other requirements as specified in 5.2.1 apply 5.2.3 Level C. domestic shipment from the supply source to the first receiving activity for immediate use. regulations. Packing shall be applied which affords adequate protection during This level shall c

24、onform to applicable carrier rules and 5.2.4 Industrial. D3951. The packaged plotter shall be packed in accordance with AS& 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-87L33 (2) bb m 777770b 0345643 4 m MIL-I?-87 133 (USAF ) AMENDMENT 2 5

25、.3 Marking. In addition to any other markings required by the contract or order (see 6.2), interior and exterior containers shall be marked in accordance with MIL-STD-129. “ PAGE 10 ._ 6.2(c) Delete in its entirety. The margins of this amendment are marked with an asterisk to indicate where-changes

26、(additions, modif icationc, corrections, deletions) from the previous amendment were made. whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and re

27、lationship to the last previous amendment. This was done as a convenience only and the Government assumes no liability Custodian: AIR FORCE .-99 Preparing activity: AIR FORCE -71 Project No 6 6 05 -F 3 8 9 ? - 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-