AIR FORCE MIL-K-83782 A-1978 KIT BAG FLYER'S《飞行员用工具袋》.pdf

《AIR FORCE MIL-K-83782 A-1978 KIT BAG FLYER'S《飞行员用工具袋》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-K-83782 A-1978 KIT BAG FLYER'S《飞行员用工具袋》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、cc 5rq (ao *MIL-K-8372A 84 997990b 0409269 I = MIL-K-83782A 18 ne-8 SUPERSEDING MIL-K-83782 12 October 1971 MILITARY SPECIFICATION KIT BAC, FLYERS This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 This specification covers one type and

2、size of clothing bag which is designated type BU-2/P. 2. APPLICABLE DOCUMENTS t 2.1 Issues of documents. “he following documents of the issue in effect on date of invitation for bida or request for proposal, form a part of the speci- fication to the extent specified herein. SPECIFICATIONS Federal v-

3、F-o V-T-295 UU-P-268 DDD-L-20 PPP-B-6 36 Fasteners, Slide, Interlocking Thread, Nylon Paper, Kraft, Wrapping Label; For Clothing, Equipage And Tentage, (General Use) Boxes , Shipping, Fiberboard Military MIL-B-371 MIL-W-4088 MIL-C-7 515 MIL-F-10 336 MIL-F-10 884 Braid, Textile, Tubular Webbing, Text

4、ile, Woven Nylon Cord, Nylon, Coreless Fiber, Sheet, Vulcanized Fasteners, Snap- I- Beneficial commente (recommendations, additions, deletions ) and any pertinent data which may be of use in improving this document should be addressed to: HQ AFLC CASO/MDS, Federal Center, Battle Creek MI 49016 by us

5、ing the self- addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. i THIS DOCUMENT CONTAINS ) PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Natural Or In Colors STANDARDS

6、Federal FED-STD-751 Stitch, Seam and Stitching Military MIL-STD-105 MIL-STD-129 DRAWINGS Sampling Procedures And Tables For Inspection By Attributes Marking For Shipment And Storage Air Force 5 9 36 72 59K367i 65B1539 65 B15 40 65B1541 Pouch-Shoe, Flyers Kit Bag, Assembly Of Kit Bag, Flyers Type BGU

7、-2/P Assembly Handle, Flyers Kit Bag, Assembly Of Stiffener-Flyers Kit Bag, Lower Stiffener-Flyers Kit Bag, Upper (Copies of specifications , standards, drawings, and publications required by suppliere in connection with specific procurement functions should be obtained from the procuring activity o

8、r as directed by the contracting officer.) 2.2 Other publ.ications. cation to the extent specified herein Unless otherwise indicated, the issue in effect on date of invitation for bids or reauest for proposal shall apply. The following documents form a part of this specifi- UNIFORM CLASSIFICATION CO

9、MMITTEE UNIFORM FREIGHT CLASSIFICATION RULES (Application for copies should be addressed to the Uniform Classification Committee, Room 202 Union Station, 516 W. Jackson Blvd., Chicago, Illinois 60606 ) NATIONAL CLASSIFICATION BOARD NATIONAL MOTOR FREIGHT CLASSIFICATION (Application for copies should

10、 be addressed to the National Classification Board, 1616 P Street, N.W., Washington DC 20036.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-K- 37

11、 82A 3,4,4.i Slide fastener tane, nylon filling dyed USAF color shade sage green No, 1509 to match standard sample, and shall be mildew resistant treated. The finished tape shall show good fatness to weathering. The slide fastener tape for the bag closure fastener shall have a width of 3/4 inch and

12、a 3/4 inch tape extension. slide fastener tape for the inner pocket fastener shall have a 7/16 inch width and a 3/4 inch extension. 34.4.2 E8fng (tab). The webbing tab for the slide fastener shall conform to MIL-W- O the basic material. The slide fastener tape shall be cotton warp and The type XII a

13、nd the color shall approximately match the color of * 3.4.4.3 Webbing (thongsL. The webbing thongs shall conform to MIL-T-43566, type I, class 3, and shall be 3/8 inch wide except that the overhand knot at free end6 of thong may be omitted. The finished length of the thong after assembly to the pull

14、 shall be 3 I1/8 inches. type VLI, class 2 of MIL-E-371 may be used, The color shall be USAF color ehade sage green No, 1509, 3,4,4.4 _9rawstri_ngmhmuch, The drawstring for the shoe pouch shall be nylon cord conforming to MIL-C-7515, type I. inches euad the approximate color of the basic fabric (ref

15、erence drawing As an alternate, cottonbraid, It shall be a cut length of 24 59D3672 ) 3,4,5 Handles, The handle shall conform to drawing 65B1539. 3.4.6 Fibe-rboard stiffeners , The fiberboard supports shall conform to drawings 65B130 and The stiffeners shall be cemented to the bag with a suitable ty

16、pe cement having an adhesive quality of 5 pounds par inch minimum when ry. 3.4.7 Identif( Contractors Name protective finish omitted or not a8 specified corners irregularly shaped Corners-radius not uniform on ail corners of pockets or n. Slide fasteners 1, 2. lot specified type or style Slider on b

17、ag closure or inner pocket fails to inter- lock chain; tape improperly applied, causing malfunction, or tape edges of slide fastener on bag closure notched to form a curved configuration 3. Thong omitted o. Handle-not fabricated as indicated on Drawing 65B1539 -Seriously affecting serviceability or

18、appearance -Affecting serviceability or appearance but not seriously 1, 2. 3. 4 Ends of stitching not knotted or backstitched Not attached to bag as specified on Drawing 59K3671 Any post and screw not securely attached Sealing compound omitted on any assembled post p. Stiffeners 1. 2. Cracked, warpe

19、d, delaminated or construction not Openings in upper stiffener covered by fabric, reversed or not covered by flap when flap is closed a8 specified -Seriously affecting serviceability -Affecting serviceability but not seriously -Burrs or sharp edges not removed 8 CLASSIFICATION MaJ or X X X X X X X X

20、 - Mi I A I X X X X X X X X X X X X X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NSL-K-3782A LJ 999970b 0407277 O MILK-83782A TABLE I, Classification of Material Defects (Contd) Defects 3. Not securely cemented to bag fabric 4. Cement tacky, or

21、cement extends beyond edges of stiffener by more than 1/4 inch 5. Upper stiffener not positioned as specified q. Shoe pockets 1. Drawstring omitted, cut or abraded 2. Ends of drawstring not finished as specified; less than specified length by more than 1 inch 3. Grommets at drawstring openings omitt

22、ed, or damaged affecting movement of serviceability of cord 4. Grommets clinched excessively tight cutting eurrounding fabric or insecurely clinched, i.e., gromet or washer become disengaged Either drawstring cord caught in hem stitching causing failure to draw freely Drawstring hem improperly forme

23、d , badly puckered, twisted, or pleated, or smaller than specified width by more than 1/4 inch r. Identification label 5. 6. 1, Omitted, misplaced, illegible, incorrect or size Reinforcements-omitted, misplaced, or improperly applied of characters not as specified s. failing to serve intended purpos

24、e -Finished dimensions of reinforcements less than specified -Slide fastener tape extension on pockets not caught by more than 1/8 inch, unless otherwise specified in stitching t. Snap fasteners-not specified type, size or finish -Any fastener not functioning properly, failing to snap -Female fasten

25、ers on body gusset do not correspond with closed or open freely; any fastener omitted male fasteners on shoe bag failing to effect a smooth attachment -Improperly set, not securely clinched, i.e, components of stud or socket separate when fasteners are snapped and unsnapped; clinched excessively, cu

26、tting surrounding fabric more on inside pocket -Snap fasteners set out of alignment by 1/4 inch or U. Cleanness Stains (oil, grease, ink, dirt, cement, et cetera) clearly noticeable; thread ends not trimmed throuhout ” 9 %ASSIF: Ka3 or X X x X X X tTION ii I 1 1 r L i K X X X X X I Provided by IHSNo

27、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-K-3782A 4 W 779770b 0409278 2 m MIL-K-83782A 4.3.2. Oime_nsi_onal,.exnnigoing,packinging An examination shall be made to determine that packaging, packing and marking comply with Section 5 requirements of this speci

28、fication, Defects shall be scored in accordance with the list below. The sample unit shall be one shipping container fully prepaxed for delivery shall be examined for defects of closure. the number of shipping containers in the end item inspection lot. The inspec- tion level shall be S-2 and the AQL

29、 shall be 2.5 defects per hundred units. The lot size shall be EXAMINE - DEFECT - Marking Omitted, incorrect , illegible; of improper size, location , sequence or method of application. Materials Any component missing or damaged, affecting serviceability Workmanship Inadequate application of compone

30、nts, such as incomplete closure of container flaps, loose strapping, or taping, inadequate stapling Content Bulged or distorted container. Number of bags per container is more or less than required. 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

31、NIL-K-83782A 4 = 999990b 0409279 4 5. PACKAGING MIL-K-83782A 5.1 Preservation-packaain& Packaging shall be level A or C as specified. (see Z.2) 5.1.1 Level A. Each kit bag, &th all fastenings secured, shall be neatly folded to measure 26 by 20 inches. 5.1.2 Level C. Kit bags shall be packaged to aff

32、ord adequate protection against deterioration and physical damage during shipment from the supply source to the first receiving activity. practice when it meets these requirements. 5.2 Packinq. Packing shall be level A, B, or C as epecified. (See 6.2) Te supplier may use his standard 5.2.1 m. Twenty

33、 kit bags, packaged as specified, shall be packed in a snug-fitting fiberboard shipping container, conforming to type SF, class weather-resistant grade V2S, style FOL-L of pPP-636 Each shipping container shall be fitted with a box liner fabricated of type CF, grade V3c of PPP-636. The contents shall

34、 be completely covered on top and bottom with a piece of 30 pound minimum basis weight kraft paper conforming to grade B of UU-P-268. “he container shall be closed, waterproofed, and reinforced in conformance with the requirements of the appendix of the box specification. 5.2.2 Level B. Twenty kit b

35、ags, packaged as specified, shall be packed in a snug-fitting fiberboard shipping container conforming to CF or SF, class domestic, grade 275, style FOL-L of P-13436. Each shipping container shall be fitted Kith a box liner fabricated of type CF, class domestic, variety DW, grade 275 of PPP-B-636. b

36、ottom with a piece of 30 pound minimum basic weight kraft paper conforming grade B of uu-P-268. The container shall be closed in conformance with the requirements of the appendix of the box specification. The contents shall be completely covered on top and 5.2.3 Level C. that Will afford adequate pr

37、otection against physical damage during shipment from the supply source to the first receiving activity. conform to Uniform Freight Classification or National Motor Freight Classifi- cation Rules and Regulations as applicable. Kit bags packaged as specified shall be packed in a manner Containers sha

38、ll 5.3 &-. order, shipping containers shall be marked in conformance with the require- ments of MIL-STD-129. In addition to any special marking required by contract or 6. NOTES 6.1 Intended use. personnel to carry items of peronal property while traveling. Tbe kit bag is to be used by flight crews a

39、nd other a. b. c. Title, number and date of this specification. When a first article is requried (see 3.1). Selection of applicable levels of packaging and packing (see 5.1 and 5.2) 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-