AIR FORCE MIL-C-3095 G-1988 CAP SERVICE MAN'S AIR FORCE《空军男式服役制服帽》.pdf
《AIR FORCE MIL-C-3095 G-1988 CAP SERVICE MAN'S AIR FORCE《空军男式服役制服帽》.pdf》由会员分享,可在线阅读,更多相关《AIR FORCE MIL-C-3095 G-1988 CAP SERVICE MAN'S AIR FORCE《空军男式服役制服帽》.pdf(43页珍藏版)》请在麦多课文档分享上搜索。
1、i l L L k !- i I I I b a i I f t L I , I L i I i r Beneficial connnents (recomnendations, additions, deletions) and any pertinent data vuhich may be of use in improving this document should be addressed to: ASD/ENES, Wright-Patterson AFB OH 45433-6503 by using the self-addressed Standardization Docu
2、mont Improvement Proposal (DD Form 1426) appearing at the end of this document or bv letter. A I INCH-POUND I MIL-C3095G (USAFI 25 November 1988 SUPERSEDING MIL-C-3095F (USAF) 25 January 1985 MILITARY SPECIFICATION -CAF, SERVICE, MANS, AIR FORCE t This specification is approved for use by the Depart
3、ment of the Air Force, and is available for use by all Departments and Agencies of the Department of Defense. -3 I 1. SCOPE A 1.1 Scope. This specification covers the requirements for a mans Air Force service cap. * 1.2 Classification. The cap shall be of one type in the following classes, as specif
4、ied (see 6.2): Class 1 - Polyester/wool tropical cloth, USAF Blue 1578, 10.00 oz. Class 2 - Polyester/wol tropical cloth, USAF Blue 1608, 10.25 oz. 1.2.1 Size. The cap shall be furnished in the following sizes, as specified (see 6.2) : 6-3/8 6-3/4 7-1/8 7- 1/2 7-7/8 6-1/2 6-718 7-114 7-5/ 6-5/8 7 7-
5、3/8 7-3/4 FSC 8405 * AMXC N/A * DISTRIBUTION STATEMENT A. Approved for public release; distribution is un1 imi ted. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-3095G 84 m 9999906 0373536 B MIL-c-30958 (USAF) 2. APFLICABLJI DOCUMENTS 2.1 Gov
6、ernment documents * 2.1.1 Specifications and standards. The fol lowing specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these docwnts are those listed in the issue of the Department of Defense Index of Specifications
7、and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL C-F-206 H-S-95 1 Felt Sheet: Synthetic Fi For L-P-375 L-P-390 V-T-276 V-T-295 NN-P-7 1 UU-P-258 UU-P-553 ccc-c-432 DDD-L-20 PPP-B-60 1 PPP -B - 63 6 PPP-T-45 MILITARY MIL-C-368 MIL-B-593 MIL-B-
8、346 1 MIL-s-3577 MIL-P-15011 MIL-(2-21115 MIL-(3-41831 MIL-L-43541 MIL-T-43548 Cloth, Felt, Wool, Pressed aments for Brushes; General Spec-fication Plastic Film, Flexible, Vinyl Chloride Plastic Molding and Extrusion Material, Polyethylene and Copolymers (Low, Medium, and High Density) Thread, Cotto
9、n Thread, Nylon Pallets, Material Handling, 2-Way And 4-Way (Partial) Paper, Index Paper, Wrapping, Tissue Wood, Stringer Construction, Cloth, Sheeting, Cotton, (Ur.dleached, Bleached, and Dyed) Label: For Clothing, Equipage, and Tentage, (General Use) Boxes, Wood, Coated-Plymod Boxes, Shipping, Fib
10、erboard Tape, Gunmed, Paper, Reinforced and Plain, for Sealing and Securing C.loth, Satin, Rayon and Cloth, Twill, Rayon Braid, Textile (Flat) Button, Insignia, Metal, Uniformand Cap Sweatband, Headmar, Leather Pallets, Material Handling, Wood Post Construction, the requirements for colorfastness to
11、 light and to laundering and for seam efficiency shall not apply: and the shrinkage shall not exceed 6 percent in the warp or the filling. The cotton sheeting shall be dyed to approximate the shade of the lining mterial specified in 3.3.2. The lining mterial or the cotton sheeting for the crown seam
12、 tape shall be bias cut 1-5/8 inches wide, with the raw edges overlapping 1/16 21/32 inch on the underside, to form binding. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-3075G BLt 7779906 0373537 3 MIL-C-3095G (USAF) 3.3.4 Interlining for
13、-crown seam tape. The interlining for the crown seam tape shall be bias cut, 3/4 11/16 inch wide, fromnatural or dyed nylon mesh. The nylon mesh shall be knitted on a single needle bar raschel and shall weigh 6 20.5 ounces per square yard. The stiffness, the length parallel to the wales of the finis
14、hed cloth, shall be 0.08 (minimud and 0.1 (niaxirrnn) load pound. The stiffness, the length across or perpendicular to the wales of finished cloth, shall be 0.04 (minimum) and 0.06 (niaXimm9 load pound (see 4.4.1). 3.3.5 Crown protector, personal label pocket, and binding. The mterial for the crown
15、protector, the personal label pocket, and the binding for the front interlining shall conform to type II, class 1 of L-P-375 and shall be 0.004 +0.0004 inch thick. 3.3.6 Visor cushion. The material for the visor cushion shall conform to type I, classification 9R4 of C-F-206 except that the niaterial
16、 shall be 114 inch thick and shall have fair colorfastness to wet dry cleaning. The visor cushion shall be cut 3/4 21/8 inch wide and shall be the length of the visor. In lieu of the felt pad, a 3/8 inch wide and 1/4 inch thick expanded foam polyvinyl chloride pad my be used. adhesive (see 4.4.1). .
17、 .3 It shall be attached with self 3.3.7 Swatband wlt. The material for the sweatband shall be pressed fiber. The pressed fiber shall weigh 1/5 to 2 ounces per square foot; shall be 0.015 to 0.2 inch thick; and shall be natural, red, or black (see 4.4.1). 3.3.8 Interlining for front. The interlining
18、 for the front shall be constructed of cloth, knitted, nylon raschel conforming to MIL-C-41831. 3.3.9 Inner body band. The niaterial for the inner body band shall be composed of a high alpha cellulose wood pulp sheet impregnated with an oil- resistant and perspiration-resistant synthetic rubber bind
19、er and shall conform to the requirements specified in table I or the inner body band shall be of high density (linear) polyethylene plastic material conforming to type III, class H, grades 1 or 2 of L-P-390, except that the low temperature brittleness, dielectric constant, dissipation factor and the
20、rml-stress cracking resistance properties shall not apply. shall be cut, extruded, stripped or slit 2 +i/lS inches in width and 0.030 - +0.002 inch in thickness. As an additional alternate the band my be made from imitation (mlded) linear polyethylene patterned on one or both sides, interlaced in a
21、chair seat design: shall be black; and shall finish 2 51/16 inches in width. The thickness of the material shall be 0.050 to 0.075 inch (see 4.4.1). The band 3.3.10 Wadding. The wdding shall be a good comercial cotton wadding that conforms to the requirements specified herein. The wadding shall be g
22、ray or vrihite, shall weigh not less than 2 ounces nor more than 2.5 ounces per square yard, and shall have good colorfastness to mt dry cleaning (see 4.4.1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-3075G 84 7777706 0373520 T MIL-C-3095
23、G (US 3.3.11 Thread. The cotton thread for seaming and stitching the caps shall ccnformto V-T-276 as indicated in table II or as an alternate, cotton- co%yre polyester threads, in equivalent sizes, conforming to MIL-T-43548 my be bed. The thread for fel 1 ing the sweatband to the band shall be black
24、 wd shall conform to type IV, letter size C of V-T-295. The thread for bartacking the front stiffener shall be either cotton-covered or rayon- . . covered polyester conforming to MIL-T-43548. 3.3.11.1 Colorfastness. The vat dyed threads shall show fastness to light and laundering equal to or better
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AIRFORCEMILC3095G1988CAPSERVICEMAN SAIRFORCE 空军 男式 服役 制服 PDF

链接地址:http://www.mydoc123.com/p-427574.html