AIR FORCE A-A-59724 C-2010 TRUCK FIRE FIGHTING (QUINT)《消防车(五件套)》.pdf

《AIR FORCE A-A-59724 C-2010 TRUCK FIRE FIGHTING (QUINT)《消防车(五件套)》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE A-A-59724 C-2010 TRUCK FIRE FIGHTING (QUINT)《消防车(五件套)》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: WR-ALC 542 CSW/CBSSS, 295 Byron Street, Robins AFB, GA 31098-1611. Since contact information can change, you may want to verify the currency of this address

2、 information using the ASSIST Online database at https:/assist.daps.dla.mil/online . FSC 4210 INCH-POUNDA-A-59724C 19 OCT 2010 SUPERSEDING A-A-59724 B 23 SEP 2010 COMMERCIAL ITEM DESCRIPTION TRUCK, FIRE FIGHTING (QUINT) The General Services Administration has authorized the use of this commercial it

3、em description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers a commercial Quint. It has a 4x2 or 6x4 chassis; a diesel engine; an automatic transmission; a cab with at least 4 doors with seating for at least five persons; a 1,250 gallon per minute (gpm) fire pump;

4、 a 500 gallon minimum capacity water tank; hose storage areas; a 75 foot aerial ladder with a pinnable/permanently mounted waterway; and equipment compartments. The Quint is intended to combat structural and similar type fires. 2. SALIENT CHARACTERISTICS. The Quint shall be in accordance with the ap

5、plicable requirements of the following chapters of National Fire Protection Association (NFPA) 1901, Standard for Automotive Fire Apparatus: Current Edition. Chapter Title 1 Administration 2 Referenced Publications 4 General Requirements 9 Quint Fire Apparatus 12 Chassis and Vehicle Components 13 Lo

6、w-Voltage Electrical Systems and Warning Devices 14 Driving and Crew Area 15 Body, Compartments, and Equipment Mounting 16 Fire Pump and Associated Equipment 19 Water Tanks 20 Aerial Devices 23 Line Voltage Electrical Systems Provided by IHSNot for ResaleNo reproduction or networking permitted witho

7、ut license from IHS-,-,-A-A-59724C 2 2.1 Administration. 2.1.1 Environmental conditions. 2.1.1.1 Altitude. Unless otherwise specified (see 6.2), the vehicle, including the pumping system, shall be designed for operation at or below 2,000 feet above sea level. 2.1.1.2 Temperature range. The vehicle s

8、hall be capable of satisfactory storage and operation in temperatures ranging from 0 to 125 F. The vehicle shall be equipped with a winterization system that extends the operational range of the vehicle. The winterization system shall protect the agent pump, agent piping systems, firefighting system

9、s, and water tank to 0 F. It shall also include the vehicle engine oil and coolant systems. While in operation, the appropriate systems requiring winterization shall be powered by the vehicle. While in storage, the winterization system shall be powered through the electrical shoreline connection (se

10、e 2.11.2). 2.1.2 Foreign object damage. All loose metal parts, such as pins, shall be securely attached to the vehicle with wire ropes or chains. “Dog tag“ style beaded chains shall not be provided. Removable panels, if provided, shall be attached with captive fasteners. 2.1.3 Roadability. 2.1.3.1 O

11、perating terrain. The vehicle shall operate on paved and graded gravel roads. 2.1.3.2 Acceleration. The fully loaded vehicle shall accelerate from 0 to 35 miles per hour (mph) within 25 seconds on a level, paved road. 2.1.3.3 Maximum speed. The fully loaded vehicle shall attain a minimum top speed o

12、f 50 mph on a level, paved road. 2.1.3.4 Gradeability. The fully loaded vehicle shall be able to maintain a speed of at least 20 mph while ascending any paved grade up to and including 6.0 percent. 2.1.4 Overall dimensions. Overall dimensions shall be the minimum consistent with the operational perf

13、ormance and the design constraints necessary to achieve the specified performance. Overall dimensions shall not exceed: Length 450 inches Width 102 inches (excluding mirrors) Height 144 inches 2.1.5 Turning diameter. The fully loaded vehicle shall have a wall to wall turning diameter of less than th

14、ree times the length of the vehicle. 2.1.6 Angles of approach and departure. The fully loaded vehicle shall have angles of approach and departure of not less than 8 degrees. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59724C 3 2.1.7 Vehicle S

15、tability. Vehicle shall comply with roll over stability criteria as defined by NFPA 1901, paragraph 4.13. 2.1.8 Manuals. 2.1.8.1 Technical manuals. The overall format for the manuals may be military specification, commercial, or a combination of both. Each technical manual shall have a title page. a

16、. The contractor shall validate the technical manuals for accuracy prior to submission to the procuring activity for verification. The contractor shall submit one complete set to the procuring activity for verification 30 days before the first production test. Any changes or corrections noted by the

17、 procuring activity shall be corrected and updated pages or manuals shall be submitted to the procuring activity. b. Once approved by the procuring activity, the contractor shall pack two complete sets of technical manuals with each vehicle. An additional two complete sets shall be submitted to the

18、procuring activity for stock. c. Once approved by the procuring activity and a Technical Order number is assigned, the contractor shall pack two complete sets of both hard copy and CDs with each vehicle and one complete set of both hard copy and CDs shall be submitted to the procuring activity for s

19、tock. The procuring activitys address will be provided. d. The contractor shall grant the United States Air Force a non-exclusive, non-assignable, royalty free U.S. Government (Government) Purpose License, to scan into CENTRA (the USAF repository) and to reproduce and distribute (either electronical

20、ly or via hard medium) copies or facsimiles of manuals produced and distributed by the contractor for this CID. These rights extend to Government agencies only, and the data contained in the technical manuals is not to be sold, disclosed or otherwise provided to any other entity or entities outside

21、the Government. The license shall remain in effect as long as the vehicles described in the required technical manuals remain under Government control and usage. In addition, the contractor shall grant permission for the Government to place an Air Force TO (Technical Order) number and publication da

22、te as well as distribution, warning, handling and destruction statements on the cover / title pages of the TO. 2.1.8.1.1 Operators manuals. The operators manual shall include all information required for the safe and efficient operation of the vehicle, including the fire extinguishing equipment, and

23、 any special attachments or auxiliary equipment. The operators manual shall include at least the following: a. Location and function of all controls and instruments shall be illustrated and fully described. b. Safety information that is consistent with the safety standards established by the Occupat

24、ional Safety and Health Administration (OSHA). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59724C 4 c. Checks and adjustments in preparation for placing the vehicle for service upon receipt from the contractor. d. Preparation for shipment or

25、storage. e. Warranty information and period of the warranty for the complete vehicle and for any component warranty that exceeds the warranty of the complete vehicle. Addresses and telephone numbers shall be provided for all warranty providers. f. General description of and step-by-step instructions

26、 for the operation of the vehicle and its fire extinguishing system(s) and auxiliary equipment. g. Description of the post-operational procedures (draining, flushing, et cetera). h. Checklists for the daily maintenance inspection and mission readiness checks that the operator is expected to perform.

27、 i. Procedures for towing a disabled vehicle. j. Schedules for required preventative maintenance and required periodic maintenance. 2.1.8.1.2 Service manuals. The service manual shall identify any special tools and test equipment required and shall cover troubleshooting and maintenance as well as mi

28、nor and major repair procedures. The text shall contain performance specifications, tolerances, and fluid capacities; current, voltage, and resistance data; test procedures; and such illustrations and exploded views as may be required to permit proper maintenance by qualified mechanics. The manual s

29、hall contain an alphabetical subject index as well as a table of contents. The service manual shall contain at least the following, where applicable: a. Fire fighting system schematic(s). b. Hydraulic schematic. c. Pneumatic schematic. d. Electrical schematic. e. Winterization schematic. f. Schedule

30、s for required preventative maintenance and required periodic maintenance. g. Location, procedure, and interval for parts of the truck and equipment which require lubrication. 2.1.8.1.3 Parts manual. The parts manual shall include illustrations and exploded views, as needed, to properly identify all

31、 parts, assemblies, subassemblies, and special equipment. All components of assemblies shown in illustrations or exploded views shall be identified by Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59724C 5 reference numbers which correspond to

32、the reference numbers in the parts lists. All purchased parts shall be cross-referenced with the original manufacturers name and part number. The parts identification manual shall provide the description, length, dimensions, and quantity of each item used per vehicle. The manual shall contain a nume

33、rical index. The parts manual shall contain a list of all of the component vendor names, addresses, and telephone numbers referenced in the parts list. 2.1.9 Painting, plating, and corrosion control. 2.1.9.1 Dissimilar metals. Dissimilar metals, as defined in MIL-STD-889, shall not be used in intima

34、te contact with each other. 2.1.9.2 Finish. Exterior surfaces shall be prepared, primed, and painted with polyurethane paint in accordance with all of the paint manufacturers instructions and recommendations. Unless otherwise specified (see 6.2), the exterior finish color shall be Candy Apple Red, S

35、ikkens Color Number FLNA3021, DuPont Color Number 97902U or 4737U, PPG Color Number 71528 (the PPG name for this color is Cardinal Red), or equal. When specified, the exterior finish color shall be Desert Sand, Color Number 30313 of FED-STD-595. a. For vehicles painted Candy Apple Red, the cab upper

36、 body (from the bottom of the windshield) and roof shall be painted White, Color Number 17875 of FED-STD-595. Compartment interiors shall have a standard commercial finish. All bright metal and anodized parts, such as mirrors, horns, light bezels, and treadplate, shall not be painted. Roll-up compar

37、tment doors may be painted or unpainted. b. For vehicles painted Desert Sand, all exterior surfaces, excluding all normally bright metal and anodized parts and any interior surfaces visible with any compartment door open (but not the interior of the cab), shall be painted body color. This includes c

38、ompartment shelves and mounting hardware, but does not include items mounted in the compartments. Non-metallic materials may be black or gray. 2.1.9.3 Reflective stripes. Horizontal, reflective stripes in accordance with 15.9.3 of NFPA 1901 shall be applied around the vehicle in an approximate plane

39、 with the headlights. Bright metal trim or anodized parts may interrupt the reflective stripes. The pattern shall be 10 inches wide with three reflective stripes (one inch reflective, one inch body color, six inches reflective, one inch body color, and one inch reflective). The reflective stripes sh

40、all be white for vehicles painted Candy Apple Red or Desert Sand. 2.1.9.4 Lettering. Vehicles painted Candy Apple Red shall have the letters UNITED STATES and AIR FORCE applied in synthetic or encapsulated gold leaf, with outline and black shadow, on the front door on both sides in long radius ellip

41、tical arches above and below the lettering center line. The size of the lettering shall be a minimum of 2-inches to a maximum of 6-inches. Vehicles painted Desert Sand shall have no lettering. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59724

42、C 6 2.1.9.5 Aerial Ladder Lettering. Vehicles painted Candy Apple Red shall also have synthetic or encapsulated gold leaf letters “U.S. AIR FORCE“ with outline and black shadow located on both side panels of the retracted ladder. Base names are not authorized. Vehicles painted Desert Sand shall have

43、 no lettering. 2.1.9.6 Chevron Striping. In accordance with 15.9.3.2 of NFPA 1901 at least 50 % of the rear-facing vertical surfaces, visible from the rear of the apparatus, excluding any pump panel areas not covered by a door, shall be equipped with retroreflective striping in a chevron pattern slo

44、ping downward and away from the centerline of the vehicle at an angle of 45 degrees. . 3M part number 983-17 (red) and 983 -23 (florescent yellow/green) reflective diamond grade or equivalent shall be utilized Each stripe in the chevron shall be a single color alternating between red and fluorescent

45、 yellow in accordance with 15.9.3.2.1. Each stripe shall be 6-inches (150 mm) in width in accordance with 15.9.3.2.2 of NFPA 1901 and the example provided below. 2.1.10 Identification plate. A permanently marked identification plate shall be securely mounted at the drivers compartment. The identific

46、ation plate shall contain the following information: a. NOMENCLATURE b. MANUFACTURERS MAKE AND MODEL c. MANUFACTURERS SERIAL NUMBER d. USAF VEHICLE REGISTRATION NUMBER Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59724C 7 e. NATIONAL STOCK NUM

47、BER (NSN) f. VEHICLE CURB WEIGHT: kg (pounds) g. PAYLOAD, MAXIMUM: kg (pounds) h. GROSS VEHICLE WEIGHT (GVW): kg (pounds) i. FUEL CAPACITY AND TYPE: gal (gallons) / L (liters) j. DATE OF DELIVERY (month and year) k. WARRANTY (months and km (miles) l. CONTRACT NUMBER m. PAINT COLOR AND NUMBER n. LENG

48、TH, WIDTH, AND HEIGHT OF VEHICLE IN INCHES AND CENTIMETERS. 2.2 General requirements. 2.2.1 Hose storage. 2.2.1.1 Hose storage area. The vehicle shall have a hose bed, with removable cover and two adjustable dividers, capable of carrying 1,000 feet of 5-inch hose and 800 feet of 2- or 3-inch hose. H

49、ose bed covers will be red for vehicles painted candy apple red and tan for desert sand vehicles. The hose storage area shall be equipped with a hose retention device to prevent inadvertent hose deployment. Covers will be secured by snap fasteners. 2.2.1.2 Cross lay hose beds. The vehicle shall have three cross lay hose beds with one or more removable covers. Two hose beds shall be capable