AIR FORCE A-A-58085-1996 TRUCK LIFT FORK ELECTRIC WALKIE REACH 3000 POUND CAPACITY 150 INCH MINIMUM LIFT [Superseded AIR FORCE MIL-T-83816 CANC NOTICE 1 AIR FORCE MIL-T-83816]《24英寸.pdf
《AIR FORCE A-A-58085-1996 TRUCK LIFT FORK ELECTRIC WALKIE REACH 3000 POUND CAPACITY 150 INCH MINIMUM LIFT [Superseded AIR FORCE MIL-T-83816 CANC NOTICE 1 AIR FORCE MIL-T-83816]《24英寸.pdf》由会员分享,可在线阅读,更多相关《AIR FORCE A-A-58085-1996 TRUCK LIFT FORK ELECTRIC WALKIE REACH 3000 POUND CAPACITY 150 INCH MINIMUM LIFT [Superseded AIR FORCE MIL-T-83816 CANC NOTICE 1 AIR FORCE MIL-T-83816]《24英寸.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、A-A-5O5 9999974 OL73000 T4b Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any data which may improve this document should be sent to: WR-ALCLVRE, 225 Ocmulgee Court, Robins AFB GA 3 108 8- 1647 L INCH-POUND A-A-58085 29 Nov 96 SUPERSEDING 3 1 July 1990 MIL-T-8
2、38 16 COMMERCIAL ITEM DESCRIPTION TRUCK, LIFT, FORK, ELECTRIC, WALKIE REACH, 3000 POUND CAPACITY, 150 INCH MINIMUM LIFT The General Services Administration has authorized the use of this commercial item description as replacement for MIL-T-838 16. 1. SCOPE. This commercial item description covers th
3、e general requirements for a battery powered, industrial type, walking operator forklift truck. 2. SALIENT CHARACTERISTICS. 2.1 Safety. The forklift shall comply with ANSI B56.1 , OSHA, and all other applicable standards in effect at the time of manufacture. Unless otherwise specified in the contrac
4、t, the final color shall be yellow for safe operation in an indoor environment. 2.2 Environmental requirements. The forklift shall be capable of continuous operation as specified herein at any ambient temperature fiom O degrees F to 120 degrees F. 2.3 Maintainabilitv. All maintenance and servicing f
5、unctions shall be capable of being performed using common hand tools. 2.4 Lubrication. Lubrication means shall be provided for all moving parts that require periodic lubrication. The types of lubricants shall be selected from and in accordance with SAE 5754. Grease lubrication fittings shall conform
6、 to SAE J534. 2.5 Fluid level indicator. All fluid level indicators shall be located where they are accessible without danger of bums or injury to the operator. The indicators shall be in an open area, or covered by a hinged panel that can be opened and closed without the need for tools. 2.6 Hvdrau
7、lic svstem. A pressure relief protection device is required along with pump(s), cylinders, control valves, filter(s), reservoir, hoses, and all other components necessary to make a complete hydraulic system(s). 2.7 Electric motors. Motors shall be industrial type. The insulation for motors shall be
8、class By F, or H as defined in NEMA standards. AMSC N/A FSC 3930 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-58085 9999974 0173001 982 A-A-58085 2.8 Battery. The battery shall have adequate capacity to provide not less than 8.0 hours of conti
9、nuous operation under normal industrial use. The battery mounted half connector shall be the “SB” type. 2.9 Forks. The fork and fork carrier shall conform to ANSI B56.1. Fork dimensions shall be 2.5 inches maximum thickness, 5 inches maximum width, and 35 to 42 inches in length. Fork thickness shall
10、 not exceed 0.5 inch at the tip, and there shall be a tapex on the underside of the forks not less than 14 inches long. 2.10 Fork positioner. The forks shall be capable of being laterally positioned manually without the need of tools. With the forks at their widest spacing, they shall spread at leas
11、t 27 inches, measured from the outside of the forks. With the forks at their narrowest spacing, they shall measure no more than 16 inches from outside to outside of the forks. 2.1 1 Load backrest. A metal backrest, or backrest with extension, shall be provided. There shall be no protruding bolts or
12、appendages beyond the side plane of the load backrest. The load backrest, in conjunction with fork and hanger design, shall provide a vertical rear guard at least 48 inches high measured from the load carrying surfaces of the forks. 2.12 Fork extension: Forks and load backrest shall be able to exten
13、d forward at least 24 inches from the rearmost position. 2.13 Service brakes. Service brakes conforming to ASMEIANSI B56.1 shail be hished. 2.14 Parking brake. Parking brake shall conform to ASME/ANSI B56.1. 2.15 Speed and direction controls. Speed and direction controls shall be in accordance with
14、ASME/ANSI B56.1. All load motion controls shall be self centering, that is they shall return to the neutral position when released. 2.16 m. A horn shall be furnished, with the horn actuator located within reach of the operator. 2.17 Contro 1s and insrumentation markings, All controls and instrumenta
15、tion shall be provided with position markings conforming to ASME/ANSI B56.11.3. 2.18 Indicators. The truck shall be equipped with a battery discharge indicator and an hour meter, both visible to the operator. 2.19 External lights. There shall be at least one sealed beam, 25 watts minimum, floodlight
16、 facing forward. 2.20 Painting. The forklift shall be primed and painted using standard commercial practices. The final color shall be yellow, unless otherwise specified. 2.21 Walkwav coating. Floor plates and step surfaces shall be coated with a non-slip coating compound or be furnished with a non-
17、slip metal surface in accordance with ASME/ANSI B56.1. 2.22 Electroma-etic interference (EM11 suppression. The truck shall control EM1 to meet the requirements of SAE J55 1. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I A-A-58085 9999974 037300
18、2 819 A-A-58085 2.23 Informational aids. All stencils, decals, plates, or other similar items, that are provided on the manufacturers standard product shall be included on the forklift. This shall include, but not be limited to: rated capacity, all cautions and warnings, and all references to safety
19、 related items. 2.24 Slinginp rovisions. Slinging devices that provide a means of attaching a shackle or ring to the forklift for safe lifting shall be furnished to allow the truck to be lifted by a crane in its normal operating position. Each device shall be not more than 1.0 inch thick. The openin
20、g in the device shall be at least 3.0 inches in diameter. Each slinging device, when loaded as the truck will be picked up, shall withstand a load of 2.3 times the static load on each device. The words “LIFT HERE“ shall be stenciled near each slinging device. If possible, the slinging devices may al
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
2000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AIRFORCEAA580851996TRUCKLIFTFORKELECTRICWALKIEREACH3000POUNDCAPACITY150INCHMINIMUMLIFTSUPERSEDEDAIRFORCEMILT83816CANCNOTICE1AIRFORCEMILT8381624

链接地址:http://www.mydoc123.com/p-427016.html