AIR FORCE A-A-50695-1992 DIES THREADING DIE HEAD《硬模模头线》.pdf

《AIR FORCE A-A-50695-1992 DIES THREADING DIE HEAD《硬模模头线》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE A-A-50695-1992 DIES THREADING DIE HEAD《硬模模头线》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、7 A-A-50b95 51 m 7799974 0064577 II m A-A-50695 March 27, 1992 SUPERSEDING MIL-D-4562(USAF) March 16. 1981 COMMERCIAL ITEM DESCRIPTION DIES, THREADING, DIE HEAD The General Services Administration has authorized the use of this Commercial item description (CID) as a replacement for MIL-D-4562(USAF)

2、which is canceled. Abstract : This CID covers self-opening dies complete with adjustable and removable dies of such design and construction as to operate on hand turret lathes. Salient Characteristics: 1. Design. The die head and dies shall be new and of the manufacturers commercial design in effect

3、 on the date of the solicitation, and shall meet the requirements specified herein and conform to current industrial practices. 2. Die head. The die head shall accommodate four thread dies and have provisions to securely hold the dies in proper position for threading, and shall be readily and easily

4、 adjustable to obtain proper pitch diameter, and shall be removable to allow die changes. Provisions shall be made to automatically open the dies at a predetermined length of thread. A manually operated device for opening the dies by hand shall also be provided. The length and diameter of the die he

5、ad shank, and the maximum outside diameter of the die head, shall be as specified in the contract. Beneficial comments, recommendations, additions, deletions clarifications, etc. and any data which may improve this document should be sent to: WR-ALC/LZMD, Robins AFB, GA 31098-5365 AMSC NIA FSC 5136

6、DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. (d Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50695 51 9999974 0064598 3 m A-A-50695 3. Dies. Dies shall be capable of threading to within one thread from a sh

7、oulder without seriously marring the face of the shoulder. Dies shall be suitably hardened and tempered to cut consistent, smooth, well-defined NPT, ANPT or straight threads in the sizes and material as specified in the contract. 4. Cet. One cet of dies shall consist of the number of aies required f

8、or use in a die head to cut one size of thread. 5. Interchangeability. All parts shall be manufactured to such standards that will permit replacement or adjustment without modification of the tool assembly. 6. Marking. All dies shall be marked with their thread series and size. Marking shall be legi

9、ble and permanent. Contractor certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this CID, and that the product conforms to the producers own drawings, specifications, standards, and quality assurance practic

10、es. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Regulatory requirements. In accordance with section 23.403 of the Federal Acquisition Regulations, the Governments

11、policy is to acquire items composed of the highest percentage of recovered materials practicable, consistent with maintaining a satisfactory level of competition without adversely affecting performance requirements or exposing suppliers employees to undue hazards from the recovered materials. Respon

12、sibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection, examination, and test requirements specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his

13、 own or any other facilities suitable for the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections, examinations, or tests set forth in this description where such inspections, examinations, and tests are

14、deemed necessary to assure supplies and services conform to prescribed requirements. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50695 51 = 9999974 0064579 5 Quantity of i tems being purchased A-A-50695 Sample size Responsibility for compli

15、ance. e All items shall meet all requirements of salient characteristics paragraphs, The inspection set forth in this description shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the description shall not relieve the c

16、ontractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, th

17、is does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. Sampling inspection. As a minimum sampling inspection, the supplier shall randomly select the number of samples in Table I that is applicable to t

18、he quantity of items being purchased. Each sample item shall be inspected to determine conformance with the test. Should any of the sample items fail to meet the test below, the entire lot shall be considered defective and unsuitable for acceptance. A lot is defined as all items presented at one tim

19、e for acceptance. TABLE I. Sampling plan. 2 to 8 9 to 15 16 to 25 26 to 50 51 to 90 91 to 150 Test. Each selected die head shall be tested under actual conditions using a set of dies selected at random from the dies to be supplied on the order or contract. Cutting tests shall be conducted on the mat

20、erials for which the dies have been specified in the order or contact, and be capable of producing consistent, smooth, well-defined threads through ten consecutive operations. Preservation, packaging, packing. and marking. Preservation packaging, packing, labeling, and marking shall be as specified

21、in the contract. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-No tes I Ordering data. Purchasers should select the preferred options permitted herein, and include the following information in procurement documents: a. Title, number, and date of

22、this CID. b. Series and size of dies required c. Length and diameter of the shank. d. Maximum outside diameter of the die head. e. Material to be threaded. f. Type of preservation, packaging, packing, and marking required. MILITARY INTEREST: Custodian Air Force - 99 4 CIVIL AGENCY COORDINATION ACTIV

23、ITY: GSA-FCC PREPARING ACTIVITY Air Force - 84 AGENT Air Force - 99 Project 5136-F045 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50695 51 9999974 0064601 T W The illustration shown is far the convenience of identification, requisitioning, and pi-irchasing, and ic nt intended to preclude the purchase of die heads ot- chasers which are atherwise in accordance with the requirements of this spetif icatian. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-