AGMA 13FTM10-2013 Calculation of the Tooth Root Load Carrying Capacity of Beveloid Gears.pdf

《AGMA 13FTM10-2013 Calculation of the Tooth Root Load Carrying Capacity of Beveloid Gears.pdf》由会员分享，可在线阅读，更多相关《AGMA 13FTM10-2013 Calculation of the Tooth Root Load Carrying Capacity of Beveloid Gears.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、13FTM10 AGMA Technical Paper Calculation of the Tooth Root Load Carrying Capacity of Beveloid Gears By C. Brecher, M. Brumm and J. Henser, RWTH Aachen University2 13FTM10 Calculation of the Tooth Root Load Carrying Capacity of Beveloid Gears Christian Brecher, Markus Brumm and Jannik Henser, RWTH Aa

2、chen University The statements and opinions contained herein are those of the author and should not be construed as an official action or opinion of the American Gear Manufacturers Association. Abstract In this paper, two developed methods of tooth root load carrying capacity calculations for bevelo

3、id gears with parallel axes are presented. The first method calculates the tooth root load carrying capacity in an FE-based approach. The initial step of the method is the manufacturing simulation in the WZL software GearGenerator. The manufacturing simulation calculates the 3D geometry of the bevel

4、oid gears by simulating the generating grinding process. The next step is an FE-based (finite element) tooth contact analysis with the WZL software ZaKo3D which is able to calculate the tooth root stresses of several gear types during the meshing. From these stresses and further parameters (e.g., lo

5、cal material properties) the tooth root load carrying capacity is calculated in an approach which is based on the weakest link model of Weibull. The second method uses analytic formulas to calculate the tooth root load carrying capacity of beveloid gears. In this method the tooth root load carrying

6、capacity of beveloid gears is compared to the tooth root load carrying capacity of cylindrical gears. The effects which are observed during this comparison are described and formulas are derived to take these effects into account. Finally both methods are applied to a test gear. The methods are comp

7、ared to each other and to tests on beveloids gears with parallel axes in test bench trials. Copyright 2013 American Gear Manufacturers Association 1001 N. Fairfax Street, Suite 500 Alexandria, Virginia 22314 September 2013 ISBN: 978-1-61481-067-4 3 13FTM10 Calculation of the Tooth Root Load Carrying

8、 Capacity of Beveloid Gears Christian Brecher, Markus Brumm and Jannik Henser, RWTH Aachen University Introduction and challenge A particular gear type which becomes more and more important is the beveloid gear, also known as conical involute gear. This is mainly due to their ability to realize smal

9、l crossing angles between shafts and they can be produced economically on conventional gear grinding machines 1, 2. Beveloid gears have been used in marine applications, for example, for many years 3, 4, 5. In recent years the use of beveloid gears in the automotive sector has increased 6, 7. Here t

10、he beveloid gear is used, for example in four wheel drives to transmit torque and rotation from the output of the gearbox to a front axle that may not be parallel. Geometrical characteristics of beveloid gears Beveloid gears are used to transmit torque and rotation between elements of crossing, skew

11、 or parallel axes 6. The geometry of beveloid gears is derived from cylindrical spur or helical gears. The base circle and the pitch circle of beveloids are cylindrical, as presented in the middle section Figure 1. The pitch and the module are constant along the tooth width. The difference between b

12、eveloid gears and cylindrical gears is the varying profile shift along the tooth width to realize crossed or skew axes. For realizing the varying profile shift, the root cone angle fis defined which is generated during gear cutting and gear grinding by a change of the feed during the process. The fo

13、rm of the tip of a beveloid gear is usually conical. The tip cone angle ais determined by the geometry of the work piece. A special use of beveloid gears is the arrangement with parallel axes. This is realized by two meshing beveloids which have a cone angle of the same absolute value but with oppos

14、ite orientation 2. Another gear type which is used for realizing crossing or skew axes is the bevel gear. Bevel gears have a conical pitch and base envelope. This results in a varying module m along the tooth width 2. Beveloids are usually preferred to bevel gears when small crossing angles must be

15、realized due to manufacturing limits of bevel gears. This is related to the long cone distances of gears with small cone angles which require substantial dimensions of the bevel gear cutting machine. 8 Figure 1. Geometrical characteristics of beveloid gears 2 ( WZL) Spur Gear Beveloid Bevel Gearmlmr

16、ml= mrmlmrml mrmlmrml= mrx = const. x const. x = const.dbddbddbd4 13FTM10 Contact behavior of beveloid gears Beveloid gears can be mounted with parallel, crossed or skew axes. The axis orientation has substantial influence on the gear mesh. This influence is presented in Figure 2. In the left part o

17、f Figure 2 a typical contact pattern of beveloid with parallel axes is presented. The contact pattern is spread over the whole flank. On the right part of Figure 2 a typical contact pattern of beveloid gears with crossed axes is illustrated. Two involute beveloid gears with crossed axes have point c

18、ontact. The resulting contact pattern is narrower than the contact pattern of beveloid gears with parallel axes. To achieve a full contact pattern of beveloid gears with crossed or skew axes at least one gear has to be designed with non-involute flanks. In this case, the manufacturing with standard

19、methods like generating grinding is no longer possible. For some applications beveloid gears with conjugated flanks are manufactured by topological grinding to achieve nearly full contact 6 but for most applications this manufacturing method is avoided for economic reasons. Challenge To achieve a hi

20、gh power/weight ratio, a precise calculation of the gear load and load carrying capacity is necessary to design gears in an economical way. At the state of the art, no approved method for the tooth root load carrying capacity calculation for beveloid gears exists. Therefore the beveloid gear is appr

21、oximated by a substitute spur gear with the gear data of the middle transverse section of the beveloid gear. The inaccurateness of this method is shown in Figure 3. In the diagrams the tooth root stresses of a beveloid gear and a substitute spur gear are compared. The beveloid gear has an axis angle

22、 of 7.2. The substitute spur gear is derived from the gear data of the middle transverse section of the beveloid gear. It can be seen that the stresses of the beveloid are significant higher. Reasons for this are the different root fillet geometry and the different contact behavior. Thus the calcula

23、tion of the tooth root load carrying capacity of beveloid gears with a substitute spur gear according to existing standards for cylindrical gears is not possible without further ado. A more precise calculation method can lead to a better design of beveloid gears with a higher power/weight ratio. Fur

24、thermore no simulation method for the running behavior of beveloid gears with and without load exists. Such a method could determine the tooth root load carrying capacity for a large number of variants in a short time. Therefore the project “Development and Verification of a Method to Calculate the

25、Tooth Root Load Carrying Capacity of Beveloid Gears”, which is sponsored by the German research funding organization DFG (Deutsche Forschungsgemeinschaft) has been initialized. Figure 2. Contact characteristics of beveloid gears ( WZL) 5 13FTM10 Figure 3. Comparison of the tooth root stresses of a b

26、eveloid gear and its substitute cylindrical gear ( WZL) Objective and approach In this paper the development of two calculation methods for the tooth root load carrying capacity of beveloid gears with parallel axes is described. In Error! Reference source not found. the approach for the development

27、of these methods is illustrated. The initial point is the determination of the tooth root fatigue strength of beveloid gears on a test rig. The results are used to validate a local based calculation method to calculate the tooth root load carrying capacity of beveloid gears. Figure 4. Approach for d

28、eveloping calculation methods for tooth root load carrying capacity of beveloid gears ( WZL) Gear Datam = 2,5 mma=0 mm =7,2b = 35 mmz1=31z2=35 TorqueM2=200 NmBeveloid Gear Substitute Spur Gear01002003000246Pitch - Comparison Stressin theRootN/mm01002003000246Comparison Stressinthe Root N/mmPitch - B

29、eveloid / Substitute Spur GearMating GearConclusion:The calculation of the tooth root load carrying capacity of bevloidgears with a substitute spur gear according to existing standards for cylindrical gears is not possible without further ado.6 13FTM10 The initial step of the local based calculation

30、 method is the manufacturing simulation with the WZL software GearGenerator. In the manufacturing simulation, a 3D geometry of the beveloid gears is created by simulating the generating grinding process 1, 9. The resulting beveloid geometries are used in an FE-based tooth contact analysis with the W

31、ZL software ZaKo3D which is able to calculate the tooth root stresses of several gear types during the meshing 10. From these stresses and further parameters (e.g., local material properties) the tooth root load carrying capacity is calculated in an approach which is based on the weakest link model

32、of Weibull 11, 12, 13. After the local based calculation method is validated, this method is used to derive a standard based calculation method for beveloid gears. The standard based calculation method uses analytic formulas to calculate the tooth root load carrying capacity of beveloid gears. In th

33、is method the tooth root stresses of beveloid gears are compared to the tooth root stresses of cylindrical gears. The effects which, observed during this comparison, are described and formulas are derived to take these effects into account. Test bench trials To detect the tooth root bending strength

34、 of a beveloid gear, a back-to-back test rig is used according to DIN 51354 Part 1, which uses the power circuit principle. The setup is illustrated in Figure 5. The tested beveloid gears are mounted in a gear box. They are connected by shafts to a transmission gear box. This setup is called power c

35、ircuit. The test gear box is equipped with cylindrical gears. The cylindrical gears have the same gear data as the beveloids, but the cone angle is = 0. The profile shift of the cylindrical gears is taken from the middle section of the beveloid gears. To avoid damage, the test gears are designed sig

36、nificantly wider than the beveloid gears. It is possible to include a torque into the power circuit at the coupling which is mounted at one of the shafts. The other shaft is designed as torque shaft. An electric motor is used to drive the gears. Since the torque is realized by the power circuit, the

37、 motor only needs to apply power into the system which corresponds to the power losses due to e.g., friction. The gear data of the test gears is presented on the left side of Figure 6. To use the test principle of the back-to-back test rig according to DIN 51354 Part 1 parallel axes are used with a

38、center distance of a = 91.5 mm. The module of the gears is mn= 2 mm, the helix angle is 1/2= 23.024 and the number of teeth are z1/2= 45/39. Furthermore the cone angle of gear 1 is 1= 3.6. To realize parallel axes, the cone angle of gear 2 is 2= -3.6. Goal of the tests is to determine the fatigue li

39、mit of the test gears for a probability of survival of PS= 50%. The principle used is the staircase method according to Hck. In this method the test load is dependent on the result of the previous test run. The load is reduced at breakage and increased at run-out. In these tests the load step is fix

40、ed at T2= 25 Nm. A complete test run is reached, if gear 2 experiences n2= 3 000 000 load cycles without root breakage. Figure 5. Back-to-back gear test rig according to DIN 51354 Part 1 ( WZL) 7 13FTM10 Figure 6. Result of the test bench trials ( WZL) The results of the test are presented on the ri

41、ght side of Figure 6. In the diagrams the test results are marked at the torque which was used in each test. The cross represents a breakage during the test, a filled circle represents test run-out. Invalid results are marked with a void circle. To take the test result of the last test (damage or te

42、st run-out) into account, a fictitious point is added after the last test. The fictitious point is marked with a void square. For the evaluation, all valid points and the fictitious point are used. This results in a torque for a probability of survival of 50% of T2= 563.64 Nm for flank 1 and of T2=

43、565.91 Nm for flank 2. The fatigue strengths of both flank sides are similar. Local based calculation of tooth root load carrying capacity The first method to calculate tooth root load carrying capacity of beveloid gears is a local based method. In this method the probability of survival is calculat

44、ed locally for each point in the tooth root. In the next section the calculation is presented briefly. This is followed by the application of the calculation method to the test gears which were already used for the test rig trials in the previous chapter. Simulation method In this approach three pro

45、grams are used in sequence to calculate tooth root load carrying capacity for beveloid gears. Figure 7 gives a brief overview of the three programs. The first program in the simulation chain is the software GearGenerator which calculates a 3D-model of the beveloid gear by generating grinding simulat

46、ion. The software is based on the calculation method of Rthlingshfer 14, 1. The simulation uses the tool data, the gear data and the information about the axis setup of the machine (e.g., tilting or linked feeds) to calculate the tool geometry, the tool movements and finally the resulting gear geome

47、try according to the law of gearings 15. A 3D-model of the gear is provided as output. For the micro-geometry analysis the resulting geometry is compared to an ideally shaped involute and then plotted as profile and lead plot. Supplementing the manufacturing simulation, an algorithm was developed ac

48、cording to the VDI (Verein Deutscher Ingenieure) standard VDI 2607 to evaluate the flank deviations 16, 9. The excellent simulation accuracy of this method is shown by Rthlingshfer in chapter 5.3.2 of his dissertation 1. The 3D models of the gears which are generated by the software GearGenerator ar

49、e used as input for the tooth contact analysis software ZaKo3D. The general approach of ZaKo3D is the simulation of the 3D tooth contact. Therefore the geometric data of the flank and an FE-model of a gear section are needed as input. Furthermore pitch and assembly deviations can be considered. During the simulation, the contact distances, loads and deflections on the tooth are calculated. The results of the calculation can be displayed in established diagrams to support the gear designer during