AECMA PREN 4604-001-2008 Aerospace series Cable electrical for signal transmission Part 001 Technical specification Edition P3《航空航天系列.信号传输用电缆.第001部分 技术规范.版本P3》.pdf

《AECMA PREN 4604-001-2008 Aerospace series Cable electrical for signal transmission Part 001 Technical specification Edition P3《航空航天系列.信号传输用电缆.第001部分 技术规范.版本P3》.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 4604-001-2008 Aerospace series Cable electrical for signal transmission Part 001 Technical specification Edition P3《航空航天系列.信号传输用电缆.第001部分 技术规范.版本P3》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、ASD STANDARD NORME ASD ASD NORM prEN 4604-001 Edition P 3 April 2008 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Avenue de Tervuren, 270 - B-1150 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: 49.060 Supersedes edition P 2

2、March 2002 Descriptors: ENGLISH VERSION Aerospace seriesCable, electrical, for signal transmission Part 001: Technical specification Srie arospatiale Cbles lectriques pour transmission de signaux Partie 001 : Spcification technique Luft- und Raumfahrt Elektrische Leitungen fr Signalbertragungen Teil

3、 001: Technische Lieferbedingungen This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically appr

4、oved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examinat

5、ion and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national lev

6、el by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 30 April 2008 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2008 by ASD-STAN Cop

7、yright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4604-001:20082 Contents Page Foreword2 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Materials and construction of cables 3 5 Required ch

8、aracteristics.4 6 Test methods4 7 Quality assurance8 8 Identification, marking and colour.9 9 Packaging, labelling and delivery length 9 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with th

9、e rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4604-001:20083 1 Scope This standa

10、rd specifies the required characteristics, test methods, qualification and acceptance conditions of signal transmission electrical cables. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited ap

11、plies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2574, Aircraft Electrical cables Identification marking. EN 3475-100*, Aerospace series Cables, electrical, aircraft use Test methods Part 100: General. EN 3838, Aerospace series Requ

12、irements and tests on user-applied markings on aircraft electrical cables. 1)EN 9133, Aerospace series Quality management systems Qualification Procedure for aerospace standard parts. TR 6058, Aerospace series Cable code and identification list. 2)3 Terms and definitions For the purposes of this doc

13、ument, the terms and definitions given in EN 3475-100 apply. 4 Materials and construction of cables 4.1 General The composition, dimensions and mass of the cable shall conform to the characteristics below, as well as the values specified in the product standards. 4.2 Conductor 4.2.1 Material See pro

14、duct standards. 4.2.2 Construction See product standards, conductor shall not be spliced. 4.3 Dielectric See product standards. *And all parts quoted in Table 1. 1) Published as ASD Prestandard at the date of publication of this standard. 2) Published as ASD Technical Report at the date of publicati

15、on of this standard. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4604-001:20084 4.4 Screening 4.4.1 Material The materials used for screening are defined in the product standards. The screen stran

16、ds or strips shall be free of kinks or cracks and their surface shall have no corrosion at all or any other impurities. 4.4.2 Construction Construction shall be in accordance with the product standard. Splices of the individual strands or strips may be effected by brazing, soldering or folding in. T

17、he number of splices shall not exceed 1 per 3 m length of cable. 4.4.3 Screen coverage The screen is constructed in such a way that the screen meets the electrical requirements defined in the product standards. 4.5 Outer jacket See product standards. 4.6 Colours of components and jacket See product

18、standards. 5 Required characteristics The characteristics of the cables, tested according to the methods described hereafter shall comply with the values given in the product standards. 6 Test methods See Table 1. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduct

19、ion or networking permitted without license from IHS-,-,-prEN 4604-001:2008 5 Table 1 Tests: methods, application, requirements Tests Each delivery No. Description EN 3475- (and/or particulars) Qualification a( 7.1) On all cables ( 7.2.1 and 7.2.2) Prior to delivery( 7.2.1 and 7.2.3) Periodic Every

20、3 years ( 7.2.4)Requirements (and/or particulars) 6 General 100 X X X X 6.1 Visual examination 201 3 X Marking: Clause 8 6.2 Mass 202 3 X Product standard 6.3 Dimensions (all) - outer diameter 203 3 X Product standard 6.4 Ohmic resistance per unit length 301 3 X Product standard 6.5 Voltage proof te

21、st: - dielectric dry test - jacket immersion test - jacket dry test 302 X 3 X X X 1 Product standard 6.6 Insulation resistance - dry test - immersion test 303 3 X Product standard 6.7 Surface resistance 304 3 X Product standard 6.8 Overload resistance 305 NOT APPLICABLE 6.9 Continuity of conductors

22、306 1 X 6.10 Corona extinction voltage 307 3 X Product standard 6.11 Accelerated ageing 401 NOT APPLICABLE 6.12 Shrinkage and delamination 402 NOT APPLICABLE 6.13 Delamination and blocking 403 NOT APPLICABLE 6.14 Thermal shock 404 NOT APPLICABLE 6.15 Bending at ambient temperature 405 NOT APPLICABLE

23、 6.16 Cold bend test 406 Mandrel and load: Product standard 3 X Product standard 6.17 Flammability 407 Load: Product standard 3 X 6.18 Fire resistance 408 NOT APPLICABLE 6.19 Air-excluded ageing 409 NOT APPLICABLE 6.20 Thermal endurance 410 NOT APPLICABLE 6.21 Resistance to fluids411 1 per fluid X 6

24、.22 Humidity resistance 412 NOT APPLICABLE (continued) Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4604-001:20086 Table 1 Tests: methods, application, requirements (continued) Tests Each delivery

25、No. Description EN 3475- (and/or particulars) Qualification a ( 7.1) On all cables( 7.2.1 and 7.2.2) Prior to delivery( 7.2.1 and 7.2.3) Periodic Every 3 years ( 7.2.4)Requirements (and/or particulars) 6.23 Wrap back test 413 NOT APPLICABLE 6.24 Differential scanning calorimeter (DSC test) 414 NOT A

26、PPLICABLE 6.25 Rapid change of temperature 415 1 X Product standard 6.26 Thermal stability 416 1 X Product standard 6.27 Fire resistance of cables confinned inside a harness 417 NOT APPLICABLE 6.28 Thermal endurance for conductors 418 applicable (for 4604-009 type KW) 6.29 Dynamic cut-through 501 NO

27、T APPLICABLE 6.30 Notch propagation 502 Cut depth: Product standard 3 X 6.31 Scrape abrasion 503 Load: Product standard 3 X Requirements to be considered at 20 C unless otherwise specified 6.32 Torsion 504 NOT APPLICABLE 6.33 Tensile test on conductors and strands 505 3 X Product standard 6.34 Plati

28、ng continuity 506 3 X 6.35 Adherence of plating 507 3 X 6.36 Plating thickness 508 3 X Product standard 6.37 Solderabilty 509 3 X 6.38 Tensile strength and elongation of extruded insulation, sheath and jacket material 510 NOT APPLICABLE 6.39 Cable-to-cable abrasion 511 NOT APPLICABLE 6.40 Flexure en

29、durance 512 3 X Product standard 6.41 Deformation resistance (Installation with plastic cable ties) 513 4 X Product standard 6.42 Porosity of copper cladding on aluminium strands 514 3 X (continued) Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networki

30、ng permitted without license from IHS-,-,-prEN 4604-001:20087 Table 1 Tests: methods, application, requirements (concluded) Tests Each delivery No. Description EN 3475- (and/or particulars) Qualification a( 7.1) On all cables ( 7.2.1 and 7.2.2) Prior to delivery( 7.2.1 and 7.2.3) Periodic Every 3 ye

31、ars ( 7.2.4)Requirements (and/or particulars) 6.43 Crush resistance 515 3 X Product standard 6.44 Smoke density 601 3 Product standard 6.45 Toxicity 602 3 Product standard 6.46 Resistance to wet arc tracking 603 NOT APPLICABLE 6.47 Resistance to dry arc propagation 604 NOT APPLICABLE 6.48 Wet short

32、circuit test 605 NOT APPLICABLE 6.49 Strippability and adherence of insulation to the conductor 701 3 X Product standard Stripping length 75 mm 6.50 Screen pushback capability 702 3 X 6.51 Permanence of manufacturers marking 703 3 X Not applicable to marked tapes under transparent cable jacket 6.52

33、Flexibility 704 3 X Product standard Permanence of user-applied marking EN 3838 X X Product standard 6.53 Contrast measurement 705 Laser markability: 706 1 X Product standard 6.54 Capacitance per unit length 801 3 X Product standard 6.55 Capacitance unbalance 802 NOT APPLICABLE 6.56 Capacitance vari

34、ation 803 NOT APPLICABLE 6.57 Velocity of propagation 804 3 X Product standard 6.58 Characteristic impedance 805 3 X Product standard 6.59 Attenuation 806 3 X Product standard 6.60 Transfer impedance 807 1 X Product standard 6.61 Cross-talk 808 NOT APPLICABLE 6.62 Resistance unbalance 809 NOT APPLIC

35、ABLE 6.63 Structural return loss 810 NOT APPLICABLE 6.64 Unbalance attenuation 811 NOT APPLICABLE 6.65 Return loss (VSWR) 812 3 X Product standard aNumber of specimens per cross-section for each test unless otherwise specified Copyright ASD-STAN Provided by IHS under license with AECMA Not for Resal

36、eNo reproduction or networking permitted without license from IHS-,-,-prEN 4604-001:20088 7 Quality assurance 7.1 Qualification 7.1.1 General requirements See EN 9133. 7.1.2 Qualification conditions The cables shall be submitted for qualification tests on drums, spools or in coils in sufficient leng

37、ths, wound evenly and uniformly. Each drum, spool or coil shall have a label containing information given in 9.1. 7.1.3 Qualification tests See Table 1. 7.2 Acceptance test 7.2.1 Required conditions 7.2.1.1 General See Table 1. The acceptance tests shall be carried out on cables delivered against an

38、 order to check that the cable characteristics are maintained. 7.2.1.2 Tests to be carried out on all cables The cables which fail any of the tests specified in 7.2.2 shall be rejected. 7.2.1.3 Random sampling tests: retest If any of the specimens fails one of the tests specified in 7.2.3, that test

39、 shall be repeated on another set of specimens selected at random from the same batch. If one of these new specimens fails the test, the batch submitted for acceptance shall be rejected. 7.2.2 Production routine tests The tests shall be carried out on all cables delivered. See Table 1. 7.2.3 Tests p

40、rior to delivery They shall be carried out by sampling on each delivery batch. See Table 1. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4604-001:20089 7.2.4 Periodic tests They shall be carried ou

41、t by sampling at least every three years. Unless otherwise indicated the “X” means applicable at the same condition specified for qualification. See Table 1. 8 Identification, marking and colour 8.1 Identification See product standards. 8.2 Marking It is applied to the outer sheath or on a tape bene

42、ath a transparent outer jacket. See TR 6058, clause “Marking since March 1998” but without specific and AWG-cable size code. 8.3 Colour The colour of the marking is in accordance with ISO 2574 if not otherwise defined in the product standard. 9 Packaging, labelling and delivery length 9.1 Packaging

43、and labelling Cables supplied on drum, spools or in coils shall be wound evenly and uniformly. All cable ends shall be easily accessible and protected where necessary. Each drum, spool or coil shall have a label indicating: manufacturers name and designation; cable designation according to the EN pr

44、oduct standard; batch number; date of manufacture (month, year); inspectors mark; total length and length of each piece of cable in metres from inside to outside. 9.2 Delivery length Delivery length see product standards. Copyright ASD-STAN Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-