AECMA PREN 3020-1992 Aerospace Series Self-Locking Plate Nuts Floating Two-Lug in Heat Resisting Steel FE-PA92HT (A286) Silver Plated Classification 1 100 MPa (at Ambient Temperat.pdf

《AECMA PREN 3020-1992 Aerospace Series Self-Locking Plate Nuts Floating Two-Lug in Heat Resisting Steel FE-PA92HT (A286) Silver Plated Classification 1 100 MPa (at Ambient Temperat.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 3020-1992 Aerospace Series Self-Locking Plate Nuts Floating Two-Lug in Heat Resisting Steel FE-PA92HT (A286) Silver Plated Classification 1 100 MPa (at Ambient Temperat.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、CEN PREN*3020 92 3404589 O031836 173 W Edition approved for publication 1992-08-31 A. E.C. M .A. STAN DARD NOR ME A.E.C. M.A. A.E.C.M.A. NORM Comments should be sent within six months C8 Chairman after the date of publication decision A E.C M A M. WILLIAMS prEN 3020 Issue P 2 August 1992 UDC : EDITE

2、 PAR LASSOCIATION EUROPEENNE DES CONSTRUCTEURS DE MATRIEL AEROSPATIAL Technopolis - 175. rue Jean-Jacques Rousseau - F-92138 Issy-les-Moiilineaux Cdex - T1 (1) 47 36 98 76 Supersedes issue P1 October 1989 Key words : ENGLISH VERSION Aerospace series Self-locking plate nuts, floating, two-lug, in hea

3、t resisting steel silver plated (at ambient temperature) /650 OC FE-PA92HT (A286). Classification : 1 I O0 MPa Srie arospatiale crous river freinage interne, flottants, double patte, en acier rsistant chaud argents Classification : 1 100 MPa ( temprature ambiante) / 650 OC FE-PA92HT (A286). Luft- un

4、d Raumfahrt Selbstsichernde Annietrnuttern, beweglich, beidseitiger Flansch, aus hochwarmfestem Stahl versilbert (bei Raumtemperatur) /650 OC FE-PA92HT (A286). Klasse : 1 1 O0 MPa This .Aerospace Series pre-standard has been drawn up under the responsibility of AECMA (Association Europenne des Const

5、ructeurs de Matriel Arospatial). It is published on green paper for the needs of AECMA-Members. If has been technically approved by the experts of the concerned Commission following comment by the Member countries. Subsequent to the publication of this pre-standard, the technical content shall not b

6、e changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Official Services of the Member countries it will be submitted as

7、 a draft European Standard to CEN (European Committee for Standardization) for final vote. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-CEN PRENM302

8、0 92 3404589 0031837 OOT prEN 3020 Page 3 1 Scope and field of application This standard specifies the characteristics of self-locking, floating plate nuts in FE-PA92HT, silver plated, for aerospace applications. Ciassification : 1 1 O0 MPa l) / 650 OC 2, 2 References IS0 5855-2, Aerospace - MJ thre

9、ads - Part 2 : Limit dimensions for bolts and nuts EN 2399, EN 2424, EN 2786, EN 3004, EN 3638, EN 3639, Heat resisting steel FE-PA92-HT - R, 2 900 MPa - Bars for forged bolts - D I 25 mm - Aerospace series 3, Aerospace series - Identification marking of standard fasteners 3, Aerospace series - Elec

10、trolytic silver plating of fasteners 4, Aerospace series - Nuts, self-locking, in heat resisting steel FE-PA92HT (A2861 - Classification : 1 100 MPa / 650 OC - Technical specification 5, Aerospace series - Heat resisting steel FE-PA92HT - Solution treated - Sheets and strips - a s 3 mm 4) Aerospace

11、series - Heat resisting steel FE-PA92HT cold worked and softened - Bars and wires for continuous cold forging or extrusion of fasteners - 3 mm L D I 30 mm - R, 2 900 MPa 4, 3 Required characteristics 3.1 Configuration - Dimensions - Tolerances - Masses See figure 1 and table 1. Dimensions and tolera

12、nces are in millimetres. They apply after silver plating. 3.2 Material Nut element : EN 2399, EN 3638 or EN 3639 Cage : EN 3638 3.3 Surface treatment EN 2786, only nut element Thickness : - External surface : 5 pm bis 15 pm , - Thread 2 MJ 6 : 5 ,um min. shall be measured at the pitch diameter ; - T

13、hread MJ 5 : shall show complete coverage, without thickness requirement. l) The strength class of the bolt concerned which can withstand the load at ambient temperature when tested at 100 % load without cracking or breaking of the nut. 2, Maximum test temperature of the parts 3, Published as AECMA

14、standard at the date of publication of the present standard 4) In preparation at the date of publication of the present standard 5, Published as AECMA pre-standard at the date of publication of the present standard Previous page is blank Copyright Association Europeene des Constructeurs de Materiel

15、Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Code OE0 060 070 - - CEN PREN*3020 92 0 3404589 Oil35838 T4b I prEN 3020 Page 4 Values applicable before silver plating. Thread surface will be as achieved by normal

16、 methods of manufacture. 1 ( 7) i Y Radial float in all lines (see table) Form out-of-round in this area I to achieve the self-locking 2 Marking in these areas n requirement. (tooling marks permissible) * Chamfer or radius Y .-.-=-i i v -. - - z-z IT- max. Oll - Remove sharp edges Oll to 0,4 Details

17、 of form not stated are left to the manufacturers discretion. Figure 1 Table 1 Mass Thread D E F K L M N P R S W Radial ku/lOOO O + 0.2 float parts MJ50,8-4ti6H 19 9,s 19- 12 25.2 7 0,6 6.5 2.4 2,5 3 2,54 MJ6xl-4H5H 22 11 22 13,5 29,2 9 MJ7xl-4H5H 26 13 26 16 33,2 10 0,8 8.5 3.2 3.5 . = Designation

18、max. rnax. max. max. nom. - 0,5 min. O . nom. 2 min. -I_ _.- 7,5 3.5 015 - I In accordance with IS0 5855-2. In the self-lockiriu zone, the tolerances apply before formirlu out-of-round. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA

19、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-CEN PREN*3020 92 m 3404569 0031839 982 prEN 3020 Page 5 4 Designation Example : I Description block i Identity block ! EN3020-060 Number of this standard Thread code (see table 11 Note : If necessary, the originator c

20、ode 19005 shall be placed between the description block and the identity block. 5 Marking EN 2424, style N, as indicated on the figure 1 6 Technical specification EN 3004 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-