AECMA PREN 2881-1998 Aerospace Series Nuts Anchor Self-Locking Fuel Resistant Sealing Floating Two Lug With Counterbore in Corrosion Resisting Steel Passivated MoS2 Lubricated Clas.pdf

《AECMA PREN 2881-1998 Aerospace Series Nuts Anchor Self-Locking Fuel Resistant Sealing Floating Two Lug With Counterbore in Corrosion Resisting Steel Passivated MoS2 Lubricated Clas.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 2881-1998 Aerospace Series Nuts Anchor Self-Locking Fuel Resistant Sealing Floating Two Lug With Counterbore in Corrosion Resisting Steel Passivated MoS2 Lubricated Clas.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、- - _ STD-AECMA PREN 2881-ENGL 1778 E LO12311 0034823 b47 AECMA STANDARD prEN 2881 NORME AECMA Edition P 1 AECMA NORM June 1998 Edition approved for publication I 998-06-30 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES (AECMA) Guliedeiie 94 - 8-1200 BRUXELLES - Tel. (+32) 2 775 81 10

2、 - Fax. (+32) 2 775 81 11 Comments should be sent within six months C3 Chairman after the date of publication to Guliedeiie 94 AECMA Mr Arena B-1200 BRUXELLES ICs: 49.030.30 I ENGLISH VERSION Aerospace series Nuts, anchor, self-locking, fuel resistant, sealing, floating, two lug, with counterbore, i

3、n corrosion resisting steel, passivated, Mos2 lubricated Classification: 900 MPa (at ambient temperature) / 120 OC Srie arospatiale crous river, freinage interne, tanches au carburant, flottants, double patte, avec chambrage, en acier rsistant la corrosion, passivs, lubrifis Mos2 Classification : 90

4、0 MPa temprature ambiante) / 120 OC Luft- und Raumfahrt Annietmuttern, selbstsichernd, druckdicht, kraftstoffbestnding, beweglich, beiderseitiger Flansch, mit zylindrischer Aussenkung, aus korrosionsbestndigem Stahl, passiviert, MoS2-geschmiert Klasse: 900 MPa (bei Raumtemperatur) / 120 OC This “Aer

5、ospace Series Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by t

6、he Member countries. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking C

7、entre INPSI and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license

8、 with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 3 prEN 2881 : 1998 I Scope This standard specifies the characteristics of self-locking, fuel resistant, sealing, floating, two lug anchor nuts, with counterbore, in corrosion resisting steel, passivate

9、d, Mos2 lubricated. Classification: 900 MPa 1) / 120 OC 2) 2 Normative references IS0 5855-2 IS0 5858 IS0 8788 IS0 8940 EN 2000 EN 2424 EN 2491 EN 2516 EN 3042 MIL-R-6855 E TR 3791 Aerospace - MJ threads - Part 2: Limit dimensions for bolts and nuts Aerospace - Self-locking nuts with maximum operati

10、ng temperature less than or equal to 425 OC - Procurement specification Aerospace - Fasteners - Tolerances of form and position for nuts Aerospace - Nuts, anchor, self-locking, sealing, floating, two lug, with counterbore, classifications 900 MPa / 120 OC, 900 MPa / 175 OC and 900 MPa / 235 OC - Dim

11、ensions Aerospace series - Quality assurance - EN aerospace products - Approval of the quality systems of manufacturers Aerospace series - Marking of aerospace products Aerospace series - Molybdenum disulphide dry lubricants - Coating methods Aerospace series - Passivation of corrosion resistant ste

12、els and decontamination of nickel base alloys Aerospace series - Quality assurance - EN aerospace products - Qualification procedure Rubber, Synthetic, Sheets, Strips, Molded or Extruded Shapes, General Specification For 3) Aerospace series - Materials for self-locking nuts, threaded inserts and scr

13、ew thread inserts of temperature classes I425 OC 4) 1) Corresponds to the minimum tensile stress which the nut is able to withstand at ambient temperature without breaking or cracking when tested with a bolt of a higher strength class. 2) Maximum temperature that the nut is able to withstand, withou

14、t permanent alteration to its original characteristics, after ambient temperature has been restored. The maximum temperature is conditioned by the seal material. 3) Published by: Department of Defense (DoD), the Pentagon, Washington, D.C. 20301, USA 4) Published as AECMA Technical Report at the date

15、 of publication of this standard Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3 Required characteristics 3.1 See figure 1 and table 1. Configuration

16、 - Dimensions - Masses Dimensions and tolerances are: in conformity with IS0 8940, expressed in millimetres and apply after surface treatment but before Mos2 lubrication. Details of form not stated are at the manufacturers option. 3.2 Tolerances of form and prosition ISO a788 3.3 Materials Cage, sea

17、l retainer and nut element: TR 3791 Sealing ring: rubber, fuel resistant per MIL-R-6855, class 1, grade 60 or equivalent 3.4 Surface treatments Cage and seal retainer: EN 2516 Nut element: EN 2491, thickness not specified, mandatory on threads, optional on other surfaces Copyright Association Europe

18、ene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-AECMA PREN 2882-ENGL 1778 M LOL23LL UUL482b 35b M Page 5 prEN 2881: 1998 Diameter Thread 1) EFGHJKLMQ code min. min. max. max.

19、max. 050 MJ50,8-4H6H 9,5 19 6 3,4 16,2 14,4 24,6 060 MJ6xl-4H5H 11 22 7 19,2 17 29 080 MJ8xl-4H5H 13 26 9 20,3 19,4 32,5 4,l Remove sharp edges 0,l to 0,4. max. max. 7,9 12,5 9,5 16 11,3 18,5 Y-Y W 2) I Form out-of-round in this area to achieve the S + 0,2 O 2,5 3 I L Choice of flange at i manufactu

20、rers discretion W Mass21 max. 14,4 4,3 17,4 7 18,5 10 1 2,8max. IJ 4 1) These values in micrometres apply before surface treatment. They do not apply to threads, punched holes or sheared edges the surface texture of which will be as achieved by usual manufacturing methods. 2) Maximum bolt thread int

21、rusion 3) Minimum radial float of nut element: 0,5 4) Lug thickness at the rivet location Figure 1 Table 1 I 1 ) In accordance with IS0 5855-2. In the self-locking zone the tolerances apply before forming out-of-round. 2) Approximate values (kgll O00 pieces), given for information purposes only Copy

22、right Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-AECMA PREN 2881-ENGL 1778 101231L 0014827 272 Page 6 prEN 2881: 1998 4 Designation EXAMPLE: Description

23、 block Identity block Number of this standard Diameter code (see table 1) NOTE: If necessary, the code 19005 shall be placed between the description block and the identity block. 5 Marking EN 2424, style N. See figure 1. 6 Technical specification IS0 5858, except for: - Approval of manufacturers: see EN 2000; - Qualification of products: see EN 3042. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-