AECMA PREN 2878-1998 Aerospace Series Nuts Anchor Self-Locking Air Resistant Sealing Floating Two Lug With Counterbore in Alloy Steel Cadmium Plated MoS2 Lubricated Classification .pdf

《AECMA PREN 2878-1998 Aerospace Series Nuts Anchor Self-Locking Air Resistant Sealing Floating Two Lug With Counterbore in Alloy Steel Cadmium Plated MoS2 Lubricated Classification .pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 2878-1998 Aerospace Series Nuts Anchor Self-Locking Air Resistant Sealing Floating Two Lug With Counterbore in Alloy Steel Cadmium Plated MoS2 Lubricated Classification .pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AECMA STANDARD NORME AECMA AECMA NORM Edition approved for publication Comments should be sent within six months after the date of oublication to prEN 2878 Edition P 1 June 1998 C3 Chairman PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES (AECMA) Gulledelle 94 - 8-1200 BRUXELLES - Tel.

2、(+32) 2 775 81 1 O - Fax. (32) 2 775 81 11 ICs: 49.030.30 Descriptors: ENGLISH VERSION Aerospace series Nuts, anchor, self-locking, air resistant, sealing, floating, two lug, with counterbore, in alloy steel, cadmium plated, Mos2 lubricated Classification: 900 MPa (at ambient temperature) / 235 OC S

3、rie arospatiale crous river, freinage interne, tanches lair, flottants, double patte, avec chambrage, en acier alli, cadmis, lubrifis Mos2 Classification : 900 MPa ( temprature ambiante) I235 OC Luft- und Raumfahrt Annietmuttern, selbstsichernd, druckdicht, luftbestnding, beweglich, beiderseitiger F

4、lansch, mit zylindrischer Aussenkung, aus legiertem Stahl, verkadmet, MoSz-geschmiert Klasse: 900 MPa (bei Raumtemperatur) / 235 OC This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA (The European Association of Aerospace Industries). It is published on green pap

5、er for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is aff

6、ected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre (NPS) and formal agreement of the Official Services of the Member countries it will be submitted as a draft European Standard to CEN (European Committee

7、 for Standardization) for formal vote. 1998-06-30 AECMA Guiledelie 94 I E-1 200 BRUXELLES I Mr Arena Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1

8、Scope Page 3 prEN 2878: 1998 This standard specifies the characteristics of self-locking, air resistant, sealing, floating, two lug anchor nuts, with counterbore, in alloy steel, cadmium plated, Mos2 lubricated. Classification: 900 MPa 1) / 235 OC 2) 2 Normative references IS0 5855-2 IS0 5858 Aerosp

9、ace - MJ threads - Part 2: Limit dimensions for bolts and nuts Aerospace - Self-locking nuts with maximum operating temperature le equal to 425 OC - Procurement specification Aerospace - Fasteners - Tolerances of form and position for nuts IS0 8788 s than or IS0 8940 EN 2000 EN 2133 EN 2424 EN 2491

10、EN 3042 AMS 3304G TR 3791 Aerospace - Nuts, anchor, self-locking, sealing, floating, two lug, with counterbore, classifications 900 MPa / 120 OC, 900 MPa / 175 OC and 900 MPa / 235 OC - Dimensions Aerospace series - Quality assurance - EN aerospace products - Approval of the quality systems of manuf

11、acturers Aerospace series - Cadmium plating of steels, with maximum specified tensile strength equal to or less than 1 450 MPa, copper, copper alloys and nickel alloys 3) Aerospace series - Marking of aerospace products Aerospace series - Molybdenum disulphide dry lubricants - Coating methods Aerosp

12、ace series - Quality assurance - EN aerospace products - Qualification procedure Silicone Rubber General Purpose 70 Durometer 4) Aerospace series - Materials for self-locking nuts, threaded inserts and screw thread inserts of temperature classes 5 425 OC 5) 1) Corresponds to the minimum tensile stre

13、ss which the nut is able to withstand at ambient temperature without breaking or cracking when tested with a bolt of a higher strength class. 2) Maximum temperature that the nut is able to withstand, without permanent alteration to its original characteristics, after ambient temperature has been res

14、tored. The maximum temperature is conditioned by the cadmium plating. 3) Published as AECMA Standard at the date of publication of this standard 4) Published by: Society of Automotive Engineers, Inc. (SAE), 400 Commonwealth Drive, Warendale, 5) Published as AECMA Technical Report at the date of publ

15、ication of this standard P.A. 15096-0001, USA Previous page is blank Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-LOL23LL OOLqB40 72b Page 4 prEN 28

16、78: 1998 3 Required characteristics 3.1 See figure 1 and table 1. Dimensions and tolerances are: in conformity with IS0 8940, expressed in millimetres and apply after cadmium plating but before Mos2 lubrication. Configuration - Dimensions - Masses Details of form not stated are at the manufacturers

17、option. 3.2 IS0 8788 Tolerances of form and prosition 3.3 Materials Cage, seal retainer and nut element: TR 3791 Sealing ring: rubber, air resistant per AMS 3304 or equivalent 3.4 Surface treatments Cage and seal retainer: EN 2133, 5 pm min. on all surfaces which can be contacted by a 20 mm diameter

18、 ball. On all other surfaces, a continuous deposit shall be present. Nut element: - EN 2133, 5 pm min. on all surfaces which can be contacted by a 20 mm diameter ball. On all other surfaces, a continuous deposit shall be present; - EN 2491 , thickness not specified, mandatory on threads, optional on

19、 other surfaces. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Remove sharp edges 0,l to 0,4. Diameter Thread 1) code 050 MJ50,8-4H6H 060 MJ6x1-4H5H

20、080 MJ8x1-4H5H Y-Y E F G H J K L M Q S W Mass21 min. min. max. max. max. max. max. O max. + 0,2 9,5 19 6 3,4 16,2 14,4 24,6 7,9 12,5 14,4 4,3 2,s 11 22 7 19,2 17 29 9,5 16 17,4 7 13 26 9 20,3 19,4 32,5 11,3 18,5 3 18,5 10 4,1 Choice of flange at manufacturers discretion 2 holes S Page 5 prEN 2878: 1

21、998 1) These values in micrometres apply before surface treatment. They do not apply to threads, punched holes or sheared edges the surface texture of which will be as achieved by usual manufacturing methods. 2) Maximum bolt thread intrusion 3) Minimum radial float of nut element: 0,5 4) Lug thickne

22、ss at the rivet location Figure 1 Table 1 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Page 6 prEN 2878: 1998 4 Designation EXAMPLE: Description blo

23、ck Identity block NUT ENy78-060 Number of this standard Diameter code (see table 1) NOTE: if necessary, the code 19005 shall be placed between the description block and the identity block. 5 Marking EN 2424, style N. See figure 1. 6 Technical specification IS0 5858, except for: - Approval of manufacturers: see EN 2000; - Qualification of products: see EN 3042. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-