AASHTO M 167M M 167-2014 Standard Specification for Corrugated Steel Structural Plate Zinc-Coated for Field-Bolted Pipe Pipe-Arches and Arches.pdf
《AASHTO M 167M M 167-2014 Standard Specification for Corrugated Steel Structural Plate Zinc-Coated for Field-Bolted Pipe Pipe-Arches and Arches.pdf》由会员分享,可在线阅读,更多相关《AASHTO M 167M M 167-2014 Standard Specification for Corrugated Steel Structural Plate Zinc-Coated for Field-Bolted Pipe Pipe-Arches and Arches.pdf(14页珍藏版)》请在麦多课文档分享上搜索。
1、Standard Specification for Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches AASHTO Designation: M 167M/M 167-14 ASTM Designation: A 761/A 761M-04 American Association of State Highway and Transportation Officials 444 North Capitol Street N.W., Suite 249
2、Washington, D.C. 20001TS-4b M 167M/M 167-1 AASHTO Standard Specification for Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches AASHTO Designation: M 167M/M 167-14 ASTM Designation: A 761/A 761M-04 1. SCOPE 1.1. This specification covers corrugated steel s
3、tructural plate, zinc-coated, used in the construction of pipe, pipe-arches, arches, underpasses, and special shapes for field assembly. Appropriate fasteners and accessory materials are also described. The pipe, arches, and other shapes are generally used for drainage purposes, pedestrian and vehic
4、ular underpasses, and utility tunnels. 1.2. This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and plate thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of
5、plate thickness, type of bedding and backfill, manufacture in the plant, and care in the installation. The purchaser must correlate the above factors and also the corrosion and abrasion requirements of the field installation with the plate thickness. The structural design of corrugated steel structu
6、ral plate pipe and the proper installation procedures are described in AASHTO LRFD Bridge Design Specifications, Section 12 and AASHTO LRFD Bridge Construction Specifications, Section 26, respectively. 1.3. The values stated in either SI units or inch-pound units are to be regarded separately as sta
7、ndard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 2. REFERENCED DO
8、CUMENTS 2.1. AASHTO Standards: M 111M/M 111, Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products M 232M/M 232, Zinc Coating (Hot-Dip) on Iron and Steel Hardware T 65M/T 65, Mass Weight of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings T 244, Mechanical Testing of Steel
9、 Products AASHTO LRFD Bridge Design Specifications AASHTO LRFD Bridge Construction Specifications 2.2. ASTM Standards: A 36/A 36M, Standard Specification for Carbon Structural Steel A 307, Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 psi Tensile Strength 2014 by the
10、American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-4b M 167M/M 167-2 AASHTO A 449, Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Us
11、e A 563, Standard Specification for Carbon and Alloy Steel Nuts A 563M, Standard Specification for Carbon and Alloy Steel Nuts Metric A 751, Standard Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products A 754/A 754M, Standard Test Method for Coating Weight (Mass) of Metal
12、lic Coatings on Steel by X-Ray Fluorescence A 780/A 780M, Standard Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings B 6, Standard Specification for Zinc E 29, Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications E 37
13、6, Standard Practice for Measuring Coating Thickness by Magnetic-Field or Eddy-Current (Electromagnetic) Testing Methods F 568M, Standard Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Withdrawn 2012) 2.3. American National Standards: B18.2.1, Square and Hex Bolts and
14、 Screws, Inch Series B18.2.2, Square and Hex Nuts B18.2.3.6M, Bolts, Metric Heavy Hex B18.2.4.6M, Hex Nuts, Heavy, Metric 3. DESCRIPTIONS OF TERMS SPECIFIC TO THIS STANDARD 3.1. archa partial circle shape spanning an open invert between the footings on which it rests. 3.2. box culverta rectangular b
15、ox with a long-radius crown and either short-radius corners or welded corners. It can be with full invert or with footings. 3.3. fabricatorthe producer of the components for the finished product. 3.4. flat platesheet or plate used to fabricate structural plate. 3.5. manufacturerthe producer of the f
16、lat plate and accessories. 3.6. pipea conduit having full circular shape; also, in a general context, all structural shapes covered by this specification. 3.7. pipe-archan arch shape with an approximate semicircular crown, small-radius corners, and large-radius invert. 3.8. pipe, horizontal ellipsea
17、n elliptically shaped pipe with the horizontal diameter approximately 25 percent greater than the nominal diameter. 3.9. pipe, vertically elongatedan elliptically shaped pipe with the vertical diameter up to 10 percent greater than the nominal diameter. 2014 by the American Association of State High
18、way and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.TS-4b M 167M/M 167-3 AASHTO 3.10. purchaserthe purchaser of the finished product. 3.11. special shapea shape, other than described elsewhere in this section, suitable for fabrication with structural pl
19、ate. 3.12. structural platea corrugated and curved plate that is field assembled with other structural plates to form the required structure. 3.13. vehicular underpassa high arch shape with an approximate semicircular crown, large-radius sides, small-radius corners between sides and invert, and larg
20、e-radius invert. 4. ORDERING INFORMATION 4.1. Orders for material under this specification shall include the following information, as necessary, to adequately describe the desired product: 4.1.1. Name of material (corrugated steel structural plate and accessories); 4.1.2. Description of structure (
21、Section 3); 4.1.3. Number of structures; 4.1.4. AASHTO designation and year of issue; 4.1.5. Dimensions of structure (diameter or span and rise, and length, etc.) (Section 8.2 and Note 7); 4.1.6. Thickness of plate (Section 8.1), and for the 150-by-50-mm 6-by-2-in. corrugation, the type of steel in
22、accordance with 5.1.3. and Table 2; 4.1.7. Description of corrugations (Section 6.2); 4.1.8. End treatment (bevel, skew, grade or slope corrections, or other special provision if required by the project plans or specifications); 4.1.9. Seam bolt size and number per corrugation, if different from the
23、 minimums indicated by Tables 3 and 5 (Section 6.3); 4.1.10. Special requirements (including reinforcement locations, shapes, and thicknesses), if required; and 4.1.11. Certification, if required (Section 12.1). Note 1A typical ordering description is as follows: (1) Structural plates and fasteners
24、for two corrugated steel plate pipe-arch, per M 167-_, 180-in. diameter, 0.168-in. plate thickness, 6-by-2-in. corrugations, 140-ft. nominal centerline length with square ends, longitudinal seams with four M20 bolts per corrugation. (2) Structural plates and fasteners for two corrugated steel plate
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AASHTOM167MM1672014STANDARDSPECIFICATIONFORCORRUGATEDSTEELSTRUCTURALPLATEZINCCOATEDFORFIELDBOLTEDPIPEPIPEARCHESANDARCHESPDF

链接地址:http://www.mydoc123.com/p-417676.html