API SPEC 9A-2011 Specification for Wire Rope (TWENTY-SIXTH EDITION ERTA October 2012 ADD 1 November 2016)《金属丝绳规格.第26版.2011年11月1日生效.[代替 API BULL 9-A标准、API REPORT 9A标准、API STD 9A标准]》.pdf
《API SPEC 9A-2011 Specification for Wire Rope (TWENTY-SIXTH EDITION ERTA October 2012 ADD 1 November 2016)《金属丝绳规格.第26版.2011年11月1日生效.[代替 API BULL 9-A标准、API REPORT 9A标准、API STD 9A标准]》.pdf》由会员分享,可在线阅读,更多相关《API SPEC 9A-2011 Specification for Wire Rope (TWENTY-SIXTH EDITION ERTA October 2012 ADD 1 November 2016)《金属丝绳规格.第26版.2011年11月1日生效.[代替 API BULL 9-A标准、API REPORT 9A标准、API STD 9A标准]》.pdf(72页珍藏版)》请在麦多课文档分享上搜索。
1、Specification for Wire RopeAPI SPECIFICATION 9ATWENTY-SIXTH EDITION, MAY 2011EFFECTIVE DATE: NOVEMBER 1, 2011 ERRATA, OCTOBER 2012 REAFFIRMED, APRIL 2016Specification for Wire RopeUpstream SegmentAPI SPECIFICATION 9ATWENTY-SIXTH EDITION, MAY 2011EFFECTIVE DATE: NOVEMBER 1, 2011ERRATA, OCTOBER 2012RE
2、AFFIRMED, APRIL 2016Special NotesAPI publications necessarily address problems of a general nature. With respect to particular circumstances, local,state, and federal laws and regulations should be reviewed.Neither API nor any of APIs employees, subcontractors, consultants, committees, or other assi
3、gnees make anywarranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of theinformation contained herein, or assume any liability or responsibility for any use, or the results of such use, of anyinformation or process disclosed in this publica
4、tion. Neither API nor any of APIs employees, subcontractors,consultants, or other assignees represent that use of this publication would not infringe upon privately owned rights.API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure theaccurac
5、y and reliability of the data contained in them; however, the Institute makes no representation, warranty, orguarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss ordamage resulting from its use or for the violation of any authorities h
6、aving jurisdiction with which this publication mayconflict.API publications are published to facilitate the broad availability of proven, sound engineering and operatingpractices. These publications are not intended to obviate the need for applying sound engineering judgmentregarding when and where
7、these publications should be utilized. The formulation and publication of API publicationsis not intended in any way to inhibit anyone from using any other practices.Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standardis solely responsible f
8、or complying with all the applicable requirements of that standard. API does not represent,warrant, or guarantee that such products do in fact conform to the applicable API standard.All rights reserved. No part of this work may be reproduced, translated, stored in a retrieval system, or transmitted
9、by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005.Copyright 2011 American Petroleum InstituteForewordNothing contained in any API pu
10、blication is to be construed as granting any right, by implication or otherwise, for themanufacture, sale, or use of any method, apparatus, or product covered by letters patent. Neither should anythingcontained in the publication be construed as insuring anyone against liability for infringement of
11、letters patent.This document was produced under API standardization procedures that ensure appropriate notification andparticipation in the developmental process and is designated as an API standard. Questions concerning theinterpretation of the content of this publication or comments and questions
12、concerning the procedures under whichthis publication was developed should be directed in writing to the Director of Standards, American PetroleumInstitute, 1220 L Street, NW, Washington, DC 20005. Requests for permission to reproduce or translate all or any partof the material published herein shou
13、ld also be addressed to the director.Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A one-timeextension of up to two years may be added to this review cycle. Status of the publication can be ascertained from theAPI Standards Department, telepho
14、ne (202) 682-8000. A catalog of API publications and materials is publishedannually by API, 1220 L Street, NW, Washington, DC 20005.Suggested revisions are invited and should be submitted to the Standards Department, API, 1220 L Street, NW,Washington, DC 20005, standardsapi.org.iiiv Contents Page Sp
15、ecial Notes 2 Foreword iii Introduction . vii 1 Scope 1 2 Normative References . 1 3 Terms and Definitions . 2 4 Requirements . 2 4.1 Material . 2 4.2 Rope Manufacture . 3 4.3 Diameter . 5 4.4 Lay Length 6 4.5 Breaking Force. 6 4.6 Length . 8 5 Verification of Requirements and Test Methods 8 5.1 Pro
16、cesses Requiring Validation. 8 5.2 Stranded Ropes and Spiral Ropes 8 5.3 Tests on Well-measuring Wire . 10 5.4 Tests on Well-servicing Strands 10 5.5 Facilities for Witnessing Tests . 10 6 Information for Use . 10 6.1 Certificate . 10 6.2 Packaging and Marking 11 Annex A (normative) Dimensional and
17、Mechanical Properties of Round Wires (Before Rope Fabrication) 12 Annex B (normative) Methods of Wire Testing for Levels 2, 3, 4, and 5 22 Annex C (normative) Tables of Breaking Forces for the More Common Classes, Sizes, and Grades of Stranded Ropes Up to and Including 60 mm Diameter . 24 Annex D (n
18、ormative) Physical Dimensions and Mechanical Properties of Well-servicing Strand . 41 Annex E (informative) Large Diameter Ropes 42 Annex F (normative) Calculation of Minimum Breaking Force for Ropes in Accordance with Annex CRope Grades 1770, 1960, and 2160 . 44 Annex G (normative) Sampling and Acc
19、eptance Criteria for Type Testing of Ropes Produced in Series 46 Annex H (normative) Determination of Breaking Force (Method 1) . 48 Annex I (informative) Tests on Wires from the Rope (if Specified by the Purchaser) . 49 Annex J (informative) Requirements for Bright or Drawn Galvanized Well-measurin
20、g Wire 52 Annex K (informative) Information with Enquiry or Order 53 Annex L (informative) Use of the API Monogram by Licensees . 54 Bibliography 57 vi Figures 1 Method of Measuring Rope Diameter 8 Tables 1 Range of Wire Tensile Strength Grades 2 2 Tolerances on Rope Diameter (Stranded Rope) . 5 3 P
21、ermissible Differences Between Any Two Diameter Measurements . 5 4 Breaking Force Testing Requirements 7 A.1 Permitted Variations in Tensile Strength . 12 A.2 Diameter Tolerances, Minimum Number of Torsions, and Minimum Masses of Zinc for Tensile Strength Grades 1370 N/mm2, 1570 N/mm2, 1770 N/mm2, 1
22、960 N/mm2, and 2160 N/mm2. 13 A.3 Diameter Tolerances for Bright and Drawn Galvanized Wires 15 A.4 Diameter Tolerances for Final Galvanized Wires . 15 A.5 Minimum Breaking Force and Minimum Number of Torsions for Levels 2, 3, 4, and 5 16 A.6 Minimum masses of Zinc for Drawn Galvanized Wire Levels 2,
23、 3, 4, and 5 . 21 A.7 Minimum Masses of Zinc for Final Galvanized Wire Levels 2, 3, 4, and 5 . 21 B.1 Applied Tension for Torsion Tests . 23 C.1 Class 6 7 Fiber Core 25 C.2 Class 6 7 Steel Core 26 C.3 Class 6 19M Fiber Core . 27 C.4 Class 6 19M Steel Core . 28 C.5 Class 6 37M Fiber Core . 29 C.6 Cla
24、ss 6 37M Steel Core . 30 C.7 Class 6 19 Fiber Core 31 C.8 Class 6 19 Steel Core 32 C.9 Class 6 36 Fiber Core 33 C.10 Class 6 36 Steel Core 34 C.11 Class 8 19 Steel Core 35 C.12 Class 8 36 Steel Core 36 C.13 Class 18 7 . 37 C.14 Class 34(M) 7 . 38 C.15 Class 35(W) 7 . 39 C.16 Class 6 V25TS Steel Core
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- APISPEC9A2011SPECIFICATIONFORWIREROPETWENTYSIXTHEDITIONERTAOCTOBER2012ADD1NOVEMBER2016 金属丝 规格 26 2011

链接地址:http://www.mydoc123.com/p-400206.html