BS PD CEN TR 16669-2014 Information technology Device interface to support ISO IEC 18000-3《信息技术 支持ISO IEC 18000-3的设备接口》.pdf

《BS PD CEN TR 16669-2014 Information technology Device interface to support ISO IEC 18000-3《信息技术 支持ISO IEC 18000-3的设备接口》.pdf》由会员分享，可在线阅读，更多相关《BS PD CEN TR 16669-2014 Information technology Device interface to support ISO IEC 18000-3《信息技术 支持ISO IEC 18000-3的设备接口》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication PD CEN/TR 16669:2014 Information technology Device interface to support ISO/IEC 18000-3PD CEN/TR 16669:2014 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of CEN/TR 16669:2014. The UK participation in its preparation was entrusted to T

2、echnical Committee IST/34, Automatic identification and data capture techniques. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its c

3、orrect application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 83894 1 ICS 35.240.60 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy

4、 and Strategy Committee on 30 June 2014. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dPD CEN/TR 16669:2014TECHNICAL REPORT RAPPORT TECHNIQUE TECHNISCHER BERICHT CEN/TR 16669 June 2014 ICS 35.240.60 English Version Information technology - Device interface to support ISO

5、/IEC 18000-3 Technologies de linformation - Interface de prise en charge dISO/CEI 18000-3 pour les appareils Informationstechnik - Gerteschnittstelle zur Untersttzung von ISO/IEC 18000-3 Mode 3 tags This Technical Report was approved by CEN on 20 January 2014. It has been drawn up by the Technical C

6、ommittee CEN/TC 225. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Nether

7、lands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All righ

8、ts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TR 16669:2014 EPD CEN/TR 16669:2014 CEN/TR 16669:2014 (E) 2 Contents Page Foreword 4 Introduction .5 1 Scope 6 2 Normative references 6 3 Terms and definitions .6 4 Symbols and Abbreviations .6

9、5 Executive Summary .7 6 Evaluation privacy protection level of ISO/IEC 18000-3 Mode 3 .7 6.1 General 7 6.2 Technology does not depend on a persistent tag id for air interface communications 8 6.3 Support of standardized access passwords 8 6.3.1 ISO/IEC 18000-3 Mode 3 tags 8 6.3.2 Kill password 9 6.

10、3.3 Access password.9 6.4 Support of the Kill function. .9 6.5 Conclusion .9 7 Industry feedback on the need for the device interface 9 7.1 General 9 7.2 General description of system architecture for Library Management Systems 10 7.3 Feedback on various quotes to justify the development of a device

11、 interface . 11 7.3.1 General . 11 7.3.2 Need for a device interface standard 11 7.3.3 Migration from old to new technology . 11 7.3.4 Inertia associated with any attempt to standardize the device interface 12 7.3.5 Additional security features built into the device interface. 12 7.3.6 Delaying for

12、two years will result in a lost opportunity? 12 7.3.7 Leaving operators to choose between the technologies . 12 7.3.8 Standardized device interface to be incorporated into the PIA? . 12 7.3.9 Conclusion 13 8 Industry feedback on features of the device interface as listed in the scope 13 8.1 General

13、. 13 8.2 Features of the device interface as listed in the scope 13 8.3 GS1/EPCglobal LLRP and ISO/IEC 24791 14 8.4 Conclusion 15 9 Threats through memory content in library RFID tags . 15 9.1 Analysis . 15 9.2 Conclusion 15 Annex A (Informative) Industry representatives . 16 A.1 Libraries . 16 A.1.

14、1 KopGroep Bibliotheken 16 A.1.2 Stadtbibliothek Hannover 16 PD CEN/TR 16669:2014 CEN/TR 16669:2014 (E) 3 A.2 Library RFID System Integrators . 17 A.2.1 Bibliotheca . 17 A.2.2 Nedap 17 A.3 Providers of ISO/IEC 18000-3 readers . 18 A.3.1 Feig . 18 A.3.2 Tagsys Europe . 18 Bibliography 19 PD CEN/TR 16

15、669:2014 CEN/TR 16669:2014 (E) 4 Foreword This document (CEN/TR 16669:2014) has been prepared by Technical Committee CEN/TC 225 “AIDC technologies”, the secretariat of which is held by NEN. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

16、rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This Technical Report is one of a series of related deliverables, which comprise mandate 436 Phase 2. The other deliverables are: EN 16570, Information technology Notification of RFID The informat

17、ion sign and additional information to be provided by operators of RFID application systems EN 16571, Information technology RFID privacy impact assessment process EN 16656, Information technology - Radio frequency identification for item management - RFID Emblem (ISO/IEC 29160:2012, modified) CEN/T

18、R 16684, Information technology Notification of RFID Additional information to be provided by operators CEN/TS 16685, Information technology Notification of RFID The information sign to be displayed in areas where RFID interrogators are deployed CEN/TR 16670, Information technology RFID threat and v

19、ulnerability analysis CEN/TR 16671, Information technology Authorisation of mobile phones when used as RFID interrogators CEN/TR 16672, Information technology Privacy capability features of current RFID technologies CEN/TR 16673, Information technology RFID privacy impact assessment analysis for spe

20、cific sectors CEN/TR 16674, Information technology Analysis of privacy impact assessment methodologies relevant to RFID PD CEN/TR 16669:2014 CEN/TR 16669:2014 (E) 5 Introduction In response to the growing deployment of RFID systems in Europe, the European Commission published in 2007 the Communicati

21、on COM(2007) 96 RFID in Europe: steps towards a policy framework. This Communication proposed steps which needed to be taken to reduce barriers to adoption of RFID whilst respecting the basic legal framework safeguarding fundamental values such as health, environment, data protection, privacy and se

22、curity. In December 2008, the European Commission addressed Mandate M/436 to CEN, CENELEC and ETSI in the field of ICT as applied to RFID systems. The Mandate M/436 was accepted by the ESOs in the first months of 2009. The Mandate addresses the data protection, privacy and information aspects of RFI

23、D, and is being executed in two phases. Phase 1, completed in May 2011, identified the work needed to produce a complete framework of future RFID standards. The Phase 1 results are contained in the ETSI Technical Report TR 187 020, which was published in May 2011. Phase 2 is concerned with the execu

24、tion of the standardisation work programme identified in the first phase. This Technical Report is related to the development of a Technical Specification to define the device interface to support ISO/IEC 18000-3 Mode 3 tags. The proposed Technical Specification on a device interface was intended to

25、 support two high frequency air interface protocols; ISO/IEC 18000-3 mode 1 that has been established and used for 15 years and ISO/IEC 18000-3 mode 3 that is just emerging. The assumption was that ISO/IEC 18000-3 mode 3 would offer greater security and that the protection of the privacy would be be

26、tter served by it. The proposed device interface is intended as a serious attempt to bring greater control to this highly used air interface protocol. In addition, by developing a device interface that supports both air interface protocols, there is the potential to assist in the migration from the

27、older, and (suggested) less secure, technology to a newer and (assumed) more robust technology. Robustness, in this case, is not only of benefit to the operator of the system but also to end users who come into daily contact with the technologies. In the exploration phase to start with the preparati

28、ons for the Technical Specification the project team encountered a challenge to translate the specifics of the required device interface features into practical specifications. First it was not clear why ISO/IEC 18000-3 mode 3 would offer greater security to protect the privacy of the consumers. Sec

29、ond it was not obvious to which “application” the reader should connect and how the proposed device interface would contribute to improving the privacy protection of the consumer. Therefore the project team decided to consult the industry to get their feedback on the proposed standard for a device i

30、nterface. The device interface is aimed at supporting ISO/IEC 18000-3 technology. The Library industry is by far the largest market for the ISO/IEC 18000-3 tags. Therefore this Technical Report will focus on the value that the proposed device could offer to improve the protection of the privacy of t

31、he consumer of the European Library Industry. This Technical Report describes the project teams approach to resolve the challenges. Clause 6 described the evaluation of the privacy protection level of 18000-3 Mode 3. Clause 7 describes the feedback of the industry on the need for the device interfac

32、e. Clause 8 describes the feedback of the industry on features of the device interface as listed in the scope. Clause 9 points to some potential threats caused by some of the memory content in library RFID tags. Annex A contains the list of industry representatives who have contributed to the creati

33、on of this report. Clause 5 draws the conclusions. PD CEN/TR 16669:2014 CEN/TR 16669:2014 (E) 6 1 Scope The scope of this Technical Report is to assess the need to develop a Technical Specification to define an interface that provides RFID system control components with low-level access to RFID inte

34、rrogators for the purpose of optimising RFID data access and control operations. 2 Normative references Not applicable. 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 air interface complete communication link between an Interrogator and a Ta

35、g including the physical layer, collision- arbitration algorithm, command and response structure, and data-coding methodology 3.2 contactless pertaining to the achievement of signal exchange with and supplying power to the card without the use of galvanic elements (i.e., the absence of an ohmic path

36、 from the external interfacing equipment to the integrated circuit(s) contained within the card) 3.3 interrogator (also known as reader) a transmitter/receiver that reads the contents of RFID tags in the vicinity 3.4 RFID tag an electronic identification device that is made up of a chip and antenna

37、4 Symbols and Abbreviations AFI Application family identifier CRC-5 5 bit Cyclic redundancy check CRC-16 16 bit Cyclic redundancy check (calculated on power-up) CRC-16c 16 bit Cyclic redundancy check (calculated in transmission) CW Continuous Wave ERC European Radiocommunications Committee ETSI Euro

38、pean Telecommunications Specifications Institute HF High frequency LMS Library Management System PC Protocol Control RF Radio frequency SRD Short Range Devices PD CEN/TR 16669:2014 CEN/TR 16669:2014 (E) 7 TID Tag-identification or tag identifier, depending on context UHF Ultra High Frequency UID Uni

39、que device IDentifier UII Unique Item Identifier XPC Extended Protocol Control XTID Extended TID indicator (see version 1.3 and above of the EPCglobal TMTag Data Standards) 5 Executive Summary The three “assumed“ security features of ISO/IEC 18000-3 mode 3 do not provide any improvement for the prot

40、ection of the consumers privacy. The differences between ISO/IEC 18000-3 Mode 1 and Mode 3 are on the physical layer and on the memory addressing. Mode 3 in comparison to Mode 1 does not provide any additional feature that could be used to improve consumer privacy. The device interface will not help

41、 to improve the privacy protection of the European citizen. The feedback from the representatives of the European Library Industry in Clause 7 makes clear that the industry sees neither an advantage nor a need for the proposed standard for it will not improve the privacy protection of the citizen in

42、 any way. Besides the fact that the proposed standard will not help to improve the privacy protection of the citizen, the cost of developing and implementing such interface in the existing infrastructure of the RFID Application Software or Library Management Systems would be prohibitive. Therefore C

43、EN/TC 225 Project Team E recommends dropping the development of the proposed device interface standard. 6 Evaluation privacy protection level of ISO/IEC 18000-3 Mode 3 6.1 General The description of Deliverable Task E.4 states: There is one event that might completely change the situation: the intro

44、duction of ISO/IEC 18000-3 Mode 3 air interface protocol and tags. This technology is still in its infancy, but has been developed as the high frequency equivalent of the ISO/IEC 18000-6 Type C technology. It offers higher performance, greater security, and the attributes of medium range reading tha

45、t has proved acceptable for many applications. As examples ISO/IEC 18000-3 Mode 3 offers three features not supported by the established high frequency RFID tags: 1) the technology does not depend on a persistent tag id for air interface communications; 2) it supports standardized access passwords;

46、3) it supports a kill function. This is remarkable, because key difference of ISO/IEC 18000-3 Mode 3 versus ISO/IEC 18000-3 Mode 1 is the speed of reading so that more items could be scanned per second. Mode 3 does not offer any more features that can be used to protect the privacy of the consumer.

47、This clause describes the evaluation if the assumed security features. PD CEN/TR 16669:2014 CEN/TR 16669:2014 (E) 8 6.2 Technology does not depend on a persistent tag id for air interface communications ISO/IEC 18000-3 Mode 1 and ISO/IEC 18000-3 Mode 3 have a different way of collision resolution, b

48、ut in both case the end result is a constant reply that always returns the same number for the tag. Mode 1 tags always return the UID, Mode 3 tags always return the UII. Figure 1 illustrates the interaction between an interrogator and a tag for mode 3 tags. Figure 1 Interaction between interrogator

49、and tag While the UII could be empty for the purpose of the anti-collision the TID memory is defined to contain unique information, where read access cannot be prevented. 6.3 Support of standardized access passwords 6.3.1 ISO/IEC 18000-3 Mode 3 tags ISO/IEC 18000-3 Mode 3 tags do support passwords, but they have no relevance for the protection of the consumers privacy. The memory of a Mode 3 tag is logically separated into four distinct banks, as shown in Figure 2. Figure 2 Memory map of ISO/IEC 18000-3 mode 3 tags PD CEN/T