BS ISO 883-2013 en_3610 Indexable hardmetal (carbide) inserts with rounded corners without fixing hole Dimensions《不带固定孔的带圆角可转位硬性金属(碳化物)镶嵌件.尺寸规格》.pdf

《BS ISO 883-2013 en_3610 Indexable hardmetal (carbide) inserts with rounded corners without fixing hole Dimensions《不带固定孔的带圆角可转位硬性金属(碳化物)镶嵌件.尺寸规格》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 883-2013 en_3610 Indexable hardmetal (carbide) inserts with rounded corners without fixing hole Dimensions《不带固定孔的带圆角可转位硬性金属(碳化物)镶嵌件.尺寸规格》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO 883:2013 Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole DimensionsBS ISO 883:2013 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 883:2013. It supersedes BS 4193-2:1986 which is withdrawn. The

2、UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisio

3、ns of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013 ISBN 978 0 580 81020 6 ICS 25.100.01 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was publis

4、hed under the authority of the Standards Policy and Strategy Committee on 30 September 2013. Amendments issued since publication Date Text affectedBS ISO 883:2013 ISO 2013 Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions Plaquettes amovibles en mtaux-durs (c

5、arbures mtalliques) avec arrondi de pointe, sans trou de fixation Dimensions INTERNATIONAL STANDARD ISO 883 Fourth edition 2013-09-01 Reference number ISO 883:2013(E)BS ISO 883:2013ISO 883:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherw

6、ise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address be

7、low or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 883:2013ISO 883:2013(E) ISO 2013 All rights reserved iii Contents Page F

8、oreword iv 1 Scope . 1 2 Normative references 1 3 Types of insert . 1 4 Interchangeability 1 4.1 Tolerances . 1 4.2 Thickness, s, of inserts with chip breakers . 2 5 Designation and marking 2 5.1 Designation 2 5.2 Marking . 2 6 Measurement . 2 7 Recommended dimensions . 2 7.1 General . 2 7.2 Triangu

9、lar inserts . 3 7.3 Square inserts 4 Annex A (informative) Tolerances for d, m and s . 7 Annex B (informative) Method of measurement of “m” dimension . 8 Annex C (informative) Inserts with rounded corners without fixing hole, with shapes covered by this International Standard 10 Annex D (informative

10、) Relationship between designations in this International Standard and ISO 13399 (all parts) .12 Bibliography .13BS ISO 883:2013ISO 883:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of pr

11、eparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, i

12、n liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/I

13、EC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives Attention is drawn to the possibility that

14、some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent decl

15、arations received. www.iso.org/patents Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. The committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with cutting edges made of hard cuttin

16、g materials. This fourth edition cancels and replaces the third edition (ISO 883:1985), of which it constitutes a minor revision.iv ISO 2013 All rights reservedBS ISO 883:2013INTERNATIONAL ST ANDARD ISO 883:2013(E) Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimen

17、sions 1 Scope This International Standard specifies the dimensions of indexable hardmetal (carbide) inserts with rounded corners, without fixing hole and with normal clearance of 0 and 11. These inserts are primarily intended to be mounted, by top clamping, on turning and boring tools. 2 Normative r

18、eferences The following documents, in whole or in part, are normatively referenced in this document and are indispensable to its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies

19、. ISO 513, Classification and application of hard cutting materials for metal removal with defined cutting edges Designation of the main groups and groups of application ISO 1832, Indexable inserts for cutting tools Designation 3 Types of insert The types of indexable hardmetal (carbide) inserts spe

20、cified in this International Standard are the following: TN: triangular inserts, with 0 normal clearance; TP: triangular inserts, with 11 normal clearance; SN: square inserts, with 0 normal clearance; SP: square inserts, with 11 normal clearance. Inserts with 0 normal clearance (TN and SN) are stand

21、ardized only without chip breakers. Inserts with 11 normal clearance (TP and SP) are provided with and without chip breakers. At the time of publication, neither the shape nor the dimensions of chip breakers are standardized. Thus, if necessary, special features shall be explained by means of a diag

22、ram or additional specifications. Table C.1 gives the ranges of sizes for these inserts. 4 Interchangeability 4.1 Tolerances Indexable hardmetal (carbide) inserts specified in this International Standard are, provided in the following tolerance classes, in accordance with ISO 1832: a) inserts withou

23、t chip breakers: tolerance classes U and G; b) inserts with chip breakers: tolerance class M. Inserts with chip breakers and tolerance class G are second preference (see Annex C). The values of the tolerances in accordance with ISO 1832 are given in Annex A. ISO 2013 All rights reserved 1BS ISO 883:

24、2013ISO 883:2013(E) Other tolerances are given in Tables 1 and 2. 4.2 Thickness, s, of inserts with chip breakers The thickness, s, of inserts with chip breakers is defined as the distance between the cutting edge at the corner and the opposing supporting surface of the insert; see Figure 1 a) and 1

25、 b). a) b) Figure 1 5 Designation and marking 5.1 Designation The designation of the indexable hardmetal (carbide) inserts complying with this International Standard shall conform to ISO 1832. In addition to this designation, one or both of the following may be indicated: the symbol of the group of

26、application, in accordance with ISO 513; the commercial designation of the hardmetal (carbide) grade. 5.2 Marking The following synnbol, at least, shall be marked on the insert itself (except when this would be difficult on the smaller inserts): symbol of the group of application, or commercial desi

27、gnation of the hardmetal (carbide) grade (or both, if possible, on large inserts). 6 Measurement Annex B indicates the methods of measuring the dimension m of the indexable inserts covered by this International Standard. 7 Recommended dimensions 7.1 General The choice of the more common dimensions i

28、s restricted to the specifications given in Tables 1 and 2. It is strongly recommended that these standard inserts be used wherever possible (first preference). When other inserts are specially required, insert dimensions shall be selected from the unshaded 2 ISO 2013 All rights reservedBS ISO 883:2

29、013ISO 883:2013(E) portions/squares (blank cells) of Table C.1 (second preference). Dimensions represented by the shaded portions/squares (shaded cells) of Table C.1 are not recommended. 7.2 Triangular inserts See Figure 2, Figure 3 and Figure 4.TNUN TNGN 0 normal clearance, without chip breakersFig

30、ure 2TPUN TPGN 11 normal clearance, without chip breakersFigure 3 ISO 2013 All rights reserved 3BS ISO 883:2013ISO 883:2013(E)TPMR11 normal clearance, with chip breakersFigure 4 Table 1 Dimensions of triangular inserts Dimensions in millimetres Insert l d a s a m a r 0,10 TNUN 110304 TNGN 110304 TPU

31、N 110304 TPGN 110304 TPMR 110304 11,0 6,35 3,18 9,128 0,4 TNUN 110308 TPUN 110308 TPMR 110308 8,731 0,8 TPUN 160304 TPMR 160304 16,5 9,525 13,891 0,4 TPUN 160308 TPGN 160308 TPMR 160308 13,494 0,8 TPUN 160312 TPGN 160312 TPMR 160312 13,097 1,2 TNUN 160408 TNGN 160408 4,76 13,494 0,8 TNUN 160412 TNGN

32、 160412 13,097 1,2 TPUN 220408 22,0 12,70 18,256 0,8 TNUN 220412 TNGN 220412 TPUN 220412 TPGN 220412 17,859 1,2 TNUN 220416 TPUN 220416 17,463 1,6 a Tolerances in accordance with ISO 1832. See Annex A. 7.3 Square inserts See Figure 5, Figure 6 and Figure 7.4 ISO 2013 All rights reservedBS ISO 883:20

33、13ISO 883:2013(E)SNUN SNGN 0 normal clearance, without chip breakersFigure 5SPUN SPGN 11 normal clearance, without chip breakersFigure 6 ISO 2013 All rights reserved 5BS ISO 883:2013ISO 883:2013(E)SPMR11 normal clearance, with chip breakersFigure 7 Table 2 Dimensions of square inserts Dimensions in

34、millimetres Insert d a b s a m a r 0,10 SNUN 090304 SPUN 090304 SPMR 090304 9,525 3,18 1,808 0,4 SNUN 090308 SNGN 090308 SPUN 090308 SPMR 090308 1,644 0,8 SPUN 120304 SPMR 120304 12,70 2,466 0,4 SPUN 120308 SPGN 120308 SPMR 120308 2,301 0,8 SPUN 120312 SPGN 120312 SPMR 120312 2,137 1,2 SNUN 120408 S

35、NGN 120408 4,76 2,301 0,8 SNUN 120412 SNGN 120412 2,137 1,2 SNUN 150412 15,875 2,795 1,2 SNUN 150416 2,630 1,6 SNUN 190412 19,05 3,452 1,2 SNUN 190416 SPUN 190416 3,288 1,6 a Tolerances in accordance with ISO 1832. See Annex A. b d = l6 ISO 2013 All rights reservedBS ISO 883:2013ISO 883:2013(E) Anne

36、x A (informative) Tolerances for d, m and s NOTE This annex is an extract of ISO 1832. Table A.1 Tolerances for d, m and s a Dimensions in millimetres Insert Tolerance for class U on G on M on Designation d d m d m d m TN. 11. TP . 11. 6,35 0,08 0,13 0,025 0,025 0,05 0,08 TN. 16. TP . 16. SN. 09. SP

37、 . 09. 9,525 0,08 0,13 0,025 0,025 0,05 0,08 TN. 22. TP . 22. SN. 12. SP . 12. 12,70 0,13 0,20 0,025 0,025 0,08 0,13 SN. 15. 15,875 0,18 0,27 0,025 0,025 SN. 19. SP . 19. 19,05 0,18 0,27 0,025 0,025 a Tolerance for s in all tolerance classes: 0,13. ISO 2013 All rights reserved 7BS ISO 883:2013ISO 88

38、3:2013(E) Annex B (informative) Method of measurement of “m” dimension NOTE This annex forms an integral part of this International Standard. B.1 Triangular inserts Dimension m is related to the side opposite the corner that is to be measured. The insert is placed on a surface plate, as shown in Fig

39、ure B.1, and checked by means of a dial gauge zeroed with the aid of a gauge block corresponding to dimension m. The dial gauge then gives a direct reading of the error when applied to the inserts to be measured. Figure B.1 B.2 Square inserts Dimension m is checked by reference to the diameter d of

40、a precision roller, where d corresponds to the nominal diameter of the inscribed circle of the insert. The insert is mounted on a 90 vee-block, as shown in Figure B.2, and checked by means of a dial gauge which has been zeroed to dimension m by means of a roller with the aid of a gauge block. The di

41、al gauge then gives a direct reading of the error when applied to the inserts to be measured. The roller has a tolerance of 0,002 mm.8 ISO 2013 All rights reservedBS ISO 883:2013ISO 883:2013(E) Figure B.2 ISO 2013 All rights reserved 9BS ISO 883:2013ISO 883:2013(E) Annex C (informative) Inserts with

42、 rounded corners without fixing hole, with shapes covered by this International Standard Table C.1 Range of sizes10 ISO 2013 All rights reservedBS ISO 883:2013ISO 883:2013(E) d Normal clearance Tolerance class UGM Insert without chip breakers (N)w ithout chip breakers (N)w ith chip breakers on the f

43、ace (R)w ith chip breakers on the face (R) Designation r Designation r Designation r Designation r 6,35 TNUN 1103 TNGN 1103 9,525 TNUN 1603 TNGN 1603 TNUN 1604 TNGN 1604 12,7 TNUN 2204 TNGN 2204 6,35 TPUN 1103 TPGN 1103 TPGR 1103 TPMR 1103 9,525T PUN 1603 TPGN 1603 TPGR 1603 TPMR 1603 12,7 TPUN 2204

44、 TPGN 2204 TPGR 2204 TPMR 2204 9,525 SNUN 0903 SNGN 0903 12,7 SNUN 1203 SNGN 1203 SNUN 1204 SNGN 1204 15,875 SNUN 1504 SNGN 1504 19,05S NUN 1904 SNGN 1904 9,525 SPUN 0903 SPGN 0903 SPGR 0903 SPMR 0903 12,7 SPUN 1203 SPGN 1203 SPGR 1203 SPMR 1203 15,875 SPUN 1504 SPGN 1504 SPGR 1504 SPMR 1504 19,05S

45、PUN 1904 SPGN 1904 SPGR 1904 SPMR 1904 : ;v y :mm ISO 2013 All rights reserved 11BS ISO 883:2013ISO 883:2013(E) Annex D (informative) Relationship between designations in this International Standard and ISO 13399 (all parts) For the relationship between designations in this International Standard an

46、d preferred symbols according to ISO 13399 (all parts), see Table A.1. Table D.1 Relationship between designations in this International Standard and the ISO 13399 series Symbol in ISO 883 (this International Standard) Reference in ISO 883 (this Interna- tional Standard) Property name the ISO 13399

47、series Symbol the ISO 13399 series Reference the ISO 13399 series d 7.2, Table 1 7.3, Table 2 Inscribed circle diam- eter IC ISO/TS 13399-2 71CE7A96D9F7D l 7.2, Table 1 7.3, Table 2 Cutting edge length L ISO/TS 13399-2 71DD6C95DA49B m 7.2, Table 1 7.3, Table 2 m-dimension M ISO/TS 13399-2 71CE7AA0972DB r 7.2, Table 1 7.3, Table 2 Corner radius RE ISO/TS 13399-2 71DD6C8ACA503 s 4.2 7.2, Table 1 7.3, Table 2 Insert thickness S ISO/TS 13399-2 71CE7A9F5308C12 ISO 2013 All rights reservedBS ISO 883:2013ISO 883:2013(E) Bibliography 1 ISO 13399 (all parts