BS ISO 7425-1-2002 en_9124 Hydraulic fluid power - Housing for elastomer-energized plastic-faced seals - Dimensions and tolerances - Piston seal housings《液压流体动力.弹性体塑料面密封件的汽缸.尺寸和公差.活塞密封汽缸》.pdf

《BS ISO 7425-1-2002 en_9124 Hydraulic fluid power - Housing for elastomer-energized plastic-faced seals - Dimensions and tolerances - Piston seal housings《液压流体动力.弹性体塑料面密封件的汽缸.尺寸和公差.活塞密封汽缸》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 7425-1-2002 en_9124 Hydraulic fluid power - Housing for elastomer-energized plastic-faced seals - Dimensions and tolerances - Piston seal housings《液压流体动力.弹性体塑料面密封件的汽缸.尺寸和公差.活塞密封汽缸》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 7425-1:1988 Hydraulic fluid power Housing for elastomer-energized, plastic-faced seals Dimensions and tolerances Part 1: Piston seal housings ICS 23.100.99 BS ISO 7425-1:1988 This British Standard, having been prepared under the direction of the Engineering Sector Policy and

2、Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 28 August 2002 BSI 28 August 2002 ISBN 0 580 40301 7 National foreword This British Standard reproduces verbatim ISO 7425-1:1988 and implements it as the UK national standard. Together with BS ISO

3、 7425-2:1989 it supersedes BS 6984:1988 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MCE/11, Fluid seals and housings, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretar

4、y. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of Briti

5、sh Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present

6、 to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an ins

7、ide front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 5, the National Annex NA page, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comme

8、ntsINTERNATIONAL STANDARD INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION MEXjJYHAPOAHAfl OPI-AHM3AMR fl0 CTAHAPTM3AMM Hydraulic fluid power - Housings for elastomer- energized, plastic-faced Seals - Dimensions and tolerantes - Part 1 I Piston seal housing

9、s Transmissions hydrauliques - Logements pour joints en however, consul- tation with the manufacturer is recommended when making the appropriate selection. The requirements for the surface finish of the components in contact with the seal are dependent on the application and its life requirement and

10、 should be subject to agreement between the purchaser and seal manufacturer. 9 Lead-in chamfer 6 Dimensions and tolerantes Seal housing dimensions and tolerantes shall be selected from table 2. 9.1 To protect the seal from darnage during assembly, lead-in chamfers are required, either as an integral

11、 patt of housing components or on separate assembly tools. 7 Extrusion gap 9.2 Reference shall be made to figure 1 for typical location of lead-in chamfers when these are part of the housing compo- nent. The extrusion gap (D - d3; see figure 1) is determined by the bore diameter and adjacent metal c

12、omponents on either side of the Seal. 9.3 The minimum axial length of lead-in chamfers, whether on housing components or assembly tools, is given in table 1. Table 1 - Lead-in chamfer Dimensions in millimetres Radial depth of seal housing, S nom. Minimum axial length of lead-in chamfer, C 5 7,5 10 1

13、2,25 2,5 3,75 15 20 5,5 7,75 IO,5 12,5 1,5 2 2,5 4 5 65 7,5 10 Figure 1 - Example of Piston seal housing 2 BSISO74251:1988OSI 1-5247 8891: IE( Table 2 - Dimensions and tolerantes of seal housings Dimensions in millimetres Bore diameter) Radial depth D s H92) , nom. Groove diameter Axial length d 4 L

14、2 (without back-up rings) (with back-up rings) h92) + 0,2 +0,2 0 0 2,5 11 16 22 3,75 8,5 3,2 20 23 15 22 - 3,75 12,5 3,2 3,75 175 3,2 25 5,5 14 4,2 5 15 5 8 3,75 24,5 3,2 - 32 5,5 21 4,2 I 5 I 22 I 5 I 8 0,5 40 3,75 32,5 3,2 - 5,5 29 4,2 I 5 I 30 I 5 l 8 5,5 39 4,2 - 50 7,75 34,5 6,3 7,5 35 715 12,5

15、 5,5 52 4,2 - 63 7,75 47,5 6,3 7,5 48 7,5 12,5 r max. 515 69 4,2 - 80 7,75 64,5 6,3 10 60 10 16 - 5,5 89 4,2 - 100 7,75 8415 613 10 80 10 16 7,75 109,5 613 - 125 IO,5 104 8,1 10 105 10 16 7,75 144,5 613 - 160 IO,5 139 Kl 12,5 135 12,5 20 7,75 184,5 63 - 200 IO,5 179 8,1 12,5 175 12,5 20 IO,5 229 81

16、- 250 12,25 225,5 kl 15 220 15 25 IO,5 299 811 - 320 12,25 295,5 8,1 15 290 15 25 12,25 375,5 8,1 - 15 370 12,5 20 360 20 32 12,25 475,5 8,1 - 500 15 470 12,5 20 460 20 32 03 1) Bore diameters in accordance with ISO 3320. 2) See ISO 286-2. BSISO74251:1988OSI 45247 : 8891 IE( 10 Identification Statem

17、ent (Reference to this part of ISO 7425) “Piston seal housing for elastomer-energized, plastic-faced Seals selected in accordance with ISO 7425-1, Hydraulic fluid power - Housings for elastomer-energized, plastic- faced Seals Use the following statement in test reports, catalogues and sales Iiteratu

18、re when electing to comply with this part of ISO 7425: - Dimensions and tolerantes - Part 1: Piston sealhousings.” BSISO74251:1988OSI 1-5247 8891: IE( Annex A (informative) Bibliography ISO 468 : 1982, Surface roughness - Parameters, their values and general rules for specifying reguirements. ISO 43

19、94-1 : 1980, Fluid power Systems and components - Cylinder barrels - Part 7: Requirements for steel tubes with specia/y finished bores. BSISO74251:19881) BS 1134-1:1998 Assessment of surface texture Part 1: Methods and instrumentation 2) BS 5242-1:1987 Tubes for fluid power cylinder barrels Part 1:

20、Specification for steel tubes with specially finished surfaces 3)BS 5242-2:1983, ISO 6537:1982 Tubes for fluid power cylinder barrels Part 2: Specification for non-ferrous metallic tubes with specially finished bores National Annex NA (informative) Recommendations for surface texture NA.1 The surfac

21、e texture of components which are in sliding contact with the seal should be 0.1 m to 0.4 m Ra and 1.6 m Rz max., when measured in accordance with BS 1134-1 1) . NA.2 The surface texture of components which are in static contact with the seal should be 0.4 m to 1.6 m Ra and 6.3 m Rz max., when measu

22、red in accordance with BS 1134-1. NOTE Exceptional service conditions may necessitate the selection of other grades of surface texture; reference should be made to BS 5242-1 2)for steel and BS 5242-2 3) for non-ferrous tubes. BSISO74251:1988sihT egap yllanoitnetni tfel knalb BS ISO 7425-1:1988 BSI 3

23、89 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are

24、updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Bri

25、tish Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automaticall

26、y receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http

27、:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and internation

28、al standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subsc

29、ribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Informatio

30、n regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publicatio

31、ns of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permissio

32、n from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.