EN ISO 4545-4-2018 Metallic materials - Knoop hardness test - Part 4 Table of hardness values.pdf

《EN ISO 4545-4-2018 Metallic materials - Knoop hardness test - Part 4 Table of hardness values.pdf》由会员分享，可在线阅读，更多相关《EN ISO 4545-4-2018 Metallic materials - Knoop hardness test - Part 4 Table of hardness values.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Metallic materials - Knoop hardness testPart 4: Table of hardness values (ISO 4545-4:2017)BS EN ISO 4545-4:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4545-4 February 2018 ICS 77.040.10 Supersedes EN IS

2、O 4545-4:2005English Version Metallic materials - Knoop hardness test - Part 4: Table of hardness values (ISO 4545-4:2017) Matriaux mtalliques - Essai de duret Knoop - Partie 4: Tableau des valeurs de duret (ISO 4545-4:2017) Metallische Werkstoffe - Hrteprfung nach Knoop - Teil 4: Tabelle zur Bestim

3、mung der Hrtewerte (ISO 4545-4:2017) This European Standard was approved by CEN on 1 January 2018. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-t

4、o-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by transla

5、tion under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland,

6、 Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDI

7、ZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4545-4:2018 ENational forewordThis B

8、ritish Standard is the UK implementation of EN ISO 4545-4:2018. It is identical to ISO 4545-4:2017. It supersedes BS EN ISO 4545-4:2005, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/101/5, Indentation hardness testing.A list of organizations rep

9、resented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0

10、580 84283 2ICS 77.040.10Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH ST

11、ANDARDBS EN ISO 4545-4:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 4545-4 February 2018 ICS 77.040.10 Supersedes EN ISO 4545-4:2005English Version Metallic materials - Knoop hardness test - Part 4: Table of hardness values (ISO 4545-4:2017) Matriaux mtalliques - Essai de duret Knoop

12、 - Partie 4: Tableau des valeurs de duret (ISO 4545-4:2017) Metallische Werkstoffe - Hrteprfung nach Knoop - Teil 4: Tabelle zur Bestimmung der Hrtewerte (ISO 4545-4:2017) This European Standard was approved by CEN on 1 January 2018. CEN members are bound to comply with the CEN/CENELEC Internal Regu

13、lations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN memb

14、er. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. C

15、EN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

16、 Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of expl

17、oitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 4545-4:2018 EBS EN ISO 4545-4:2018EN ISO 4545-4:2018 (E) 3 European foreword This document (EN ISO 4545-4:2018) has been prepared by Technical Committee ISO/TC 164 “Mechanical testing of metals” in col

18、laboration with Technical Committee ECISS/TC 101 “Test methods for steel (other than chemical analysis)” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by

19、August 2018, and conflicting national standards shall be withdrawn at the latest by August 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This

20、 document supersedes EN ISO 4545-4:2005. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yu

21、goslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 454

22、5-4:2017 has been approved by CEN as EN ISO 4545-4:2018 without any modification. BS EN ISO 4545-4:2018ISO 4545-4:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Table of Knoop hardness values . 1 ISO 2017 All rights reserved iiiContents PageBS EN ISO 4545-4:2018ISO

23、 4545-4:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject

24、 for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC)

25、on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be note

26、d. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying a

27、ny or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of u

28、sers and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barri

29、ers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.This document was prepared by Technical Committee ISO/TC 164, Mechanical testing of metals, Subcommittee SC 3, Hardness testing.This second edition cancels and replaces the first edition (ISO 4545-4:2005), which has been technic

30、ally revised.The main changes compared to the previous edition are as follows: in Table 1, the data for indentations using forces 0,009 807 N (HK 0,001), 0,019 61 N (HK 0,002), 0,049 03 N (HK 0,005) and 19,613 N (HK 2) have been added; the calculation clause has been removed.A list of all parts in t

31、he ISO 4545 series can be found on the ISO website.iv ISO 2017 All rights reservedBS EN ISO 4545-4:2018INTERNATIONAL STANDARD ISO 4545-4:2017(E)Metallic materials Knoop hardness test Part 4: Table of hardness values1 ScopeThis document gives a table for the calculation of Knoop hardness values for u

32、se in tests carried out in accordance with ISO 4545-1.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the

33、 latest edition of the referenced document (including any amendments) applies.ISO 4545-1, Metallic materials Knoop hardness test Part 1: Test method3 Terms and definitionsNo terms and definitions are listed in this document.ISO and IEC maintain terminological databases for use in standardization at

34、the following addresses: ISO Online browsing platform: available at http:/www.iso.org/obp IEC Electropedia: available at http:/www.electropedia.org/4 Table of Knoop hardness valuesThe values given in Table 1 were calculated from the Knoop hardness formula in accordance with ISO 4545-1. ISO 2017 All

35、rights reserved 1BS EN ISO 4545-4:2018ISO 4545-4:2017(E)Table 1 Knoop hardness valuesIndentation diagonal d mmTest force N0,009 8070,019 610,049 030,098 070,196 130,245 170,490 330,980 71,961 3 2,942 0 4,903 3 9,807 19,613Knoop hardnessHK HK HK HK HK HK HK HK HK HK HK HK HK0,001 0,002 0,005 0,01 0,0

36、2 0,025 0,05 0,1 0,2 0,3 0,5 1 20,020 0 35,57 71,14 177,9 355,7 711,4 889,3 1 779 3 557 0,020 2 34,87 69,74 174,4 348,7 697,4 871,8 1 744 3 487 0,020 4 34,19 68,38 171,0 341,9 683,8 854,8 1 710 3 419 0,020 6 33,53 67,06 167,7 335,3 670,6 838,3 1 677 3 353 0,020 8 32,89 65,78 164,4 328,9 657,8 822,2

37、1 644 3 289 0,021 0 32,26 64,53 161,3 322,6 645,3 806,6 1 613 3 226 0,021 2 31,66 63,32 158,3 316,6 633,2 791,5 1 583 3 166 0,021 4 31,07 62,14 155,3 310,7 621,4 776,7 1 553 3 107 0,021 6 30,50 60,99 152,5 305,0 609,9 762,4 1 525 3 050 0,021 8 29,94 59,88 149,7 299,4 598,8 748,5 1 497 2 994 0,022 0

38、29,40 58,80 147,0 294,0 588,0 735,0 1 470 2 940 0,022 2 28,87 57,74 144,4 288,7 577,4 721,8 1 444 2 887 0,022 4 28,36 56,72 141,8 283,6 567,2 708,9 1 418 2 836 0,022 6 27,86 55,72 139,3 278,6 557,2 696,5 1 393 2 786 0,022 8 27, 37 54,74 136,9 273,7 547,4 684,3 1 369 2 737 0,023 0 26,90 53,80 134,5 2

39、69,0 538,0 672,4 1 345 2 690 0,023 2 26,44 52,87 132,2 264,4 528,7 660,9 1 322 2 644 0,023 4 25,99 51,97 129,9 259,9 519,7 649,6 1 299 2 599 0,023 6 25,55 51,09 127,7 255,5 510,9 638,7 1 277 2 555 0,023 8 25,12 50,24 125,6 251,2 502,4 628,0 1 256 2 512 0,024 0 24,70 49,41 123,5 247,0 494,1 617,6 1 2

40、35 2 470 0,024 2 24,30 48,59 121,5 243,0 485,9 607,4 1 215 2 430 0,024 4 23,90 47,80 119,5 239,0 478,0 597, 5 1 195 2 390 0,024 6 23,51 47,02 117,6 235,1 470,2 587,8 1 176 2 351 0,024 8 23,13 46,27 115,7 231,3 462,7 578,4 1 157 2 313 0,025 0 22,77 45,53 113,8 227,7 455,3 569,2 1 138 2 277 0,025 2 22

41、,41 44,81 112,0 224,1 448,1 560,2 1 120 2 241 0,025 4 22,05 44,11 110,3 220,5 441,1 551,4 1 103 2 205 0,025 6 21,71 43,42 108,6 217,1 434,2 542,8 1 086 2 171 0,025 8 21,38 42,75 106,9 213,8 427, 5 534,4 1 069 2 138 0,026 0 21,05 42,10 105,2 210,5 421,0 526,2 1 052 2 105 0,026 2 20,73 41,46 103,6 207

42、, 3 414,6 518,2 1 036 2 073 0,026 4 20,42 40,83 102,1 204,2 408,3 510,4 1 021 2 042 0,026 6 20,11 40,22 100,5 201,1 402,2 502,7 1 005 2 011 0,026 8 19,81 39,62 99,05 198,1 396,2 495,3 990,5 1 981 3 962 2 ISO 2017 All rights reservedBS EN ISO 4545-4:2018ISO 4545-4:2017(E)Indentation diagonal d mmTest

43、 force N0,009 8070,019 610,049 030,098 070,196 130,245 170,490 330,980 71,961 3 2,942 0 4,903 3 9,807 19,613Knoop hardnessHK HK HK HK HK HK HK HK HK HK HK HK HK0,001 0,002 0,005 0,01 0,02 0,025 0,05 0,1 0,2 0,3 0,5 1 20,027 0 19,52 39,04 97, 59 195,2 390,4 488,0 975,9 1 952 3 904 0,027 2 19,23 38,46

44、 96,16 192,3 384,6 480,8 961,6 1 923 3 846 0,027 4 18,95 37,91 94,76 189,5 379,1 473,8 947,6 1 895 3 791 0,027 6 18,68 37,36 93,39 186,8 373,6 467,0 933,9 1 868 3 736 0,027 8 18,41 36,82 92,06 184,1 368,2 460,3 920,6 1 841 3 682 0,028 0 18,15 36,30 90,74 181,5 363,0 453,7 907,4 1 815 3 630 0,028 2 1

45、7,89 35,78 89,46 178,9 357,8 4 47, 3 894,6 1 789 3 578 0,028 4 17,64 35,28 88,21 176,4 352,8 441,0 882,1 1 764 3 528 0,028 6 17,40 34,79 86,98 174,0 347,9 434,9 869,8 1 740 3 479 0,028 8 17,15 34,31 85,77 171,5 343,1 428,9 857,7 1 715 3 431 0,029 0 16,92 33,84 84,59 169,2 338,4 423,0 845,9 1 692 3 3

46、84 0,029 2 16,69 33,38 83,44 166,9 333,8 417,2 834,4 1 669 3 338 0,029 4 16,46 32,92 82,31 164,6 329,2 411,5 823,1 1 646 3 292 0,029 6 16,24 32,48 81,20 162,4 324,8 406,0 812,0 1 624 3 248 0,029 8 16,02 32,05 80,11 160,2 320,5 400,6 801,1 1 602 3 205 0,030 0 15,81 31,62 79,05 158,1 316,2 395,2 790,5

47、 1 581 3 1620,030 2 15,60 31,20 78,01 156,0 312,0 390,0 780,1 1 560 3 1200,030 4 15,40 30,79 76,98 154,0 307,9 384,9 769,8 1 540 3 0790,030 6 15,20 30,39 75,98 152,0 303,9 379,9 759,8 1 520 3 0390,030 8 15,00 30,00 75,00 150,0 300,0 375,0 750,0 1 500 3 0000,031 0 14,81 29,61 74,03 148,1 296,1 370,2

48、740,3 1 481 2 9610,031 2 14,62 29,23 73,09 146,2 292,3 365,4 730,9 1 462 2 9230,031 4 14,43 28,86 72,16 144,3 288,6 360,8 721,6 1 443 2 8860,031 6 14,25 28,50 71,25 142,5 285,0 356,2 712,5 1 425 2 8500,031 8 14,07 28,14 70,35 140,7 281,4 351,8 703,5 1 407 2 8140,032 0 13,90 27,79 69,48 139,0 277,9 3

49、47,4 694,8 1 390 2 7790,032 2 13,72 27,45 68,62 137, 2 274,5 343,1 686,2 1 372 2 7450,032 4 13,55 27,11 67,77 135,5 271,1 338,9 677,7 1 355 2 7110,032 6 13,39 26,78 66,94 133,9 267,8 334,7 669,4 1 339 2 6780,032 8 13,23 26,45 66,13 132,3 264,5 330,6 661,3 1 323 2 645 3 9680,033 0 13,07 26,13 65,33 130,7 261,3 326,6 653,3 1 307 2 613 3 9200,033 2 12,91 25,82 64,54 129,1 258,2 322,7 645,4 1 291 2 582 3 8730,033 4 12,75 25,51 63,77 127,