EN IEC 62282-5-100-2018 Fuel cell technologies - ParT 5-100 Portable fuel cell power systems - Safety.pdf

《EN IEC 62282-5-100-2018 Fuel cell technologies - ParT 5-100 Portable fuel cell power systems - Safety.pdf》由会员分享，可在线阅读，更多相关《EN IEC 62282-5-100-2018 Fuel cell technologies - ParT 5-100 Portable fuel cell power systems - Safety.pdf（68页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Fuel cell technologiesPart 5-100: Portable fuel cell power systems Safety (IEC 62282-5-100:2018)BS EN IEC 62282-5-100:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 62282-5-100 August 2018 ICS 27.070 Super

2、sedes EN 62282-5-1:2012 English Version Fuel cell technologies - Part 5-100: Portable fuel cell power systems - Safety (IEC 62282-5-100:2018) Technologies des piles combustible - Partie 5-100: Systmes piles combustible portables - Scurit (IEC 62282-5-100:2018) Brennstoffzellentechnologien - Teil 5-1

3、00: Portable Brennstoffzellen-Energiesysteme - Sicherheit (IEC 62282-5-100:2018) This European Standard was approved by CENELEC on 2018-05-17. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of

4、a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, Germ

5、an). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium

6、, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, S

7、weden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of

8、exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 62282-5-100:2018 E National forewordThis British Standard is the UK implementation of EN IEC 622825100:2018. It is identical to IEC 622825100:2018. It supersedes BS EN 6228251:2012, which is withdrawn.The U

9、K participation in its preparation was entrusted to Technical Committee GEL/105, Fuel cell technologies.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are

10、 responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 96966 9ICS 27.070Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Stan

11、dards Policy and Strategy Committee on 31 August 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN IEC 622825100:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IEC 62282-5-100 August 2018 ICS 27.070 Supersedes EN 62282-5-1:2012 English Version Fuel

12、cell technologies - Part 5-100: Portable fuel cell power systems - Safety (IEC 62282-5-100:2018) Technologies des piles combustible - Partie 5-100: Systmes piles combustible portables - Scurit (IEC 62282-5-100:2018) Brennstoffzellentechnologien - Teil 5-100: Portable Brennstoffzellen-Energiesysteme

13、- Sicherheit (IEC 62282-5-100:2018) This European Standard was approved by CENELEC on 2018-05-17. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. U

14、p-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by

15、translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republ

16、ic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kin

17、gdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CENELEC All rights of exploitation in any form and by any means res

18、erved worldwide for CENELEC Members. Ref. No. EN 62282-5-100:2018 E BS EN IEC 622825100:2018EN IEC 62282-5-100:2018 (E) 2 European foreword The text of document 105/649/CDV, future edition 1 of IEC 62282-5-100, prepared by IEC/TC 105 “Fuel cell technologies“ was submitted to the IEC-CENELEC parallel

19、 vote and approved by CENELEC as EN IEC 62282-5-100:2018. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2019-02-17 latest date by which the national standards conflicti

20、ng with the document have to be withdrawn (dow) 2021-05-17 This document supersedes EN 62282-5-1:2012 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such

21、 patent rights. Endorsement notice The text of the International Standard IEC 62282-5-100:2018 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60079 series NOTE H

22、armonized as EN IEC 60079 series IEC 60079-0 NOTE Harmonized as EN IEC 60079-0 ISO/IEC 80079-20-1 NOTE Harmonized as FprEN ISO 80079-20-11IEC 60079-32 series NOTE Harmonized as EN 60079-32 series IEC 60664-1 NOTE Harmonized as EN 60664-1 IEC 60730 series NOTE Harmonized as EN 60730 series IEC 61140

23、NOTE Harmonized as EN 61140 IEC 61439-1 NOTE Harmonized as EN 61439-1 ISO 4080 NOTE Harmonized as EN ISO 4080 ISO 15156-1 NOTE Harmonized as EN ISO 15156-1 IEC 62282-6-100 NOTE Harmonized as EN 62282-6-100 1To be published. BS EN IEC 622825100:2018EN IEC 62282-5-100:2018 (E) 3 Annex ZA (normative) N

24、ormative references to international publications with their corresponding European publications The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For un

25、dated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European

26、 Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60034 series Rotating electrical machines - - IEC 60068-2-75 - Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests EN 60068-2-75 - IEC 60079-2 - Explosive atmospheres - Part 2: Equip

27、ment protection by pressurized enclosure “p“ EN 60079-2 - IEC 60079-10 series Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres EN 60079-10 series IEC 60079-15 - Explosive atmospheres - Part 15: Equipment protection by type of protection “n“ EN IEC 60079-15 - IEC

28、 60079-29 series Explosive atmospheres - Part 29-1: Gas detectors - Performance requirements of detectors for flammable gases EN 60079-29 series IEC 60086-4 - Primary batteries - Part 4: Safety of lithium batteries EN 60086-4 - IEC 60204-1 (mod) 2016 Safety of machinery - Electrical equipment of mac

29、hines - Part 1: General requirements EN 60204-1 2018 IEC 60216-4-1 - Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber ovens EN 60216-4-1 - IEC 60335-1 (mod) 2010 Household and similar electrical appliances - Safety - Part 1: General requirement

30、s EN 60335-1 2012 + A1 2013 + A2 2016 - - + A11 2014 - - + AC 2014 - - + A13 2017 IEC 60364-4-41 - Low-voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock HD 60364-4-41 - IEC 60529 - Degrees of protection provided by enclosures (IP Code) - - IEC 60

31、695-2-11 - Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) EN 60695-2-11 - BS EN IEC 622825100:2018EN IEC 62282-5-100:2018 (E) 4 IEC 60695-2-13 - Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods -

32、Glow-wire ignition temperature (GWIT) test method for materials EN 60695-2-13 - IEC 60695-11-5 - Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance EN 60695-11-5 - IEC 60695-11-10 - Fire hazard testing - Part 11-10: Test fl

33、ames - 50 W horizontal and vertical flame test methods EN 60695-11-10 - IEC 60695-11-20 - Fire hazard testing - Part 11-20: Test flames - 500 W flame test method EN 60695-11-20 - IEC 60730-1 (mod) 2013 Automatic electrical controls - Part 1: General requirements EN 60730-1 2016 + A1 2015 + A1 2016 I

34、EC 60730-2-5 - Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems EN 60730-2-5 - IEC 60730-2-17 - Automatic electrical controls for household and similar use - Part 2-17: Particular requirements for electrically operated gas valves, incl

35、uding mechanical requirements - - IEC 60812 - Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) EN 60812 - IEC 60884-1 - Plugs and socket-outlets for household and similar purposes - Part 1: General requirements - - IEC 60934 - Circuit-breakers for e

36、quipment (CBE) EN 60934 - IEC 60950-1 (mod) 2005 Information technology equipment - Safety - Part 1: General requirements EN 60950-1 2006 - - + A11 2009 + A1 (mod) 2009 + A1 2010 - - + A12 2011 - - + AC 2011 + A2 (mod) 2013 + A2 2013 IEC 60990 2016 Methods of measurement of touch current and protect

37、ive conductor current EN 60990 2016 IEC 61000-3-2 - Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions (equipment input current 16 A per phase) EN IEC 61000-3-2 - IEC 61000-3-3 - Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltag

38、e changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current 16 A per phase and not subject to conditional connection EN 61000-3-3 - IEC 61000-6-1 - Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity standard for residen

39、tial, commercial and light-industrial environments EN 61000-6-1 - IEC 61000-6-2 - Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments EN 61000-6-2 - IEC 61000-6-3 - Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emiss

40、ion standard for residential, commercial and light-industrial environments EN 61000-6-3 - BS EN IEC 622825100:2018EN IEC 62282-5-100:2018 (E) 5 IEC 61000-6-4 - Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments EN IEC 61000-6-4 - IEC 610

41、25 - Fault Tree Analysis (FTA) EN 61025 - IEC 61032 - Protection of persons and equipment by enclosures - Probes for verification EN 61032 - IEC 61508-1 - Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements EN 61508-1 - IEC 61511-1

42、 - Functional safety - Safety instrumented systems for the process industry sector - Part 1: Framework, definitions, system, hardware and application programming requirements EN 61511-1 - IEC 61511-3 - Functional safety - Safety instrumented systems for the process industry sector - Part 3: Guidance

43、 for the determination of the required safety integrity levels EN 61511-3 - IEC 61882 - Hazard and operability studies (HAZOP studies) - Application guide EN 61882 - IEC 62040-1 - Uninterruptible power systems (UPS) - Part 1: Safety requirements - - IEC 62040-2 - Uninterruptible power systems (UPS)

44、- Part 2: Electromagnetic compatibility (EMC) requirements - - IEC 62133 series Secondary cells and batteries containing alkaline or other non-acid electrolytes - Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications EN 62133 seri

45、es IEC 62282-2 - Fuel cell technologies - Part 2: Fuel cell modules EN 62282-2 - ISO 3864 series Graphical symbols - Safety colours and safety signs - - ISO 7000 - Graphical symbols for use on equipment - Registered symbols - - ISO 7010 - Graphical symbols - Safety colours and safety signs - Registe

46、red safety signs EN ISO 7010 - ISO 15649 - Petroleum and natural gas industries - Piping - - ISO 16000-3 - Indoor air Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air - Active sampling method - - ISO 16000-6 - Indoor air Part 6: Determination of v

47、olatile organic compounds in indoor and test chamber air by active sampling on Tenax TA sorbent, thermal desorption and gas chromatography using MS or MS-FID - - ISO 16017-1 2000 Indoor, ambiant and workplace air - Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorptio

48、n/capillary gas chromatography Part 1: Pumped sampling EN ISO 16017-1 2000 ISO 16111 - Transportable gas storage devices - Hydrogen absorbed in reversible metal hydride - - ISO 16528 series Boilers and pressure vessels - - BS EN IEC 622825100:2018This page deliberately left blank 2 IEC 62282-5-100:2

49、018 IEC 2018 CONTENTS FOREWORD . 6 1 Scope 8 2 Normative references 10 3 Terms and definitions 13 4 Design and construction requirements . 18 4.1 Physical environment and operating conditions . 18 4.1.1 General requirements 18 4.1.2 Electrical power input 18 4.1.3 Handling, transportation, and storage 18 4.2 Material compatibility 18 4.2.1 General requirements for material compatibility . 18 4.2.2 Polymeric and ela