EN 9300-115-2018 Aerospace series - LOTAR - LOng Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data - Part 115 .pdf

《EN 9300-115-2018 Aerospace series - LOTAR - LOng Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data - Part 115 .pdf》由会员分享，可在线阅读，更多相关《EN 9300-115-2018 Aerospace series - LOTAR - LOng Term Archiving and Retrieval of digital technical product documentation such as 3D CAD and PDM data - Part 115 .pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM dataPart 115: Explicit CAD assembly structureBS EN 9300115:2018National forewordThis British St

2、andard is the UK implementation of EN 9300115:2018.The UK participation in its preparation was entrusted to Technical Committee ACE/1, International and European Aerospace Policy and Processes.A list of organizations represented on this committee can be obtained on request to its secretary.This publ

3、ication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 63782 7ICS 01.110; 35.240.10; 35.240.30; 49.020Compliance with a British Sta

4、ndard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 9300115:2018EUROPEAN STANDARDNORME EUROPENN

5、EEUROPISCHE NORMEN 9300115July 2018ICS 01.110; 35.240.10; 35.240.30; 49.020EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCENCENELEC Management Centre: Avenue Marnix 17, B1000 Brussels 2018 CEN Ref. No. EN 9300115:2018: EAll rights of exploitation i

6、n any form and by any means reserved worldwide for CEN national MembersAerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D, CAD and PDM data Part 115: Explicit CAD assembly structurelment introductif LOTAR Archivage Long Terme et rcupration

7、des donnes techniques produits numriques,telles que CAD 3D et PDM Partie 115: Structure dassemblage CAO expliciteLuft und Raumfahrt LOTAR LangzeitArchivierung und Bereitstellung digitaler technischer Produktdokumentationen, wie zum Beispiel von 3D, CAD und PDMDaten Teil 115: Explizite CADBaugruppens

8、trukturenThis European Standard was approved by CEN on 25 September 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Uptodate lists and bibliograph

9、ical references concerning such national standards may be obtained on application to the CENCENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility

10、of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Ma

11、cedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN 9300115:2018 (E)European foreword iii1 Scope .

12、 42 Normative references 53 Terms, definitions and abbreviations 54 Applicability 55 Business specifications for the long term archiving and retrieval of the explicit CAD assembly structure . 55.1 Use cases 55.1.1 UC1: Full archiving . 55.1.2 UC2: Bottom up and incremental archiving . 66 Essential i

13、nformation for explicit CAD assembly structure 66.1 CAD Nodes representing part and assembly . 66.1.1 Part identification: 66.1.2 Part properties /attributes (optional): . 66.2 CAD Assembly structure relationship . 76.2.1 Child / parent identification 76.2.2 Geometric positioning . 76.3 References o

14、n sub-assembly files or 3D model files. 77 Definition of Core Model for an explicit CAD assembly structure . 87.1 Core model STEP AIM level 88 Verification rules of CAD explicit assembly structure . 98.1 Rules description 98.1.1 Unique CAD assembly structure . 98.1.2 No orphans 98.1.3 Acyclic assemb

15、ly structure . 108.1.4 Content of the assembly occurrences .108.1.5 3D explicit positioning of assemblies and parts 108.1.6 Identification of parts and assemblies .118.2 Definition of verification level for EN 9300-115.119 Validation rules of an explicit CAD assembly structure 119.1 The Purpose of V

16、alidation Properties 119.2 Validation properties 129.2.1 Geometric validation properties for assembly structure .129.2.2 Assembly Validation Properties. 139.3 Definition of validation level for EN 9300-115 149.3.1 Validation level at the ingest . 149.3.2 Validation level at retrieval 14Annex A (info

17、rmative) Recommended archiving scenarios 16iiContents PageBS EN 9300115:2018EN 9300115:2018 (E)European forewordThis document (EN 9300-115:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN).After enquiries and votes carried out in accor

18、dance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN.This European Standard shall be given the status of a national standard, either by publication of

19、an identical text or by endorsement, at the latest by January 2019, and conflicting national standards shall be withdrawn at the latest by January 2019.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not b

20、e held responsible for identifying any or all such patent rights.According to the CENCENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Esto

21、nia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.ForewordThis sta

22、ndard was prepared jointly by AIA, ASDSTAN, PDES Inc and the PROSTEP iViP Association.The PROSTEP iViP Association is an international non-profit association in Europe. For establishing leadership in ITbased engineering it offers a moderated platform to its nearly 200 members from leading industries

23、, system vendors and research institutions. Its product and process data standardization activities at European and worldwide levels are well known and accepted. The PROSTEP iViP Association sees this standard and the related parts as a milestone of product data technology.PDES Inc is an internation

24、al non-profit association in USA. The mission of PDES Inc is to accelerate the development and implementation of ISO 10303, enabling enterprise integration and PLM interoperability for member companies. PDES Inc gathers members from leading manufacturers, national government agencies, PLM vendors an

25、d research organizations. PDES Inc. supports this standard as an industry resource to sustain the interoperability of digital product information, ensuring and maintaining authentic longevity throughout their product lifecycle.Readers of this standard should note that all standards undergo periodic

26、revisions and that any reference made herein to any other standard implies its latest edition, unless otherwise stated.The Standards will be published under two different standards organizations using different prefixes. ASD Stan will publish the standard under the number EN 9300xxx. AIA will publis

27、h the standard under the number NAS 9300xxx. The content in the EN 9300 and NAS 9300 documents will be the same. The differences will be noted in the reference documentation (i.e. for EN 9300 Geometric Dimensioning however no specific verification and validation rules for this geometry are defined.O

28、ut of scope: The archiving of the geometric model of the components; The management of different occurrences of the same part that have different geometry; The management of different occurrences of the same part that have different attributes;4 BS EN 9300115:2018EN 9300115:2018 (E) The archiving of

29、 assembly-by-constraint (where, for example, the position of a part is given as “perpendicular to part X”, rather than given as a positioning matrix); The archiving of the Geometrical Dimensioning and Tolerance (GD The archiving of assembly Form Features.NOTE 2 Product assembly structure may be defi

30、ned based on the data base management system approach. This case uses other fundamental concepts not covered in this part. See family EN 93002xx.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this

31、document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 9300 (all parts), Aerospace series LOTAR LOng Term Archiving and Retrieval of digital technical product documentation such as 3D

32、, CAD and PDM dataISO 1030344:2000, Industrial automation systems and integration Product data representation and exchange Part 44: Integrated generic resource: Product structure configurationPDM and CAX implementor forum documents: “Usage Guide for the STEP PDM schema v1.2” Released 4.3 January 200

33、2; “Recommended Practices for External References with References to the PDM Schema Usage Guide”; “Recommended Practices for Geometric Validation Properties”; “Recommended practices for Assembly Validation Properties”.3 Terms, definitions and abbreviationsFor the purposes of this standard, the terms

34、, definitions and abbreviations given in EN 9300-007 shall apply.4 ApplicabilityRefer to applicability of EN 9300001, Clause 4.5 Business specifications for the long term archiving and retrieval of the explicit CAD assembly structure5.1 Use casesThe following clauses record the potential use cases f

35、or the archiving of an explicit CAD assembly structure. “Annex A: Recommended archiving scenarios” identifies the main archiving scenarios corresponding to these two use cases.5.1.1 UC1: Full archivingThe term “full archiving” is used where the complete assembly structure is archived as a single uni

36、t, and all the assembly structure data are contained in the same Submission Information Package (SIP). The assembly may be contained in one file or in a set of files (see Figure 3: archiving overview of the submission information package).5BS EN 9300115:2018EN 9300115:2018 (E)Figure 3 Archiving over

37、view of the submission information package5.1.2 UC2: Bottom up and incremental archivingThe assembly structure is archived subset by subset. The assembly structure files are submitted in different submission information packages. For example, in bottomup archiving, the assembly structure files are s

38、ubmitted from the lower level up to the top level (see Figure 4).Figure 4 Bottom up archiving of the assembly structure6 Essential information for explicit CAD assembly structureThe following list describes the essential information for a CAD assembly structure. The essential information are capture

39、d, verified and validated through the core model and the rules. The core model is described in the Clause 7 “Definition of Core Model for an explicit CAD assembly structure” and the rules are described in the Clause 8 “Verification rules of CAD explicit assembly structure” and Clause 9 “Validation r

40、ules off an explicit CAD assembly structure”.6.1 CAD Nodes representing part and assembly6.1.1 Part identification: Part number: Unique Identifier of a part; Name: Human readable name of the part (e.g. bolt-CHC-M6); Description: Additional human readable information about the part; Version (optional

41、): Unique identification of the version (e.g. A001).6.1.2 Part properties /attributes (optional): View / context of definition: e.g. As Designed; Systems Unit (mm, ).Occurrence / Instance identification (optional)6 BS EN 9300115:2018EN 9300115:2018 (E)6.2 CAD Assembly structure relationship6.2.1 Chi

42、ld / parent identificationIdentification of the two nodes - the parent and the child (optional: Occurrence/ Instance identification for the parent and the child)6.2.2 Geometric positioningDefining the location and orientation of the related geometric component relative to the relating geometric asse

43、mbly, e.g., Positioning matrix (translation X, Y,Z, Rotation, )6.3 References on sub-assembly files or 3D model filesThis information is only relevant to leaf nodes representing parts. External part identification: part number, name, description, version; External file identification: Name: Unique i

44、dentifier of the file; Version (optional): Unique identifier of the file version. File properties: Format: Specification of the file format, e.g., ISO 10303-214; Type: For a geometry file, identification of the type of geometry, e.g. surface model, closed volume, solid model etc.Figure 5 Main essent

45、ial objects of the assembly file to be preserved7BS EN 9300115:2018EN 9300115:2018 (E)7 Definition of Core Model for an explicit CAD assembly structure7.1 Core model STEP AIM levelThe core model is based on a subset of the STEP PDM schema v1.2 and the associated usage guide PDM.The STEP PDM Schema i

46、s a core set of entities in STEP that support the concepts for Product Data Management (PDM). The PDM Schema has been established to promote interoperability between STEP APs (AP214 and AP203) in the area of product data management.The following list identifies which subsets of the “usage Guide for

47、the STEP PDM schema v1.2” are reused for the core model of the part 115.1 Part Identification1.1 Part as Product1.1.1 Product Master Identification1.1.2 Context Information / Next assembly1.1.3 Type Classification2 Specific Part Type Classification2.1 Classification of parts and managed documents3 P

48、art Properties3.1 General Part Properties3.1.1 Properties Associated with Product Data3.2 External Part Shape3.2.1 Geometric Shape Property3.2.3 Relating Externally Defined Part Shape to an External File3.3 External Geometric Model Structure3.3.1 Relating Part Shape3.3.3 Additional Geometric Model S

49、tructures3.4 Relative Orientation and Location of Related Geometric Modelsi Implicitly defined transformations between geometric models4 Part Structure and Relationships4.1 Explicit Assembly Bill Of Material4.2 MultiLevel Assembly Digital Mock Up4.3 Different Views on Assembly Structure4.4 Relating Part Shape Properties to Product Structure4.4.2 Implicit Relationships Between Assembly Components7 External Files7.1 External File Identification8 BS EN 9300115:2018EN 9300115:201