EN 3542-2018 Aerospace series - Inserts screw thread helical coil self-locking in heat resisting nickel base alloy NI-PH2801 (Inconel X750).pdf

《EN 3542-2018 Aerospace series - Inserts screw thread helical coil self-locking in heat resisting nickel base alloy NI-PH2801 (Inconel X750).pdf》由会员分享，可在线阅读，更多相关《EN 3542-2018 Aerospace series - Inserts screw thread helical coil self-locking in heat resisting nickel base alloy NI-PH2801 (Inconel X750).pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Aerospace series - Inserts, screw thread, helical coil, self-locking, in heat resisting nickel base alloy NI-PH2801 (Inconel X750)BS EN 3542:2018National forewordThis British Standard is the UK implementation of EN 3542

2、:2018. It supersedes BS EN 3542:1998, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication d

3、oes not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 51692 4ICS 49.030.30Compliance with a British Standard cannot confer immunity from le

4、gal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 3542:2018EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3542April 2018ICS

5、49.030.30 Supersedes EN 3542:1998EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2018 CEN Ref. No. EN 3542:2018: EAll rights of exploitation in any form and by any means reserved worldw

6、ide for CEN national MembersAerospace series - Inserts, screw thread, helical coil, self-locking, in heat resisting nickel base alloy NI-PH2801 (Inconel X750)Srie arospatiale - Filets rapports, freinage interne, en alliage rsistant chaud base de nickel NI-PH2801 (Inconel X750)Luft- und Raumfahrt - D

7、raht-Gewindeeinstze, selbstsichernd, aus hochwarmfester Nickelbasislegierung NI-PH2801 (Inconel X750)This European Standard was approved by CEN on 22 January 2018.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standar

8、d the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, F

9、rench, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgari

10、a, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerlan

11、d, Turkey and United Kingdom.English VersionEN 3542:2018 (E)European foreword 3Introduction . 41 Scope . 52 Normative references 53 Required characteristics 53.1 Configuration Dimensions Tolerances Masses 53.2 Material . 53.3 Material identification 54 Designation .105 Marking .106 Technical specifi

12、cation 102Contents PageBS EN 3542:2018EN 3542:2018 (E)European forewordThis document (EN 3542:2018) has been prepared by the Aerospace and Defence Industries Association of Europe Standardization (ASD -STAN).After enquiries and votes carried out in accordance with the rules of this Association, this

13、 Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the la

14、test by October 2018, and conflicting national standards shall be withdrawn at the latest by October 2018.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rig

15、hts.This document supersedes EN 3542:1998.According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Y

16、ugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.3BS EN 3542:2018EN 3542:2018 (E)Introd

17、uctionFor design and assembly procedures see EN 3044 and EN 2945.4BS EN 3542:2018EN 3542:2018 (E)1 ScopeThis document specifies the characteristics of inserts, self-locking, helical coil, tanged insertion drive, with MJ screw thread in NI-PH2801 material, for aerospace applications.Maximum test temp

18、erature: 550 C.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docum

19、ent (including any amendments) applies.EN 2424, Aerospace series Marking of aerospace productsEN 2943, Aerospace series Inserts, screw thread, helical coil, selflocking Technical specificationEN 2945, Aerospace series Inserts, screw thread, helical coil, selflocking Assembly procedureEN 3018, Aerosp

20、ace series Heat resisting alloy NIPH2801 (NiCr16Fe7Ti3Nb1Al1), with consumable electrode remelted Cold drawn wire for the manufacture of thread inserts D 3 mm1)EN 3044, Aerospace series Installation holes for inserts, screw thread, helical coil, selflocking Design standardISO 5855-2, Aerospace MJ th

21、reads Part 2: Limit dimensions for bolts and nuts3 Required characteristics3.1 Configuration Dimensions Tolerances MassesSee Figure 1 and Table 1 and Table 2. Dimensions and tolerances are in millimetres.3.2 MaterialSee EN 3018.3.3 Material identificationColour: yellow.No chlorine-based constituents

22、 permitted in the colour identification product.1) Published as ASD-STAN pre-standard at the date of publication of the present standard (www.asd-stan.org).5BS EN 3542:2018EN 3542:2018 (E)Keya form out-of-round in this area to achieve the self-locking requirements (tool marks permissible)b tangc num

23、ber of coilsd markinge lead-in face of installation holef installationg see detail Y6 BS EN 3542:2018EN 3542:2018 (E)h min. profilei max. profilej R, min, tangential to flanksk straight portion of flankl locking feature shall be at least in the zone Y max. X min. It shall take place on at least two

24、coils separated by a plain coil, except in the case of inserts of diameters 4, 5 and 6 and a nominal length of 1,25 D where the plain coil may be omittedm the number of coils is counted from the notchp length of fitted insert to notchq dimensions after coiling, corresponding to an insert fitted in a

25、n installation hole to EN 3044r section A-A is perpendicular to the helical axisFigure 1 Layout drawing, dimensions destined for design depts.7BS EN 3542:2018EN 3542:2018 (E)Table1 DimensionsDiametercodeThreada(Associatedscrew)ABmin.BmaxCmaxCminEmaxEminFHmaxHminJPPR1SUUVAAmin.max.max. minmax.min.min

26、.min.max.min.max.max.min.040MJ40,70,1635,055,600,7580,6830,6120,510,350,4550,44455,64,93,552,50,1260,2191,671,020,450,340,31050MJ50,80,2096,256,800,8660,7750,70,5980,40,520,50856,86,14,553,151,1440,252,091,410,60,370,34060MJ610,2677,407,951,0830,9750,8750,7480,50,650,6377,957,254,853,70,180,3122,551

27、,650,50,45070MJ718,659,209,28,45,54,33,12,090,75080MJ819,7010,25109,26,54,753,882,27100MJ101,257,407,957,407,957,407,957,407,957,407,957,407,957,407,957,407,957,407,950,60,55aIn accordance with ISO5855-2. 8 BS EN 3542:2018EN 3542:2018 (E)Table2 Dimensions,Numberofturns,mass(1of2)DiametercodeThreada(

28、Associatedscrew)LL1NumberofturnsQ0,25Xbmin.YbMasskg/1000pieces1,5D2 D2,5 D1,5D2 D2,5 D1,5D2 D2,5 D1,5D2 D2,5 D1,5D2 D2,5 D1,5D2 D2,5 D040MJ40,768105,477,479,476,18,611,10,82,53,14,80,220,310,39050MJ50,87,51012,56,909,4011,906,99,612,41,33,83,73,96,36,30,40,550,7060MJ61912158,2511,2514,256,89,512,12,

29、25,10,720,991,26070MJ7110,51417,59,7513,2516,75811,114,11,25,95,50,991,361,73080MJ8112162011,2515,2519,259,41316,52,56,81,321,82,28100MJ101,2515202514,2519,2524,259,513,116,83,72,573,524,46aIn accordance with ISO5855-2. bXand Ydimensions apply after installation of the thread insert. 9BS EN 3542:201

30、8EN 3542:2018 (E)4 DesignationEXAMPLE NOTE lf necessary, the code I9005 shall be placed between the description block and the identity block.5 MarkingSee EN 2424. style G; additionally style F permitted, as indicated on Figure 1.6 Technical specificationSee EN 2943.10 BS EN 3542:2018This page delibe

31、rately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI St

32、andards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dep

33、endable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Sta

34、ndards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchas

35、ed.If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or so

36、me person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standar

37、d to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft cop

38、y format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or intern

39、al company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 cop

40、y of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of

41、 subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 2

42、4/7 and is refreshed daily so youll always be up to date.You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member.PLUS is an updating service exclusive to

43、BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards pub

44、lications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revi

45、sion. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: BSI Group Headquarters389 Chiswick High Road London W4 4AL UKNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW