EN 13451-10-2018 Swimming pool equipment - Part 10 Additional specific safety requirements and test methods for diving platforms diving springboards and associa.pdf

《EN 13451-10-2018 Swimming pool equipment - Part 10 Additional specific safety requirements and test methods for diving platforms diving springboards and associa.pdf》由会员分享，可在线阅读，更多相关《EN 13451-10-2018 Swimming pool equipment - Part 10 Additional specific safety requirements and test methods for diving platforms diving springboards and associa.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Swimming pool equipmentPart 10: Additional specific safety requirements and test methods for diving platforms, diving springboards and associated equipmentBS EN 13451-10:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE

2、NORM EN 13451-10 August 2018 ICS 97.220.10 Supersedes EN 13451-10:2014English Version Swimming pool equipment - Part 10: Additional specific safety requirements and test methods for diving platforms, diving springboards and associated equipment quipement de piscine - Partie 10 : Exigences de scurit

3、et mthodes dessai complmentaires propres aux plates-formes de plongeon, aux plongeoirs et lquipement associ Schwimmbadgerte - Teil 10: Zustzliche besondere sicherheitstechnische Anforderungen und Prfverfahren fr Sprungplattformen, Sprungbretter und zugehrige Gerte This European Standard was approved

4、 by CEN on 6 May 2018. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standar

5、ds may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and noti

6、fied to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Ic

7、eland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CEN

8、ELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13451-10:2018 ENational forewordThis British Standard is the UK implementation of EN 13451-10:2018. It supersedes BS

9、 EN 13451-10:2014, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee SW/136/8, Swimming pools and aquatic equipment.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to inc

10、lude all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 94177 1ICS 97.220.10Compliance with a British Standard cannot confer immunity from legal obligations.This B

11、ritish Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 13451-10:2018EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13451-10 August 2018 ICS 97.22

12、0.10 Supersedes EN 13451-10:2014English Version Swimming pool equipment - Part 10: Additional specific safety requirements and test methods for diving platforms, diving springboards and associated equipment quipement de piscine - Partie 10 : Exigences de scurit et mthodes dessai complmentaires propr

13、es aux plates-formes de plongeon, aux plongeoirs et lquipement associ Schwimmbadgerte - Teil 10: Zustzliche besondere sicherheitstechnische Anforderungen und Prfverfahren fr Sprungplattformen, Sprungbretter und zugehrige Gerte This European Standard was approved by CEN on 6 May 2018. CEN members are

14、 bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to t

15、he CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Cen

16、tre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuan

17、ia, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Scie

18、nce 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13451-10:2018 EBS EN 13451-10:2018EN 13451-10:2018 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms and

19、 definitions . 5 4 Safety requirements . 6 4.1 Tolerances . 6 4.2 Diving platforms 6 4.3 Diving springboards 12 4.4 Means of access . 17 4.5 Safety barriers . 18 4.6 Slip resistance . 19 4.7 Water diving zones 20 4.8 Agitation of water surface . 20 4.9 Air cushion equipment . 20 5 Test methods . 21

20、5.1 General . 21 5.2 Structural integrity of diving springboards . 21 5.3 Structural integrity of stepladders 22 5.4 Structural integrity of safety barriers 23 Annex A (informative) Adeviations 24 Bibliography . 26 BS EN 13451-10:2018EN 13451-10:2018 (E) 3 European foreword This document (EN 13451-1

21、0:2018) has been prepared by Technical Committee CEN/TC 136 “Sports, playground and other recreational facilities and equipment”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorse

22、ment, at the latest by February 2019, and conflicting national standards shall be withdrawn at the latest by February 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or a

23、ll such patent rights. This document supersedes EN 13451-10:2014. In relation to EN 13451-10 the following main amendments have been made: a) the values in Tables 2 and 4 have been compared with and where required revised according to the values of the current FINA Table; b) clause on stepladders fo

24、r diving facilities revised (4.4.2); c) clause on safety barriers revised (4.5); d) clause on slip resistance revised (4.6); e) Adding informative Annex regarding A-Deviation from Estonia. This document includes an A-Deviation from Estonia. The EN 13451 series, Swimming pool equipment consists of th

25、e following parts: Part 1: General safety requirements and test methods Part 2: Additional specific safety requirements and test methods for ladders, stepladders and handle bends Part 3: Additional specific safety requirements and test methods for inlets and outlets and water/air based water leisure

26、 features Part 4: Additional specific safety requirements and test methods for starting platforms Part 5: Additional specific safety requirements and test methods for lane lines and dividing line Part 6: Additional specific safety requirements and test methods for turning boards Part 7: Additional s

27、pecific safety requirements and test methods for water polo goals Part 10: Additional specific safety requirements and test methods for diving platforms, diving springboards and associated equipment Part 11: Additional specific safety requirements and test methods for moveable pool floors and moveab

28、le bulkheads According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia

29、, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13451-10:2018EN 13451-10:2018 (E) 4 Introduction Diving is a

30、 voluntary movement into water with arms and head entering the water first or a voluntary movement into water with feet entering the water first while performing acrobatics. There can be additional requirements for purposes such as competition swimming, and advice should be sought from the governing

31、 body of the sport in question (see 1 and 2). BS EN 13451-10:2018EN 13451-10:2018 (E) 5 1 Scope This part of the EN 13451 series specifies safety requirements for diving platforms, diving springboards and associated equipment in addition to the general safety requirements of EN 13451-1 and is meant

32、to be read in conjunction with it. The requirements of this part of the EN 13451 series take priority over those in EN 13451-1. This part of the EN 13451 series is applicable to platforms and springboards, and associated equipment for use in classified swimming pools as specified in EN 15288-1 and E

33、N 15288-2. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document

34、 (including any amendments) applies. EN 13451-1:2011+A1:2016, Swimming pool equipment Part 1: General safety requirements and test methods EN 13451-3, Swimming pool equipment Part 3: Additional specific safety requirements and test methods for inlets and outlets and water/air based water leisure fea

35、tures EN 22768-1, General tolerances Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13451-1:2011+A1:2016 and the following apply. ISO and IEC m

36、aintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp 3.1 diving facility installation designed to provide the opportunity of diving 3.2 divin

37、g platform raised rigid horizontal platform, protruding over the water, intended for diving 3.3 diving springboard type 1 raised flexible board, installed at a height 1,0 m h 3,05 m above water level and protruding over the water, intended for diving 3.4 diving springboard type 2 raised flexible boa

38、rd, which can be permanently installed or portable, with a height 1,0 m from water level and protruding over the water, intended for recreational diving BS EN 13451-10:2018EN 13451-10:2018 (E) 6 3.5 plummet line vertical line extending through the centre of the front edge of a platform or springboar

39、d 3.6 water agitation device equipment designed to improve visibility of the water surface by disturbance 3.7 air cushion equipment training device, designed for introducing air from the bottom of a diving pool, in front of a diving platform and/or springboard, to reduce the effects of the impact of

40、 the diver with the pool water and make training safer 4 Safety requirements 4.1 Tolerances Tolerances of height of the diving platform and diving springboards are +0 050m,. For all other tolerances, if not indicated, EN 22768-1 applies. 4.2 Diving platforms 4.2.1 General Particular attention shall

41、be paid to avoid glare and reflecting surfaces, which can disturb the vision of the diver. In Europe, outdoor diving facilities should face north. 4.2.2 Dimensions The dimensions indicated in Figures 1 to 4 and Tables 1 to 2 shall be complied with. The design of the equipment does not need to comply

42、 with the examples given. Platforms shall be horizontal. The minimum dimensions of the platforms shall comply with Table 1. Table 1 Areas of use Dimensions in metres Height of platforms from water level Minimum usable width Length reserved for the divera1 0,60 0,75 3 0,60 1,25 5 1,50 1,25 7,5 1,50 1

43、,50 10 3,00 1,50 aMinimum distance back from plummet. BS EN 13451-10:2018EN 13451-10:2018 (E) 7 NOTE 1 In addition to the length reserved for the diver (minimum distance back from plummet), additional space can be necessary for other purposes, as wider range of dives (e.g. dives with preliminary run

44、), space for waiting for the dive, space for divers passing to the next platform. If synchronized diving (more than one diver starting at a same time from the platform) is foreseen, the width of the platforms should be suitably increased. As an alternative, during synchronized diving activities only

45、 there should be the possibility to increase temporarily the distance of the safety barriers for arm movement (see 1). The minimum dimensions of the platform facilities shall comply with Table 2 and with Figure 1. Table 2 Minimum dimensions of diving platform facilities Dimensions in metres Minimum

46、height of platform from water level 1 m 3 m 5 m 7,5 m 10 m horizontal vertical horizontal vertical horizontal vertical horizontal vertical horizontal vertical A From plummet back to pool wall 0,75 1,25 1,25 1,25 1,50 A/AaFrom plummet back to platform plummet vertically below 0,75 0,75 0,75 BbFrom pl

47、ummet to pool wall at side 2,30 2,80 3,25 4,25 5,25 Cb, cFrom plummet to adjacent plummet 1,65 2,00 2,25 2,50 2,75 D From plummet to pool wall ahead 8,00 9,50 10,25 11,00 13,50 E On plummet, from board to ceiling 3,25 3,25 3,25 3,25 4,00 FdDistance behind and each side of plummet with height E 2,30

48、2,75 2,75 2,75 2,75 G Distance ahead of plummet with height E 5,00 5,00 5,00 5,00 6,00 H Depth of water at plummet 3,20 3,50 3,70 4,10 4,50 J Distance ahead of plummet with a water depth K 4,50 5,50 6,00 8,00 11,00 K minimum water depth between plummet and distance J 3,10 3,40 3,60 4,00 4,25 L Dista

49、nce on each side of plummet with a water depth M 1,40 1,80 3,00 3,75 4,50 M minimum water depth between plummet and distance L 3,10 3,40 3,60 4,00 4,25 BS EN 13451-10:2018EN 13451-10:2018 (E) 8 aon plummet, also from platform to the bottom side of a platform, if vertically above bDimensions B and C apply to platforms with widths as in Table 1; if platform widths are