EN 12274-2-2018 Slurry surfacing - Test methods - Part 2 Determination of residual binder content including preparation of samples.pdf

《EN 12274-2-2018 Slurry surfacing - Test methods - Part 2 Determination of residual binder content including preparation of samples.pdf》由会员分享，可在线阅读，更多相关《EN 12274-2-2018 Slurry surfacing - Test methods - Part 2 Determination of residual binder content including preparation of samples.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Slurry surfacing Test methodsPart 2: Determination of residual binder content including preparation of samplesBS EN 122742:2018National forewordThis British Standard is the UK implementation of EN 122742:2018. It supers

2、edes BS EN 122742:2003, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee B/510/2, Surface treatments.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the n

3、ecessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 92276 3ICS 93.080.20; 91.100.50Compliance with a British Standard cannot confer immunity from legal obligations.This Brit

4、ish Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 122742:2018EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 122742March 2018ICS 93.080.20 Supersedes E

5、N 122742:2003EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCENCENELEC Management Centre: Avenue Marnix 17, B1000 Brussels 2018 CEN Ref. No. EN 122742:2018: EAll rights of exploitation in any form and by any means reserved worldwide for CEN national

6、 MembersSlurry surfacing Test methods Part 2: Determination of residual binder content including preparation of samplesMatriaux bitumineux couls froid Mthode dessai Partie 2: Dtermination de la teneur en liant rsiduel y compris la prparation des chantillonsDnne Asphaltdeckschichten in Kaltbauweise P

7、rfverfahren Teil 2: Bestimmung des Bindemittelgehaltes einschlielich ProbenvorbereitungThis European Standard was approved by CEN on 13 November 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status

8、of a national standard without any alteration. Uptodate lists and bibliographical references concerning such national standards may be obtained on application to the CENCENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German).

9、A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cypr

10、us, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and Un

11、ited Kingdom.English VersionEN 122742:2018 (E)European forewordThis document (EN 12274-2:2018) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication

12、of an identical text or by endorsement, at the latest by September 2018, and conflicting national standards shall be withdrawn at the latest by September 2018.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held r

13、esponsible for identifying any or all such patent rights.This document supersedes EN 122742:2003.Compared with EN 122742:2003, the following changes have been made:a) binder content by ignition is enabled using EN 12697-39;b) an alternative method to oven-drying prior to binder extraction can be use

14、d with provision for collection of water during the solvent extraction process, as specified in EN 12697-1:2012, Annex B.This European Standard is one of a series of standards as listed below: EN 122741, Slurry surfacing Test methods Part 1: Sampling of slurry surfacing mixture EN 122742, Slurry sur

15、facing Test methods Part 2: Determination of residual binder content including preparation of samples EN 122743, Slurry surfacing Test methods Part 3: Consistency EN 122744, Slurry surfacing Test methods Part 4: Determination of cohesion of the mix EN 122745, Slurry surfacing Test methods Part 5: De

16、termination of the minimum binder content and wearing resistance EN 122746, Slurry surfacing Test methods Part 6: Rate of application EN 122747, Slurry surfacing Test methods Part 7: Shaking abrasion test EN 122748, Slurry surfacing Test methods Part 8: Visual assessment of defectsAccording to the C

17、ENCENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hunga

18、ry, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.2BS EN 122742:2018EN 122742:2018 (E)European foreword 2European foreword 41 Scope . 52 Normative re

19、ferences 53 Principle 54 Apparatus . 54.1 Apparatus used for preparation of samples 54.2 Apparatus used for testing 65 Preparation of sample 66 Test procedure 67 Test report . 68 Precision . 73Contents PageBS EN 122742:2018EN 122742:2018 (E)European forewordThis document (EN 12274-2:2018) has been p

20、repared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2018, and conflicting national standar

21、ds shall be withdrawn at the latest by September 2018.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.This document supersedes EN 122742:2003.Compared

22、 with EN 122742:2003, the following changes have been made:a) binder content by ignition is enabled using EN 12697-39;b) an alternative method to oven-drying prior to binder extraction can be used with provision for collection of water during the solvent extraction process, as specified in EN 12697-

23、1:2012, Annex B.This European Standard is one of a series of standards as listed below: EN 122741, Slurry surfacing Test methods Part 1: Sampling of slurry surfacing mixture EN 122742, Slurry surfacing Test methods Part 2: Determination of residual binder content including preparation of samples EN

24、122743, Slurry surfacing Test methods Part 3: Consistency EN 122744, Slurry surfacing Test methods Part 4: Determination of cohesion of the mix EN 122745, Slurry surfacing Test methods Part 5: Determination of the minimum binder content and wearing resistance EN 122746, Slurry surfacing Test methods

25、 Part 6: Rate of application EN 122747, Slurry surfacing Test methods Part 7: Shaking abrasion test EN 122748, Slurry surfacing Test methods Part 8: Visual assessment of defectsAccording to the CENCENELEC Internal Regulations, the national standards organisations of the following countries are bound

26、 to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

27、 Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.4BS EN 122742:2018EN 122742:2018 (E)1 ScopeThis European Standard specifies test methods for determining the residual binder content of samples of slurry surfacing mixtures.This document describes the met

28、hod for preparing the specimens and for removing water from the samples before carrying out the extraction test.The method described in this European Standard needs to be used only to determine the quantity of binder and not to investigate its quality.This European Standard applies to slurry surfaci

29、ng to be used in surface layers for roads, airfields and other trafficked areas.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated

30、 references, the latest edition of the referenced document (including any amendments) applies.EN 122741, Slurry surfacing Test methods Part 1: Sampling for binder extractionEN 126971:2012, Bituminous mixtures Test methods for hot mix asphalt Part 1: Soluble binder contentEN 126973, Bituminous mixtur

31、es Test methods for hot mix asphalt Part 3: Bitumen recovery: Rotary evaporatorEN 126974, Bituminous mixtures Test methods Part 4: Bitumen recovery: Fractionating columnEN 1269739, Bituminous mixtures Test methods for hot mix asphalt Part 39: Binder content by ignition3 PrincipleWater is removed fro

32、m the sample by ovendrying or by collection during the solvent extraction process.The soluble binder content of the sample is determined in accordance with EN 126971:2012, Clause 5.Binder content by non-extractive method such as ignition (e.g. according to EN 12697-39) can be used provided a correla

33、tion has been demonstrated.In case of dispute, EN 126971:2012, Clause 5 shall be used.4 Apparatus4.1 Apparatus used for preparation of samples1) Oven, with a suitable capacity and capable of holding the required temperatures.2) Balance having a suitable range capable of weighing a sample to the near

34、est 0,1 g.3) Container, comprising a metal tray or pot.4) End-rounded spatula or metal rod.5) Sampling container.5BS EN 122742:2018EN 122742:2018 (E)4.2 Apparatus used for testingBinder extraction apparatus shall conform to the requirements of EN 126971:2012, Annex B, or alternative methods: EN 1269

35、739 provided a correlation has been demonstrated.There is also provision in EN 12697-1:2012 for the use of the equipment specified in EN 12697-3 or EN 126974 for the case of binder quantity by total recovery.5 Preparation of sample1) The samples of slurry surfacing mixture shall be taken from the sl

36、urry surfacing machine in accordance with EN 122741.2) Transfer the sample from the sampling container to a tray large enough to contain all of the sample when it is broken into small pieces. Break the sample into small pieces of such a size that the water can readily evaporate.NOTE In order to remo

37、ve the entire contents from the sampling container, it is often useful to cut the sides of the container open to regain all the binder.3) Place the broken pieces of the sample in a thin layer on a tray in an oven at a temperature of between 110 and 170 5C, until constant mass. For a temperature of (

38、110 5)C, constant mass is deemed to be achieved when the difference between successive weightings at least at 60 min intervals does not exceed 0,1 % of the mass.4) Mix the broken sample thoroughly and divide it into a test portion with a recommended mass depending on the aggregate size in accordance

39、 with Table 1. If sampling containers with 0,5 l for slurry surfacing mixture with coarse aggregate size 8 mm are used from production, then the entire contents of each container shall be tested without further sample division.Table 1 Recommended mass of test portionMaximum size of aggregatemm2 4 6

40、8 11Minimum mass, after drying, of a test portion g600 800 11005) An alternative method to oven-drying prior to binder extraction can be used with provision for collection of water during the solvent extraction process, as specified in EN 12697-1:2012, Annex B.6 Test procedureThe extraction test sha

41、ll be carried out in accordance with EN 126971:2012, Annex B or EN 1269739.If mixtures containing polymer modified binders are tested, the supplier should indicate the solvent and the extraction procedure should be used to recover the binder from such mixtures.7 Test reportThe test report shall stat

42、e that the test has been performed in accordance with this European Standard and shall contain the following information:a) name of the client;b) name and address of testing laboratory;6 BS EN 122742:2018EN 122742:2018 (E)c) incoming date of sample;d) a unique serial number for the test report;e) ty

43、pe and grade of slurry surfacing mixture;f) identification number of the sample;g) binder content to the nearest 0,1 % by mass;h) water content to the nearest 0,1 % by mass;i) whether or not sample was accompanied by a sampling protocol;j) identification of the test method for example: reference to

44、EN 12697-1:2012, Annex B, apparatus used;k) date of issue;l) signature of person accepting the technical responsibility for the test report;m) type of aggregate (if known or visual assessment);n) target binder content (if required);o) reference to this European Standard.p) any deviations from the te

45、st method.8 PrecisionInformation on the precision (statistical parameters for the repeatability and the reproducibility) is not known.7BS EN 122742:2018This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, info

46、rmation and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined

47、 experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals

48、.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publicat

49、ions, including British and adopted European and international standards, through our website at where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publicat