EN 10222-1-1998 Steel Forgings for Pressure Purposes - Part 1 General Requirements for Open Die Forgings (Incorporates Amendment A1 2002)《压力容器用钢锻件 第1部分 敞口铸模锻件的一.pdf

《EN 10222-1-1998 Steel Forgings for Pressure Purposes - Part 1 General Requirements for Open Die Forgings (Incorporates Amendment A1 2002)《压力容器用钢锻件 第1部分 敞口铸模锻件的一.pdf》由会员分享，可在线阅读，更多相关《EN 10222-1-1998 Steel Forgings for Pressure Purposes - Part 1 General Requirements for Open Die Forgings (Incorporates Amendment A1 2002)《压力容器用钢锻件 第1部分 敞口铸模锻件的一.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、Steel forgings for pressure purposes - Part 1: General requirements for open die forgings The European Standard EN 10222-1:1998, with the incorporation of amendment A1:2002, has the status of a British Standard ICs 77.140.85 NO COPYING WITHOUT BCI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS E

2、N 10222-1: 1998 Incorporating Amendment No. 1 Eritish Standards Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 10222-1:1998 Amd. No. 13923 National foreword Date Comments

3、11 October 2002 Addition of Annex ZA This British Standard is the English language version of EN 10222-1:1998, including amendment A1:2002, published by the European Committee for Standardization (CEN). Together with EN 10222-2 to -4 it supersedes BS 1503:1989 which will be withdrawn when the four p

4、arts of EN 10222 are published. The UK participation in its preparation was entrusted by Technical Committee ISE/73, Steels for pressure purposes, to Subcommittee ISE/73/3, Steel forgings for pressure purposes, which has the responsibility to: - aid enquirers to understand the text; - present to the

5、 responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request

6、to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Elect

7、ronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages T

8、his document comprises a front cover, an inside front cover, the EN title page, pages 2 to 15 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. This British Standard, having been prepared under the direction of the Engineering Sector B

9、oard, was published under the authority of the Standards Board and comes into effect on 15 May 1998 Q BI 11 October 2002 Amendments issued since publication ISBN O 580 29026 3 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or netw

10、orking permitted without license from IHS-,-,-EUROPEAN STANDARD NORME EUROPENNE EUROPAISCHE NORM EN 10222-1 Januaiy 1998 + Ai April 2002 ICs 77.140.85 Descriptors: Iron and steel products, forgings, steels, pressure equipment, designation, manufacturing, surface condition, grades: quality, chemical

11、composition, mechanical properties, sampling, tests, inspection, marking English version Steel forgings for pressure purposes - Part i: General requirements for open die forgings (including amendment A1:2002) Pices forges en acier pour appareils pression - Partie i: Prescriptions gnrales concernant

12、les pices obtenues par forgeage libre (inclut l?amendement A1:2002) Schmiedestcke aus Stahl fr Druckbehlter - Teil 1: Allgemeine Anforderungen an Freiformschmiedestcke (enthlt Anderung A1:2002) This European Standard was approved by CEN on 26 October 1997. Amendment Al was approved by CEN on 14 Marc

13、h 2002. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtain

14、ed on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secret

15、ariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN Eur

16、opean Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 0 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10222-1:1998 + A1:200

17、2 E Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 10222-1:1998 Foreword This European Standard has been prepared by Technical Committee ECISSITC 28 “Steel forgings”, the Sec

18、retariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 1998, and conflicting national standards shall be withdrawn at the latest by July 1998. The titles of the oth

19、er Parts of this European Standard are: Part 2: Ferritic and martensitic steels with specified elevated temperature properties. Part 3: Nickel steels with specified low temperature properties. Part 4: Weldable finegrain steels with high proof strength. Part 5: Martensitic, austenitic and austenitic-

20、ferritic stainless steels. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg

21、, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Foreword to amendment Ai This document EN 10222-1:1998/A1:2002, has been prepared by Technical Committee ECISSITC 28 Steel forgings, the Secretariat of which is held by BSI. This European Standard shall be given the

22、status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2002, and conflicting national standards shall be withdrawn at the latest by October 2002. This document has been prepared under a mandate given to CEN by the European Commission and

23、 the European Free Trade Association, and supports essential requirements of EU Directive($. For relationship EU Directive(+ see informative Annex ZA, which is an integral part of this document. According to the CENKENELEC Internal Regulations, the national standards organizations of the following c

24、ountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Norma

25、tive references 3 3 Definitions 4 4 Classification and designation 4 5 purchaser 4 6 Manufacture of the steel 5 7 Manufacture of the product 5 8 Surface condition and soundness 5 9 Chemical composition 6 i0 and low temperatures 6 11 Mechanical properties at elevated temperature 6 12 Sampling and pre

26、paration of test pieces 7 13 Mechanical test methods 9 14 Retests 9 15 Inspection 9 16 Marking 10 Annex A (normative) Options 11 Information to be supplied by the Mechanical properties at room temperature Annex B (informative) Ruling section and equivalent thickness 13 Annex ZA (informative) Clauses

27、 of this European Standard addressing essential requirements or other provisions of EU Directives Table 1 - Unit mass and batch mass limit Table B.l- Equivalent thickness for sections of shape different from the ruling sectionsa 15 7 14 2 Q BSI 11 October 2002 Copyright European Committee for Standa

28、rdization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 10222-1:1998 1 Scope This Part of this European Standard specifies the general technical delivery conditions for open die steel forgings, ring rolled products and for

29、ged bars for pressure purposes. General information on technical delivery conditions is given in EN 10021. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in t

30、he text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to

31、applies. EN 287-1, Approval testing of welders - Fusion welding - Part 1: Steels. EN 288-1, Specification and qualification of welding procedure for fusion welding - Part 1: General rules. EN 288-2, Specification and qualification of welding procedure for fusion welding - Part 2: Welding procedure s

32、pecification for arc welding of metallic materials. EN 288-3, Specification and qualification of welding procedure for fusion welding - Part 3: Welding procedure tests for arc welding of steels. EN 10002-1, Metallic materials -Tensile testing - Method of test (at ambient temperature). EN 10002-5, Me

33、tallic materials -Tensile test - Method of test at elevated temperatures. EN 10020, Definition and classification of grades of steel. EN 10021, General technical delivery requirements for iron and steel products. EN 10027-1, Designation system for steel -Part 1: Steel names, principal symbols. EN 10

34、027-2, Designation system for steel - Part 2: Steel numbers. EN 10045-1, Metallic materials - Charpy impact test -Test method. EN 10052, Vocabulary of heat treatment terms for ferrous products. EN 10079, Definition of steel products. EN 10204, Metallic products - Inspection documents. prEN 10228-1,

35、Non-destructive testing of steel forgings - Part 1: Magnetic particle inspection. prEN 10228-2, Non-destructive testing of steel forgings - Part 2: Penetrant testing. prEN 10228-3, Non-destructive testing of steel forgings -Part 3: Ultrasonic testing of ferritic or martensitic steel forgings. prEN 1

36、0228-4, Non-destructive testing of steel forgings - Part 4: Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings. EURONORM 168, Iron and Steel products - Inspection documents -Contents. ENV 22605-1, Steel products for pressure purposes - Derivation and verification of el

37、evated temperature properties - Part 1: Yield or proof stress of carbon and low alloy steel products. ENV 22605-2, Steel products for pressure purposes - Derivation and verification of elevated temperature properties - Part 2: Proof stress of austenitic steel products. EN IS0 377, Steel and steel pr

38、oducts - Location of samples and test pieces for mechanical testing. prEN IS0 3651, Determination of resistance to intergranular corrosion stainless steels -Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels - Corrosion test in media containing sulfuric acid. CR 10260, EC

39、ISS Information Circular 10. Designation systems for steel: Additional symbols for steel names. CR 10261, ECISS Information Circular 11. Iron and steel: Review of available methods of chemical analysis. Q BSI 11 October 2002 3 Copyright European Committee for Standardization Provided by IHS under li

40、cense with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 10222-1:1998 3 Definitions 3.1 General For the purposes of this Part of this European Standard the following definitions apply in addition to the definitions in EN 10020, EN 10021, EN 10052, EN 10079

41、and EN IS0 377. 3.2 batch forgings of similar dimensions from the same cast, made by the same forging procedure and from the same heat treatment charge 4 Classification and designation 4.1 Classification The steels in this European Standard are classified as follows: EN 10222-2, Non-alloy quality st

42、eels 1.0352, 1.0426and 1.0436- Alloy special steels -Remaining steels. EN 10222-3, Alloy special steels. EN 10222-4, Non-alloy quality steels - 1.0477, 1.0478, 1.0565 and 1.0571 -Alloy special steels - 1.8932 and 1.8936. EN 10222-5, Alloy special steels. 4.2 Designation The steels in Parts 2 to 5 of

43、 this European Standard are designated in accordance with the requirements of EN 10027-1, EN 10027-2 and CR 10260. 5 Information to be supplied by the purchaser 5.1 Mandatory information The purchaser shall select the steel type, the shape and dimensions of the forging taking the intended use into a

44、ccount. The purchaser shall provide in the purchase order all the information necessary for describing the forging and its characteristics and details concerning delivery including the following: a) the quantity of forgings required; b) the forging dimensions, or the drawing number(s) containing the

45、 dimensions, tolerances and surface finish, to which the forgings shall conform; c) the steel designation of the material of which the forgings are made (see Clause 4); d) whether the purchaser needs to be informed of the forging procedure (see 7.2); e) whether production and testing of the forgings

46、 is to be witnessed by the purchasers representative, and if so, the particular stages in production and testing at which the purchasers representative may require to be present (see Clause 15); f) any required options (see 5.2 and Annex A); g) whether additional sample material is required for weld

47、ing tests, the dimensions and location of such test pieces being agreed with the manufacturer; h) the type of inspection document in accordance with EN 10204. 5.2 Options A number of options are available and these are detailed in Annex A. Where any of the options given are specified at the time of

48、the order, the forgings shall conform to the requirements of any such option, in addition to the mandatory requirements of this Part of this European Standard. If the purchaser does not specify any options at the time of enquiry and order, the manufacturer shall supply in accordance with the basic s

49、pecification. 4 Q BSI 11 October 2002 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EN 10222-1:1998 6 Manufacture of the steel 6.1 Steelmaking process The steel shall be produced by an electric process or one of the basic oxygen processes (see A.l). 6.2 Deoxidation The steel shall be fully killed. 7 Manufacture of the product 7.1 Hot working